hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.0.3 Inter-frequency SS-RSRQ relative measurement accuracy requirements | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 4.7.2.0.3 shall apply.
When RedCap UE is only required to support 1Rx, the relative accuracy requirements in Table 16.7.2.0.3-1 are valid under the following conditions:
- Conditions defined in clause 7.3 of TS 38.101-1 [2] for reference sensiti... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.1 NR SA FR1 SS-RSRQ absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.1.1 Test purpose | The purpose of this test is to verify that the intra-frequency SS-RSRQ absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.1.2 Test applicability | This test applies to all types of NR RedCap UE with 1Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.2.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.2.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.1.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.2.1.4.1 with followings exceptions:
- Table 6.7.2.1.4.1-1 is replaced by Table 16.7.2.1.4.1-1;
- Table 6.7.2.1.4.1-2 is replaced by Table 16.7.2.1.4.1-2;
Table 16.7.2.1.4.1-1: Supported test configurations
Config
Description
16.7.2.1-1
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.2.1.4.2 with following exceptions:
- Table 6.7.2.1.5-1 is replaced by Table 16.7.2.1.5-1;
- Table 6.7.2.1.5-2 is replaced by Table 16.7.2.1.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.1.4.3 Message contents | Same as the message contents given in clause 6.7.2.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.2.1-1 applies to test configuration 16.7.2.1-4.
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.2.1-3
Table 16.7.2.1.4.3-1:... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.1.5 Test requirement | Same as the test requirements given in clause 6.7.2.1.5 with followings exceptions:
- Table 6.7.2.1.5-1 is replaced by Table 16.7.2.1.5-1;
- Table 6.7.2.1.5-2 is replaced by Table 16.7.2.1.5-2;
Table 16.7.2.1.5-1: NR cell specific test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cell 1
Ce... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.2 NR SA FR1 SS-RSRQ absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.2.1 Test purpose | The purpose of this test is to verify that the intra-frequency SS-RSRQ absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.2.2 Test applicability | This test applies to all types of NR RedCap UE with 2Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.2.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.2.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.2.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.2.2.4.1 with followings exceptions:
- Table 6.7.2.1.4.1-1 is replaced by Table 16.7.2.2.4.1-1;
- Table 6.7.2.1.4.1-2 is replaced by Table 16.7.2.2.4.1-2;
Table 16.7.2.2.4.1-1: Supported test configurations
Config
Description
16.7.2.2-1
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.2.1.4.2 with following exceptions:
- Table 6.7.2.1.5-1 is replaced by Table 16.7.2.2.5-1;
- Table 6.7.2.1.5-2 is replaced by Table 16.7.2.2.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.2.4.3 Message contents | Same as the message contents given in clause 6.7.2.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.2.1-1 applies to test configuration 16.7.2.2-4.
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.2.2-3 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.2.5 Test requirement | Same as the test requirements given in clause 6.7.2.1.5 with followings exceptions:
- Table 6.7.2.1.5-1 is replaced by Table 16.7.2.2.5-1;
- Table 6.7.2.1.5-2 is replaced by Table 16.7.2.2.5-2;
Table 16.7.2.2.5-1: NR cell specific test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cell 1
Ce... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3 Inter-frequency measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.1 NR SA FR1-FR1 SS-RSRQ absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.1.1 Test purpose | To verify that the inter-frequency SS-RSRQ absolute measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.8.1.1 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.1.2 Test applicability | This test applies to all types of NR RedCap UE with 1Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.2.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.2.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.1.4.1 Initial conditions | Same as the initial conditions given in 6.7.2.2.1 with followings exceptions:
- Table 6.7.2.2.1.4.1-1 is replaced by Table 16.7.2.3.1.4.1-1;
- Table 6.7.2.2.1.4.1-2 is replaced by Table 16.7.2.3.1.4.1-2;
Table 16.7.2.3.1.4.1-1: Supported test configurations
Config
Description
16.7.2.3.1-1
NR 15 kHz SSB SCS, 10 MHz band... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.1.4.2 Test procedure | Same as the test procedure in clause 6.7.2.1.4.2 with following exceptions:
- Table 6.7.2.2.1.5-1 is replaced by Table 16.7.2.3.1.5-1;
- Table 6.7.2.2.1.5-2 is replaced by Table 16.7.2.3.1.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.1.4.3 Message contents | Same as the message contents in clause 6.7.2.2.1.4.3 with following exceptions:
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.2.3.1-3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.1.5 Test requirement | Same as the test requirements in clause 6.7.2.2.1.5 with followings exceptions:
- Table 6.7.2.2.1.5-1 is replaced by Table 16.7.2.3.1.5-1;
- Table 6.7.2.2.1.5-2 is replaced by Table 16.7.2.3.1.5-2;
Table 16.7.2.3.1.5-1: NR cell specific test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cel... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.2 NR SA FR1-FR1 SS-RSRQ relative measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.2.1 Test purpose | To verify that the inter-frequency SS-RSRQ relative measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.8.1.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.2.2 Test applicability | This test applies to all types of NR RedCap UE with 1Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.2.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.2.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.2.4.1 Initial conditions | Same as the initial conditions given in 6.7.2.2.2 with followings exceptions:
- Table 6.7.2.2.2.4.1-1 is replaced by Table 16.7.2.3.2.4.1-1;
- Table 6.7.2.2.2.4.1-2 is replaced by Table 16.7.2.3.2.4.1-2;
Table 16.7.2.3.2.4.1-1: Supported test configurations
Config
Description
16.7.2.3.2-1
NR 15 kHz SSB SCS, 10 MHz band... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.2.4.2 Test procedure | Same as the test procedure in clause 6.7.2.2.2.4.2 with following exceptions:
- Table 6.7.2.2.2.5-1 is replaced by Table 16.7.2.3.1.5-1;
- Table 6.7.2.2.2.5-2 is replaced by Table 16.7.2.3.2.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.2.4.3 Message contents | Same as the message contents in clause 6.7.2.2.2.4.3 with following exceptions:
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.2.3.2-3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.3.2.5 Test requirement | Same as the test requirements in clause 6.7.2.2.2.5 with followings exceptions:
- Table 6.7.2.2.2.5-1 is replaced by Table 16.7.2.3.1.5-1;
- Table 6.7.2.2.2.5-2 is replaced by Table 16.7.2.3.2.5-1.
Table 16.7.2.3.2.5-1: SS-RSRQ Inter frequency relative accuracy requirements for the reported values
Test 1
Test 2
Test 3
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4 Inter-frequency measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.1 NR SA FR1-FR1 SS-RSRQ absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.1.1 Test purpose | To verify that the inter-frequency SS-RSRQ absolute measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.8.1.1 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.1.2 Test applicability | This test applies to all types of NR RedCap UE with 2Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.2.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.2.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.1.4.1 Initial conditions | Same as the initial conditions given in 6.7.2.2.1 with followings exceptions:
- Table 6.7.2.2.1.4.1-1 is replaced by Table 16.7.2.4.1.4.1-1;
- Table 6.7.2.2.1.4.1-2 is replaced by Table 16.7.2.4.1.4.1-2;
Table 16.7.2.4.1.4.1-1: Supported test configurations
Config
Description
16.7.2.4.1-1
NR 15 kHz SSB SCS, 10 MHz band... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.1.4.2 Test procedure | Same as the test procedure in clause 6.7.2.2.1.4.2 with followings exceptions:
- Table 6.7.2.2.1.5-1 is replaced by Table 16.7.2.4.1.5-1;
- Table 6.7.2.2.1.5-2 is replaced by Table 16.7.2.4.1.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.1.4.3 Message contents | Same as the message contents in clause 6.7.2.2.1.4.3 with following exceptions:
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.2.4.1-3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.1.5 Test requirement | Same as the test requirements in clause 6.7.2.2.1.5 with followings exceptions:
- Table 6.7.2.2.1.5-1 is replaced by Table 16.7.2.4.1.5-1;
- Table 6.7.2.2.1.5-2 is replaced by Table 16.7.2.4.1.5-2;
Table 16.7.2.4.1.5-1: NR cell specific test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cel... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.2 NR SA FR1-FR1 SS-RSRQ relative measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.2.1 Test purpose | To verify that the inter-frequency SS-RSRQ relative measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.8.1.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.2.2 Test applicability | This test applies to all types of NR RedCap UE with 2Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.2.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.2.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.2.4.1 Initial conditions | Same as the initial conditions given in 6.7.2.2.2 with followings exceptions:
- Table 6.7.2.2.2.4.1-1 is replaced by Table 16.7.2.4.2.4.1-1;
- Table 6.7.2.2.2.4.1-2 is replaced by Table 16.7.2.4.2.4.1-2;
Table 16.7.2.4.2.4.1-1: Supported test configurations
Config
Description
16.7.2.4.2-1
NR 15 kHz SSB SCS, 10 MHz band... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.2.4.2 Test procedure | Same as the test procedure in clause 6.7.2.2.2.4.2 with followings exceptions:
- Table 6.7.2.2.2.5-1 is replaced by Table 16.7.2.4.1.5-1;
- Table 6.7.2.2.2.5-2 is replaced by Table 16.7.2.4.2.5-1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.2.4.3 Message contents | Same as the message contents in clause 6.7.2.2.2.4.3 with following exceptions:
- Table H.3.1-3 is used with associated condition SSB.1 RedCap FR1 for test configuration 16.7.2.4.2-3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.2.4.2.5 Test requirement | Same as the test requirements in clause 6.7.2.2.2.5 with followings exceptions:
- Table 6.7.2.2.2.5-1 is replaced by Table 16.7.2.4.1.5-1;
- Table 6.7.2.2.2.5-2 is replaced by Table 16.7.2.4.2.5-1;
Table 16.7.2.4.2.5-1: SS-RSRQ Inter frequency relative accuracy requirements for the reported values
Test 1
Test 2
Test 3
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3 SS-SINR for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.0.1 Intra-frequency SS-SINR measurement accuracy requirements | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 4.7.3.0.1 shall apply.
When RedCap UE is only required to support 1Rx, the absolute accuracy requirements in Table 16.7.3.0.1-1 are valid under the following conditions:
- Conditions defined in clause 7.3I of TS 38.101-1 [2] for reference sensit... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.0.2 Inter-frequency SS-SINR absolute measurement accuracy requirements | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 4.7.3.0.2 shall apply.
When RedCap UE is only required to support 1Rx, the absolute accuracy requirements in Table 16.7.3.0.2-1 are valid under the following conditions:
- Conditions defined in clause 7.3 of TS 38.101-1 [2] for reference sensiti... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.0.3 Inter-frequency SS-SINR relative measurement accuracy requirements | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 4.7.3.0.3 shall apply.
When RedCap UE is only required to support 1Rx, the relative accuracy requirements in Table 16.7.3.0.3-1 are valid under the following conditions:
- Conditions defined in clause 7.3I of TS 38.101-1 [2] for reference sensit... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.1 NR SA FR1 SS-SINR absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.1.1 Test purpose | To verify that the intra-frequency SS-SINR absolute measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.10.1.1 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.1.2 Test applicability | This test applies to all types of NR RedCap UE with 1Rx from Release 17 onwards and supporting SS-SINR measurement. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.3.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.3.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.1.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.3.1.4.1 with followings exceptions:
- Table 6.7.3.1.4.1-1 is replaced by Table 16.7.3.1.4.1-1;
- Table 6.7.3.1.4.1-2 is replaced by Table 16.7.3.1.4.1-2;
Table 16.7.3.1.4.1-1: Supported test configurations
Config
Description
16.7.3.1-1
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.3.1.4.2 with following exceptions:
- Table 6.7.3.1.5-1 is replaced by Table 16.7.3.1.5-1;
- Table 6.7.3.1.5-2 is replaced by Table 16.7.3.1.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.1.4.3 Message contents | Same as the message contents given in clause 6.7.3.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.3.1-1 applies to test configuration 16.7.3.1-4.
Table 16.7.3.1.4.3-1: RLC-Config
Derivation Path: TS 38.508-1 [14], Table 4.6.3-149
Information Element
Value/remark
Comme... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.1.5 Test requirement | Same as the test requirements given in clause 6.7.3.1.5 with followings exceptions:
- Table 6.7.3.1.5-1 is replaced by Table 16.7.3.1.5-1;
- Table 6.7.3.1.5-2 is replaced by Table 16.7.3.1.5-2;
Table 16.7.3.1.5-1: NR cell specific test parameters
Parameter
Unit
Test 1
Test 2
Cell 1
Cell 2
Cell 1
Cell 2
SSB ARFCN
freq1
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.2 NR SA FR1 SS-SINR absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.2.1 Test purpose | To verify that the intra-frequency SS-SINR absolute measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.10.1.1 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.2.2 Test applicability | This test applies to all types of NR RedCap UE with 2Rx from Release 17 onwards and supporting SS-SINR measurement. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.3.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.3.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.2.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.3.1.4.1 with followings exceptions:
- Table 6.7.3.1.4.1-1 is replaced by Table 16.7.3.2.4.1-1;
- Table 6.7.3.1.4.1-2 is replaced by Table 16.7.3.2.4.1-2;
Table 16.7.3.2.4.1-1: Supported test configurations
Config
Description
16.7.3.2-1
NR 15 kHz SSB SCS, 10 MHz bandwid... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.3.1.4.2 with following exceptions:
- Table 6.7.3.1.5-1 is replaced by Table 16.7.3.2.5-1;
- Table 6.7.3.1.5-2 is replaced by Table 16.7.3.2.5-2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.2.4.3 Message contents | Same as the message contents given in clause 6.7.3.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.3.1-1 applies to test configuration 16.7.3.2-4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.2.5 Test requirement | Same as the test requirements given in clause 6.7.3.1.5 with followings exceptions:
- Table 6.7.3.1.5-1 is replaced by Table 16.7.3.2.5-1;
- Table 6.7.3.1.5-2 is replaced by Table 16.7.3.2.5-2;
Table 16.7.3.2.5-1: NR cell specific test parameters
Parameter
Unit
Test 1
Test 2
Cell 1
Cell 2
Cell 1
Cell 2
SSB ARFCN
freq1
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3 Inter-frequency measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.1 NR SA FR1-FR1 SS-SINR absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.1.1 Test purpose | To verify that the inter-frequency SS-SINR absolute measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.12.1.1 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.1.2 Test applicability | This test applies to all types of NR RedCap UE with 1Rx from Release 17 onwards and supporting SS-SINR measurement. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.3.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.3.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.1.4.1 Initial conditions | Same as the initial conditions given in 6.7.3.2.1.4.1 with followings exceptions:
- Table 6.7.3.2.1.4.1-1 is replaced by Table 16.7.3.3.1.4.1-1;
- Table 6.7.3.2.1.4.1-2 is replaced by Table 16.7.3.3.1.4.1-2;
Table 16.7.3.3.1.4.1-1: Supported test configurations
Config
Description
16.7.3.3.1-1
NR 15 kHz SSB SCS, 10 MHz ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.3.2.1.4.2 with following exceptions:
- Table 6.7.3.2.1.5-1 is replaced by Table 16.7.3.3.1.5-1;
- Table 6.7.3.2.1.5-2 is replaced by Table 16.7.3.3.1.5-2; |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.1.4.3 Message contents | Same as the message contents given in clause 6.7.3.2.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.3.2.1-1 applies to test configuration 16.7.3.3.1-4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.1.5 Test requirement | Same as the test requirements in clause 6.7.3.2.1.5 with followings exceptions:
- Table 6.7.3.2.1.5-1 is replaced by Table 16.7.3.3.1.5-1;
- Table 6.7.3.2.1.5-2 is replaced by Table 16.7.3.3.1.5-2;
Table 16.7.3.3.1.5-1: NR cell specific test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cel... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.2 NR SA FR1-FR1 SS-SINR relative measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.2.1 Test purpose | To verify that the inter-frequency SS-SINR relative measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.12.1.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.2.2 Test applicability | This test applies to all types of NR RedCap UE with 1Rx from Release 17 onwards and supporting SS-SINR measurement. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.3.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.3.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.2.4.1 Initial conditions | Same as the initial conditions given in 6.7.3.2.2 with followings exceptions:
- Table 6.7.3.2.2.4.1-1 is replaced by Table 16.7.3.3.2.4.1-1;
- Table 6.7.3.2.2.4.1-2 is replaced by Table 16.7.3.3.2.4.1-2;
Table 16.7.3.3.2.4.1-1: Supported test configurations
Config
Description
16.7.3.3.2-1
NR 15 kHz SSB SCS, 10 MHz band... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.3.2.2.4.2 with following exceptions:
- Table 6.7.3.2.2.5-1 is replaced by Table 16.7.3.3.1.5-1;
- Table 6.7.3.2.2.5-2 is replaced by Table 16.7.3.3.2.5-1; |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.2.4.3 Message contents | Same as the message contents given in clause 6.7.3.2.2.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.3.2.2-1 applies to test configuration 16.7.3.3.2-4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.3.2.5 Test requirement | Same as the test requirements given in clause 6.7.3.2.2.5 with followings exceptions:
- Table 6.7.3.2.2.5-1 is replaced by Table 16.7.3.3.1.5-1;
- Table 6.7.3.2.2.5-2 is replaced by Table 16.7.3.3.2.5-1;
Table 16.7.3.3.2.5-1: SS-SINR Inter frequency relative accuracy requirements for the reported values
Test 1
Test 2
T... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4 Inter-frequency measurement accuracy for 2 Rx UE |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.