hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.1 NR SA FR1-FR1 SS-SINR absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.1.1 Test purpose | To verify that the inter-frequency SS-SINR absolute measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.12.1.1 |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.1.2 Test applicability | This test applies to all types of NR RedCap UE with 2Rx from Release 17 onwards and supporting SS-SINR measurement. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.3.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.3.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.1.4.1 Initial conditions | Same as the initial conditions given in 6.7.3.2.1 with followings exceptions:
- Table 6.7.3.2.1.4.1-1 is replaced by Table 16.7.3.4.1.4.1-1;
- Table 6.7.3.2.1.4.1-2 is replaced by Table 16.7.3.4.1.4.1-2;
Table 16.7.3.4.1.4.1-1: Supported test configurations
Config
Description
16.7.3.4.1-1
NR 15 kHz SSB SCS, 10 MHz band... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.3.2.1.4.2 with following exceptions:
- Table 6.7.3.2.1.5-1 is replaced by Table 16.7.3.4.1.5-1;
- Table 6.7.3.2.1.5-2 is replaced by Table 16.7.3.4.1.5-2; |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.1.4.3 Message contents | Same as the message contents given in clause 6.7.3.2.1.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.3.2.1-1 applies to test configuration 16.7.3.4.1-4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.1.5 Test requirement | Same as the test requirements in clause 6.7.3.2.1.5 with followings exceptions:
- Table 6.7.3.2.1.5-1 is replaced by Table 16.7.3.4.1.5-1;
- Table 6.7.3.2.1.5-2 is replaced by Table 16.7.3.4.1.5-2;
Table 16.7.3.4.1.5-1: NR cell specific test parameters
Parameter
Unit
Test 1
Test 2
Test 3
Cell 1
Cell 2
Cell 1
Cell 2
Cel... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.2 NR SA FR1-FR1 SS-SINR relative measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.2.1 Test purpose | To verify that the inter-frequency SS-SINR relative measurement accuracy is within the specified limits for all bands. This test will verify the requirements in TS 38.133[6] clause 10.1A.12.1.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.2.2 Test applicability | This test applies to all types of NR RedCap UE with 2Rx from Release 17 onwards and supporting SS-SINR measurement. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.3.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.3.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.2.4.1 Initial conditions | Same as the initial conditions given in 6.7.3.2.2 with followings exceptions:
- Table 6.7.3.2.2.4.1-1 is replaced by Table 16.7.3.4.2.4.1-1;
- Table 6.7.3.2.2.4.1-2 is replaced by Table 16.7.3.4.2.4.1-2;
Table 16.7.3.4.2.4.1-1: Supported test configurations
Config
Description
16.7.3.4.2-1
NR 15 kHz SSB SCS, 10 MHz band... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.3.2.2.4.2 with following exceptions:
- Table 6.7.3.2.2.5-1 is replaced by Table 16.7.3.4.1.5-1;
- Table 6.7.3.2.2.5-2 is replaced by Table 16.7.3.4.2.5-1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.2.4.3 Message contents | Same as the message contents given in clause 6.7.3.2.2.4.3 with following exceptions:
- Specific message contents exceptions for test configuration 6.7.3.2.2-1 applies to test configuration 16.7.3.4.2-4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.3.4.2.5 Test requirement | Same as the test requirements in clause 6.7.3.2.2.5 with followings exceptions:
- Table 6.7.3.2.2.5-1 is replaced by Table 16.7.3.4.1.5-1;
- Table 6.7.3.2.2.5-2 is replaced by Table 16.7.3.4.2.5-1;
Table 16.7.3.4.2.5-1: SS-SINR Inter frequency relative accuracy requirements for the reported values
Test 1
Test 2
Test 3
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4 L1-RSRP measurement for beam reporting for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.0.1 SSB based absolute L1-RSRP measurement accuracy requirements | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 4.7.4.0.1 shall apply.
When RedCap UE is only required to support 1Rx, the absolute accuracy requirements in Table 16.7.4.0.1-1 are valid under the following conditions:
- Conditions defined in clause 7.3I of TS 38.101-1 [2] for reference sensit... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.0.2 SSB based relative L1-RSRP measurement accuracy requirements | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 4.7.4.0.2 shall apply.
When RedCap UE is only required to support 1Rx, the relative accuracy requirements in Table 16.7.4.0.2-1 are valid under the following conditions:
- Conditions defined in clause 7.3I of TS 38.101-1 [2] for reference sensit... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.0.3 CSI-RS based absolute L1-RSRP measurement accuracy requirements | The accuracy requirements in clause 4.7.4.0.3 shall apply when RedCap UE is capable of 2Rx. When UE is only required to support 1RX, the absolute accuracy requirements in Table 16.7.4.0.3-1 are valid under the following conditions:
- Conditions defined in clause 7.3I of TS 38.101-1 [2] for reference sensitivity are ful... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.0.4 CSI-RS based relative L1-RSRP measurement accuracy requirementsThe accuracy requirements in clause 4.7.4.0.4 shall apply when RedCap UE is capable of 2Rx. When UE is only required to support 1RX, the absolute accuracy requirements in Table 16.7.4.0.4-1 are valid under the following conditions: | - Conditions defined in clause 7.3I of TS 38.101-1 [2] for reference sensitivity are fulfilled.
- Conditions for L1-RSRP measurements are fulfilled according to TS 38.133 [6] Annex B.2.4.2 for a corresponding Band for each relevant CSI-RS.
- The bandwidth of CSI-RS is 48 PRBs and the density is 3.
The performance with ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1 SSB based L1-RSRP measurements for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.1 NR SA FR1 SSB based L1-RSRP absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.1.1 Test purpose | To verify that the SSB based L1-RSRP absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.1.2 Test applicability | This test applies to all types of NR RedCap UE with 1 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.4.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.4.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.1.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.4.1.1.4.1 with following exceptions:
- Table 6.7.4.1.1.4.1-1 is replaced by Table 16.7.4.1.1.4.1-1;
- Table 6.7.4.1.1.4.1-2 is replaced by Table 16.7.4.1.1.4.1-2;
Table 16.7.4.1.1.4.1-1: Supported test configurations
Test Config
Description
16.7.4.1.1-1
NR 15 kHz SSB S... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.4.1.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.1.4.3 Message contents | Same as the message contents given in clause 6.7.4.1.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.1.5 Test requirement | Same as the thest requirements given in clause 6.7.4.1.1.5 with following exceptions:
- Table 6.7.4.1.1.5-1 is replaced by Table 16.7.4.1.1.5-1;
- Table 6.7.4.1.1.5-2 is replaced by Table 16.7.4.1.1.5-2;
- Table 6.7.4.1.1.5-3 is replaced by Table 16.7.4.1.1.5-3;
Table 16.7.4.1.1.5-1: Cell specific test parameters
Param... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.2 NR SA FR1 SSB based L1-RSRP relative measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.2.1 Test purpose | To verify that the SSB based L1-RSRP relative measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.2.2 Test applicability | This test applies to all types of NR RedCap UE with 1 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.4.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.4.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.2.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.4.1.1.4.1 with following exceptions:
- Table 6.7.4.1.2.4.1-1 is replaced by Table 16.7.4.1.2.4.1-1;
- Table 6.7.4.1.2.4.1-2 is replaced by Table 16.7.4.1.2.4.1-2;
Table 16.7.4.1.2.4.1-1: Supported test configurations
Test Config
Description
16.7.4.1.2-1
NR 15 kHz SSB S... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.4.1.2.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.2.4.3 Message contents | Same as the message contents given in clause 6.7.4.1.2.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.1.2.5 Test requirement | Same as the thest requirements given in clause 6.7.4.1.2.5 with following exceptions:
- Table 6.7.4.1.2.5-1 is replaced by Table 16.7.4.1.1.5-1;
- Table 6.7.4.1.2.5-2 is replaced by Table 16.7.4.1.2.5-2.
Table 16.7.4.1.2.5-1: Void
Table 16.7.4.1.2.5-2: L1-RSRP relative accuracy requirements for the reported values
Test... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2 SSB based L1-RSRP measurements for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.1 NR SA FR1 SSB based L1-RSRP absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.1.1 Test purpose | To verify that the SSB based L1-RSRP absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.1.2 Test applicability | This test applies to all types of NR RedCap UE with 2 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.4.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.1.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.4.1.1.4.1 with following exceptions:
- Table 6.7.4.1.1.4.1-1 is replaced by Table 16.7.4.2.1.4.1-1;
- Table 6.7.4.1.1.4.1-2 is replaced by Table 16.7.4.2.1.4.1-2;
Table 16.7.4.2.1.4.1-1: Supported test configurations
Test Config
Description
16.7.4.2.1-1
NR 15 kHz SSB S... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.4.1.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.1.4.3 Message contents | Same as the message contents given in clause 6.7.4.1.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.1.5 Test requirement | Same as the thest requirements given in clause 6.7.4.1.1.5 with following exceptions:
- Table 6.7.4.1.1.5-1 is replaced by Table 16.7.4.2.1.5-1;
- Table 6.7.4.1.1.5-2 is replaced by Table 16.7.4.2.1.5-2;
Table 16.7.4.2.1.5-1: Cell specific test parameters
Parameter
Config
Unit
Test 1
Test 2
SSB GSCN
1~4
freq1
Duplex mo... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.2 NR SA FR1 SSB based L1-RSRP relative measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.2.1 Test purpose | To verify that the SSB based L1-RSRP relative measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.2.2 Test applicability | This test applies to all types of NR RedCap UE with 2 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.4.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.2.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.4.1.2.4.1 with following exceptions:
- Table 6.7.4.1.2.4.1-1 is replaced by Table 16.7.4.2.2.4.1-1;
- Table 6.7.4.1.2.4.1-2 is replaced by Table 16.7.4.2.2.4.1-2;
Table 16.7.4.2.2.4.1-1: Supported test configurations
Test Config
Description
16.7.4.2.2-1
NR 15 kHz SSB S... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.4.1.2.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.2.4.3 Message contents | Same as the message contents given in clause 6.7.4.1.2.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.2.2.5 Test requirement | Same as the thest requirements given in clause 6.7.4.1.2.5 with following exceptions:
- Table 6.7.4.1.2.5-1 is replaced by Table 16.7.4.2.1.5-1;
- Table 6.7.4.1.2.5-2 is replaced by Table 16.7.4.2.2.5-2;
Table 16.7.4.2.2.5-1: Void
Table 16.7.4.2.2.5-2: L1-RSRP relative accuracy requirements for the reported values
Test... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3 CSI-RS based L1-RSRP measurements for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.1 NR SA FR1 CSI-RS based L1-RSRP absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.1.1 Test purpose | To verify that the CSI-RS based L1-RSRP absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.1.2 Test applicability | This test applies to all types of NR RedCap UE with 1 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.4.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.1.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.4.2.1.4.1 with following exceptions:
- Table 6.7.4.2.1.4.1-1 is replaced by Table 16.7.4.3.1.4.1-1;
- Table 6.7.4.2.1.4.1-2 is replaced by Table 16.7.4.3.1.4.1-2;
Table 16.7.4.3.1.4.1-1: Supported test configurations
Test Config
Description
16.7.4.3.1-1
NR 15 kHz SSB S... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.4.2.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.1.4.3 Message contents | Same as the message contents given in clause 6.7.4.2.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.1.5 Test requirement | Same as the thest requirements given in clause 6.7.4.2.1.5 with following exceptions:
- Table 6.7.4.2.1.5-1 is replaced by Table 16.7.4.3.1.5-1;
- Table 6.7.4.2.1.5-2 is replaced by Table 16.7.4.3.1.5-2;
Table 16.7.4.3.1.5-1: Cell specific test parameters
Parameter
Config
Unit
Test 1
Test 2
SSB GSCN
1~4
freq1
Duplex mo... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.2 NR SA FR1 CSI-RS based L1-RSRP relative measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.2.1 Test purpose | To verify that the CSI-RS based L1-RSRP relative measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.2.2 Test applicability | This test applies to all types of NR RedCap UE with 1 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.4.0.4.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.2.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.4.2.2.4.1 with following exceptions:
- Table 6.7.4.2.2.4.1-1 is replaced by Table 16.7.4.3.2.4.1-1;
- Table 6.7.4.2.2.4.1-2 is replaced by Table 16.7.4.3.2.4.1-2;
Table 16.7.4.3.2.4.1-1: Supported test configurations
Test Config
Description
16.7.4.3.2-1
NR 15 kHz SSB S... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.4.2.2.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.2.4.3 Message contents | Same as the message contents given in clause 6.7.4.2.2.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.3.2.5 Test requirement | Same as the thest requirements given in clause 6.7.4.2.2.5 with following exceptions:
- Table 6.7.4.2.2.5-1 is replaced by Table 16.7.4.3.1.5-1;
- Table 6.7.4.2.2.5-2 is replaced by Table 16.7.4.3.2.5-2;
Table 16.7.4.3.2.5-1: Void
Table 16.7.4.3.2.5-2: L1-RSRP relative accuracy requirements for the reported values
Test... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4 CSI-RS based L1-RSRP measurements for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.1 NR SA FR1 CSI-RS based L1-RSRP absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.1.1 Test purpose | To verify that the CSI-RS based L1-RSRP absolute measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.1.2 Test applicability | This test applies to all types of NR RedCap UE with 2 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.4.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.4.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.1.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.4.2.1.4.1 with following exceptions:
- Table 6.7.4.2.1.4.1-1 is replaced by Table 16.7.4.4.1.4.1-1;
- Table 6.7.4.2.1.4.1-2 is replaced by Table 16.7.4.4.1.4.1-2;
Table 16.7.4.4.1.4.1-1: Supported test configurations
Test Config
Description
16.7.4.4.1-1
NR 15 kHz SSB S... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.4.2.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.1.4.3 Message contents | Same as the message contents given in clause 6.7.4.2.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.1.5 Test requirement | Same as the thest requirements given in clause 6.7.4.2.1.5 with following exceptions:
- Table 6.7.4.2.1.5-1 is replaced by Table 16.7.4.4.1.5-1;
- Table 6.7.4.2.1.5-2 is replaced by Table 16.7.4.4.1.5-2;
Table 16.7.4.4.1.5-1: Cell specific test parameters
Parameter
Config
Unit
Test 1
Test 2
SSB GSCN
1~4
freq1
Duplex mo... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.2 NR SA FR1 CSI-RS based L1-RSRP relative measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.2.1 Test purpose | To verify that the CSI-RS based L1-RSRP relative measurement accuracy is within the specified limits for all bands. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.2.2 Test applicability | This test applies to all types of NR RedCap UE with 2 Rx from Release 17 onwards. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.4.0.4.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.4.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.2.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.4.2.2.4.1 with following exceptions:
- Table 6.7.4.2.2.4.1-1 is replaced by Table 16.7.4.4.2.4.1-1;
- Table 6.7.4.2.2.4.1-2 is replaced by Table 16.7.4.4.2.4.1-2;
Table 16.7.4.4.2.4.1-1: Supported test configurations
Test Config
Description
16.7.4.4.2-1
NR 15 kHz SSB S... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.4.2.2.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.2.4.3 Message contents | Same as the message contents given in clause 6.7.4.2.2.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.4.4.2.5 Test requirement | Same as the thest requirements given in clause 6.7.4.2.2.5 with following exceptions:
- Table 6.7.4.2.2.5-1 is replaced by Table 16.7.4.4.1.5-1;
- Table 6.7.4.2.2.5-2 is replaced by Table 16.7.4.4.2.5-2;
Table 16.7.4.4.2.5-1: Void
Table 16.7.4.4.2.5-2: L1-RSRP relative accuracy requirements for the reported values
Test... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.