hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5 E-UTRAN RSRP for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.0.1 E-UTRAN RSRP absolute accuracy | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 6.7.5.0.1 shall apply.
When RedCap UE is only required to support 1Rx, the requirements for absolute accuracy of RSRP in this clause apply to a cell that has different carrier frequency from the serving cell.
The accuracy requirements in Table 1... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.1 NR SA FR1 - E-UTRA RSRP absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.1.1 Test purpose | To verify that the E-UTRAN RSRP measurement accuracy is within the specified limits. This test will verify the requirements in TS 38.133 [6] clause 10.2A.2 for SA inter-RAT E-UTRAN RSRP measurements. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.1.2 Test applicability | This test applies to all types of NR RedCap UEs with 1Rx from Release 17 onwards and supporting E-UTRA. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.5.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.5.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.1.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.5.1.4.1 with following exceptions:
- Table 6.7.5.1.4.1-1 is replaced by Table 16.7.5.1.4.1-1;
- Table 6.7.5.1.4.1-2 is replaced by Table 16.7.5.1.4.1-2;
Table 16.7.5.1.4.1-1: Supported test configurations
Configuration
Description
16.7.5.1-1
NR 15 kHz SSB SCS, 10 MHz b... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.5.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.1.4.3 Message contents | Same as the message contents given in 6.7.5.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.1.5 Test requirement | Same as the test requirements given in clause 6.7.5.1.5 with following exceptions:
- Table 6.7.5.1.5-1 is replaced by Table 16.7.5.1.5-1;
- Table 6.7.5.1.5-2 is replaced by Table 16.7.5.1.5-2;
- Table 6.7.5.1.5-3 is replaced by Table 16.7.5.1.5-3;
Table 16.7.5.1.5-1: NR Cell specific test parameters (Cell 1)
Parameter
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.2 NR SA FR1 - E-UTRA RSRP absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.2.1 Test purpose | To verify that the E-UTRAN RSRP measurement accuracy is within the specified limits. This test will verify the requirements in TS 38.133 [6] clause 10.2A.2 for SA inter-RAT E-UTRAN RSRP measurements. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.2.2 Test applicability | This test applies to all types of NR RedCap UEs with 2Rx from Release 17 onwards and supporting E-UTRA. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.5.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.5.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.2.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.5.1.4.1 with following exceptions:
- Table 6.7.5.1.4.1-1 is replaced by Table 16.7.5.2.4.1-1;
- Table 6.7.5.1.4.1-2 is replaced by Table 16.7.5.2.4.1-2;
Table 16.7.5.2.4.1-1: Supported test configurations
Configuration
Description
16.7.5.2-1
NR 15 kHz SSB SCS, 10 MHz b... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.5.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.2.4.3 Message contents | Same as the message contents given in 6.7.5.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.5.2.5 Test requirement | Same as the test requirements given in clause 6.7.5.1.5 with following exceptions:
- Table 6.7.5.1.5-1 is replaced by Table 16.7.5.2.5-1;
- Table 6.7.5.1.5-2 is replaced by Table 16.7.5.2.5-2;
- Table 6.7.5.1.5-3 is replaced by Table 16.7.5.2.5-3;
Table 16.7.5.2.5-1: NR Cell specific test parameters (Cell 1)
Parameter
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6 E-UTRAN RSRQ for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.0.1 E-UTRAN RSRQ absolute accuracy | When RedCap UE is capable of 2Rx, the minimum requirements given in clause 6.7.6.0.1 shall apply.
When RedCap UE is only required to support 1Rx, the requirements for absolute accuracy of RSRQ in this clause apply to a cell that has different carrier frequency from the serving cell.
The accuracy requirements in Table 1... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.1 NR SA FR1 - E-UTRA RSRQ absolute measurement accuracy for 1 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.1.1 Test purpose | To verify that the E-UTRAN RSRQ measurement accuracy is within the specified limits. This test will verify the requirements in TS 38.133 [6] clause 10.2A.2 for SA inter-RAT E-UTRAN RSRP measurements. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.1.2 Test applicability | This test applies to all types of NR RedCap UEs with 1Rx from Release 17 onwards and supporting E-UTRA. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.6.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.6.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.1.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.6.1.4.1 with following exceptions:
- Table 6.7.6.1.4.1-1 is replaced by Table 16.7.6.1.4.1-1;
- Table 6.7.6.1.4.1-2 is replaced by Table 16.7.6.1.4.1-2;
Table 16.7.6.1.4.1-1: Supported test configurations
Configuration
Description
16.7.6.1-1
NR 15 kHz SSB SCS, 10 MHz b... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.1.4.2 Test procedure | Same as the test procedure given in clause 6.7.6.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.1.4.3 Message contents | Same as the message contents given in 6.7.6.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.1.5 Test requirement | Same as the test requirements given in clause 6.7.6.1.5 with following exceptions:
- Table 6.7.6.1.5-1 is replaced by Table 16.7.6.1.5-1;
- Table 6.7.6.1.5-2 is replaced by Table 16.7.6.1.5-2;
- Table 6.7.6.1.5-3 is replaced by Table 16.7.6.1.5-3;
Table 16.7.6.1.5-1: NR Cell specific test parameters (Cell 1)
Parameter
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.2 NR SA FR1 - E-UTRA RSRQ absolute measurement accuracy for 2 Rx UE | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.2.1 Test purpose | To verify that the E-UTRAN RSRQ measurement accuracy is within the specified limits. This test will verify the requirements in TS 38.133 [6] clause 10.2A.2 for SA inter-RAT E-UTRAN RSRP measurements. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.2.2 Test applicability | This test applies to all types of NR RedCap UEs with 2Rx from Release 17 onwards and supporting E-UTRA. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.2.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 16.7.6.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.16.7.6.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.2.4.1 Initial conditions | Same as the initial conditions given in clause 6.7.6.1.4.1 with following exceptions:
- Table 6.7.6.1.4.1-1 is replaced by Table 16.7.6.2.4.1-1;
- Table 6.7.6.1.4.1-2 is replaced by Table 16.7.6.2.4.1-2;
Table 16.7.6.2.4.1-1: Supported test configurations
Configuration
Description
16.7.6.2-1
NR 15 kHz SSB SCS, 10 MHz b... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.2.4.2 Test procedure | Same as the test procedure given in clause 6.7.6.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.2.4.3 Message contents | Same as the message contents given in 6.7.6.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 16.7.6.2.5 Test requirement | Same as the test requirements given in clause 6.7.6.1.5 with following exceptions:
- Table 6.7.6.1.5-1 is replaced by Table 16.7.6.2.5-1;
- Table 6.7.6.1.5-2 is replaced by Table 16.7.6.2.5-2;
- Table 6.7.6.1.5-3 is replaced by Table 16.7.6.2.5-3;
Table 16.7.6.2.5-1: NR Cell specific test parameters (Cell 1)
Parameter
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17 NR standalone tests in FR2 for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1 RRC_IDLE state mobility for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1 NR cell re-selection for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.0.1 Minimum conformance requirements for intra-frequency cell re-selection for RedCap | The UE shall be able to identify new intra-frequency cells and perform SS-RSRP and SS-RSRQ measurements of the identified intra-frequency cells without an explicit intra-frequency neighbour list containing physical layer cell identities.
The UE shall be able to evaluate whether a newly detectable intra-frequency cell m... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.0.2 Minimum conformance requirements for inter-frequency cell re-selection for RedCap | The UE shall be able to identify new inter-frequency cells and perform SS-RSRP or SS-RSRQ measurements of identified inter-frequency cells if carrier frequency information is provided by the serving cell, even if no explicit neighbour list with physical layer cell identities is provided.
If Srxlev > SnonIntraSearchP an... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.0.3 Minimum conformance requirements for intra-frequency cell re-selection for RedCap UE configured with stationary relaxed measurement criterion | This clause contains requirements for measurements on intra-frequency NR cells provided that:
- UE is configured with stationaryMobilityEvaluation [2] criterion and UE has fulfilled that criterion, or
- UE is configured with both stationaryMobilityEvaluation [2] criterion and cellEdgeEvaluationWhileStationary [2] crite... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.0.4 Minimum conformance requirements for inter-frequency cell re-selection for RedCap UE configured with stationary relaxed measurement criterion | This clause contains requirements for measurements on inter-frequency NR cells provided that:
- UE is configured with stationaryMobilityEvaluation [2] criterion and UE has fulfilled that criterion, or
- UE is configured with both stationaryMobilityEvaluation [2] criterion and cellEdgeEvaluationWhileStationary [2] crite... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.1 NR SA FR2 Cell reselection for 2 Rx UE | Editor’s Note: This test case is complete for the following configurations:
• Test frequency f ≤ 40.8 GHz.
• UE PC3
This test case is incomplete for Test frequency f > 40.8 GHz
This test case is incomplete for UE power class other than PC3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.1.1 Test purpose | The purpose of this test is to verify the requirement for the NR SA intra-frequency cell reselection in FR2 for 2 Rx RedCap UEs. The requirements are specified in TS 38.133 [6] in clause 4.2B.2.3.. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.1.2 Test applicability | This test applies to all types of NR RedCap UE release 17 and forward. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.1.3 Minimum conformance requirements | The minimum conformance requirements are defined in clause 17.1.1.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.1.1.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.1.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.1.1.1.4.1-1.
Table 17.1.1.1.4.1-1: Supported test configurations for NR SA FR2 Cell reselection to FR2 intra-frequency NR case for 2 Rx
Configuration
Description
17.1.1.1-1
120 kHz SSB SCS, 100 MHz bandwidth, TDD duplex mode
17.1.1.1-2
240 kHz S... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.1.4.2 Test procedure | Two cells are deployed in the test, which are one FR2 NR PCell (Cell 1) and an NR neighbour cell (Cell 2) on the same frequency. The test consists of 3 successive time periods, with time duration of T1, T2, and T3 respectively. Only cell 1 is already identified by the UE prior to the start of the test. Cell 1 and cell ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.1.4.3 Message contents | Message contents are according to TS 38.508-1 [14] clause 7.3 with the following exceptions:
Table 17.1.1.1.4.3-1: Common Exception messages
Default Message Contents
Common contents of system information blocks exceptions
Table H.2.1-2
Default RRC messages and information elements contents exceptions
Table 7.1.1.1.4.3-... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.1.5 Test requirement | Table 17.1.1.1.5-1 defines the primary level settings including test tolerances for NR – E-UTRA cell re-selection test case in AWGN for 2 Rx UE.
Table 17.1.1.1.5-1: Cell specific test parameters for NR SA FR2 Cell reselection to FR2 intra-frequency NR case for 2 Rx
Parameter
Unit
Test configuration
Cell 1
Cell 2
T1
T2
... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.2 NR SA FR2-FR2 Cell reselection for 2 Rx UE | Editor’s Note: This test case is complete for the following configurations:
• Test frequency f ≤ 40.8 GHz.
• UE PC3
This test case is incomplete for Test frequency f > 40.8 GHz
This test case is incomplete for UE power class other than PC3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.2.1 Test purpose | The purpose of this test is to verify the requirement for the NR SA intra-frequency cell reselection in FR2 for 2 Rx RedCap UEs. The requirements are specified in TS 38.133 [6] in clause 4.2B.2.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.2.2 Test applicability | This test applies to all types of NR RedCap UE release 17 and forward. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.2.3 Minimum conformance requirements | The minimum conformance requirements are defined in clause 17.1.1.0.2.
The normative reference for this requirement is TS 38.133 [6] clause A.17.1.1.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.2.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.2.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.1.1.2.4.1-1.
Table 17.1.1.2.4.1-1: Supported test configurations for NR SA FR2-FR2 Cell reselection to FR2 inter-frequency NR for 2 Rx
Configuration
Description for serving cell
Description for target cell
17.1.1.2-1
120 kHz SSB SCS, 100 MHz ban... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.2.4.2 Test procedure | Two cells on two RF channels are deployed in the test, which are one FR2 NR PCell (Cell 1) on RF channel 1 and an NR neighbour cell (Cell 2) on RF channel 2. The test consists of 3 successive time periods, with time duration of T1, T2, and T3 respectively. Only cell 1 is already identified by the UE prior to the start ... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.2.4.3 Message contents | Message contents are according to TS 38.508-1 [14] clause 7.3 with the following exceptions:
Table 17.1.1.2.4.3-1: Common Exception messages
Default Message Contents
Common contents of system information blocks exceptions
Table H.2.2-1 for NR Cell 1
Default RRC messages and information elements contents exceptions
Tabl... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.2.5 Test requirement | Table 17.1.1.2.5-1 defines the primary level settings including test tolerances for NR – E-UTRA cell re-selection test case in AWGN for 2 Rx UE.
Table 17.1.1.2.5-1: Cell specific test parameters for NR SA FR2-FR2 Cell reselection to FR2 inter-frequency NR for 2 Rx
Parameter
Unit
Test configuration
Cell 1
Cell 2
T1
T2
T... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.3 NR SA FR2 Cell reselection for UE fulfilling stationary relaxed measurement criterion for 2 Rx UE | Editor’s Note: This test case is complete for the following configurations:
• Test frequency f ≤ 40.8 GHz.
• UE PC3
This test case is incomplete for Test frequency f > 40.8 GHz
This test case is incomplete for UE power class other than PC3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.3.1 Test purpose | The purpose of this test is to verify the requirement for the NR SA intra-frequency cell reselection in FR2 for 2 Rx RedCap UEs. The requirements are specified in TS 38.133 [6] in clause 4.2B.2.9.2.. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.3.2 Test applicability | This test applies to all types of NR RedCap UE release 17 and forward supporting Rel-17 relaxed RRM measurements of neighbour cells in RRC_IDLE/RRC_INACTIVE. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.3.3 Minimum conformance requirements | The minimum conformance requirements are defined in clause 17.1.1.0.3.
The normative reference for this requirement is TS 38.133 [6] clause A.17.1.1.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.3.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.3.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.1.1.3.4.1-1.
Table 17.1.1.3.4.1-1: Supported test configurations for NR SA FR2 Cell reselection to FR2 intra-frequency NR for UE fulfilling stationary relaxed measurement criterion for 2 Rx UE
Configuration
Description
17.1.1.3-1
120 kHz SSB SCS... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.3.4.2 Test procedure | Two cells are deployed in the test, which are one FR2 NR PCell (Cell 1) and an NR neighbour cell (Cell 2) on the same frequency. The test consists of 2 successive time periods, with time duration of T1, T2 respectively. Both cell 1 and cell2 are already identified by the UE prior to the start of the test. Cell 1 and ce... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.3.4.3 Message contents | Message contents are according to TS 38.508-1 [14] clause 7.3 with the following exceptions:
Table 17.1.1.3.4.3-1: Common Exception messages
Default Message Contents
Common contents of system information blocks exceptions
Table H.2.1-2
Default RRC messages and information elements contents exceptions
Table 17.1.1.3.4.3... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.3.5 Test requirement | Table 17.1.1.3.5-1 defines the primary level settings including test tolerances for NR – E-UTRA cell re-selection test case in AWGN for UE fulfilling stationary relaxed measurement criterion for 2 Rx UE.
Table 17.1.1.3.5-1: Cell specific test parameters for NR SA FR2 Cell reselection to FR2 intra-frequency NR for UE fu... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.4 NR SA FR2-FR2 Cell reselection for UE fulfilling stationary mobility relaxed measurement criterion for 2 Rx UE | Editor’s Note: This test case is complete for the following configurations:
• Test frequency f ≤ 40.8 GHz.
• UE PC3
This test case is incomplete for Test frequency f > 40.8 GHz
This test case is incomplete for UE power class other than PC3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.4.1 Test purpose | The purpose of this test is to verify the requirement for the NR SA intra-frequency cell reselection in FR2 for 2 Rx RedCap UEs. The requirements are specified in TS 38.133 [6] in clause 4.2B.2.10.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.4.2 Test applicability | This test applies to all types of NR RedCap UE release 17 and forward supporting Rel-17 relaxed RRM measurements of neighbour cells in RRC_IDLE/RRC_INACTIVE. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.4.3 Minimum conformance requirements | The minimum conformance requirements are defined in clause 17.1.1.0.4.
The normative reference for this requirement is TS 38.133 [6] clause A.17.1.1.4. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.4.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.4.4.1 Initial conditions | This test shall be tested using any of the test configurations in Table 17.1.1.4.4.1-1.
Table 17.1.1.4.4.1-1: Supported test configurations for NR SA FR2-FR2 Cell reselection to FR2 inter-frequency NR for UE fulfilling stationary mobility relaxed measurement criterion for 2 Rx UE
Configuration
Description for serving c... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.4.4.2 Test procedure | The test consists of one active cell and one neighbour cell on two different NR RF channels. The UE is requested to monitor the neighbouring cell on one of the NR carriers. The test consists of two successive time periods, with time duration of T1, T2 respectively. Both Cell 1 and Cell 2 are already identified by the U... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.4.4.3 Message contents | Message contents are according to TS 38.508-1 [14] clause 7.3 with the following exceptions:
Table 17.1.1.5.4.3-1: Common Exception messages
Default Message Contents
Common contents of system information blocks exceptions
Default RRC messages and information elements contents exceptions
Table 17.1.1.5.4.3-2: RACH-Confi... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.1.1.4.5 Test requirement | Table 17.1.1.4.5-1 defines the primary level settings including test tolerances for NR – E-UTRA cell re-selection test case in AWGN for UE fulfilling stationary relaxed measurement criterion for 2 Rx UE.
Table 17.1.1.4.5-1: Cell specific test parameters for NR SA FR2-FR2 Cell reselection to FR2 inter-frequency NR for U... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2 RRC_INACTIVE state mobility for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1 Configured Grant based Small Data Transmissions for RedCap | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.0 Minimum conformance requirements | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.0.1 Minimum conformance requirements for TA validation using CG-SDT | The requirements in this clause are applicable when the UE is configured with timing alignment (TA) validation using cg-SDT-RSRP-ChangeThreshold for transmitting in uplink using CG-SDT as specified in TS 38.331 [13].
The requirements in this clause are applicable for the UE performing small data tranmissions using conf... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.1 NR SA FR2 TA validation for CG-SDT for 2 Rx UE | Editor’s Note: This test case is incomplete in following aspects:
- Test procedure needs further updates;
- TT analysis is still missing. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.1.1 Test purpose | To verify that the UE properly perform TA validation for CG-SDT transmission as specified in TS 38.133 [6] clause 5.2B.2.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.1.2 Test applicability | This test applies to all types of NR RedCap UE with 2Rx from Release 17 onwards and supporting CG-SDT. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.1.3 Minimum conformance requirements | The minimum conformance requirements are specified in clause 17.2.1.0.1.
The normative reference for this requirement is TS 38.133 [6] clause A.17.2.1.1. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.1.4 Test description | |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.1.4.1 Initial conditions | Same as the initial conditions given in clause 7.2.1.1.4.1 with following exceptions:
- Table 7.2.1.1.4.1-1 is replaced by Table 17.2.1.1.4.1-1;
- Table 7.2.1.1.4.1-2 is replaced by Table 17.2.1.1.4.1-2;
- Table 7.2.1.1.4.1-3 is replaced by Table 17.2.1.1.4.1-3;
Table 17.2.1.1.4.1-1: Supported test configurations
Table... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.1.4.2 Test procedure | Same as the test procedure given in clause 7.2.1.1.4.2. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.1.4.3 Message contents | Same as the message contents given in 7.2.1.1.4.3. |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.2.1.1.5 Test requirements | Same as the test requirements given in clause 7.2.1.1.5 with following exceptions:
- Table 7.2.1.1.5-1 is replaced by Table 17.2.1.1.5-1.
Table 17.2.1.1.5-1: Cell-specific test parameters (NR Cell 1)
Parameter
Unit
Test 1
T1
T2
T3
T4
T5
AoA setup
Setup 1 defined in A.3.15
Assumption for UE beams Note 4
Rough
EPRE ratio... |
f6aa351f9dfcf54f60d7745530e70f1e | 38.533 | 17.3 RRC_CONNECTED state mobility for RedCap |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.