hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.7.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.7.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) A call is set up according to the Generic call setup procedure in TS34.108 [3] sub clause 7.3.2. The 12,2 kbps UL reference measurement c... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.7.4.2 Procedure | NOTE: CFNs are given in this procedure for reference as examples only. A fixed offset may be applied to the CFNs.
1) Before proceeding with step (3) below, set the output power of the UE to be in the range -36 ± 9 dBm. This may be achieved by setting the downlink signal (Îor) to yield an appropriate open loop output po... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.7.5 Test requirements | For ease of reference, the following uplink output power measurements are defined in figure 5.7.4. In this figure:
- Pg is the RRC filtered mean power in an uplink transmission gap, excluding the 25 ms transient periods.
- Pa is the mean power in the last slot before a compressed frame (or pair of compressed frames), e... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.8 Occupied Bandwidth (OBW) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.8.1 Definition and applicability | Occupied bandwidth is a measure of the bandwidth containing 99 % of the total integrated power of the transmitted spectrum, centred on the assigned channel frequency.
The requirements and this test apply to all types of UTRA for the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.8.2 Minimum Requirements | The occupied channel bandwidth shall be less than 5 MHz based on a chip rate of 3,84 Mcps.
The normative reference for this requirement is TS 25.101 [1] clause 6.6.1. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.8.3 Test purpose | To verify that the UE occupied channel bandwidth is less than 5 MHz based on a chip rate of 3,84 Mcps.
Excess occupied channel bandwidth increases the interference to other channels or to other systems. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.8.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.8.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) A call is set up according to the Generic call setup procedure in TS34.108 [3] sub clause 7.3.2.
3) Enter the UE i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.8.4.2 Procedure | 1) Set and send continuously Up power control commands to the UE until the UE output power shall be maximum level.
2) Measure the power spectrum distribution within two times or more range over the requirement for Occupied Bandwidth specification centring on the current carrier frequency with 30 kHz or less RBW. The ch... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.8.5 Test Requirements | The measured Occupied Bandwidth, derived in step 6), shall not exceed 5 MHz.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement ha... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.9 Spectrum emission mask | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.9.1 Definition and applicability | The spectrum emission mask of the UE applies to frequencies, which are between 2.5 MHz and 12.5 MHz away from the UE centre carrier frequency. The out of channel emission is specified relative to the RRC filtered mean power of the UE carrier.
The requirements and this test apply to all types of UTRA for the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.9.2 Minimum Requirements | The power of any UE emission shall not exceed the levels specified in Table 5.9.1. The absolute requirement is based on a -50 dBm/3.84 MHz minimum power threshold for the UE. This limit is expressed for the narrower measurement bandwidths as -55.8 dBm/1 MHz and -71.1 dBm/30 kHz. The requirements are applicable for all ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.9.3 Test purpose | To verify that the power of UE emission does not exceed the prescribed limits shown in table 5.9.1.
Excess emission increases the interference to other channels or to other systems. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.9.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.9.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) A call is set up according to the Generic call setup procedure in TS34.108 [3] sub clause 7.3.2.
3) Enter the UE i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.9.4.2 Procedure | 1) Set and send continuously Up power control commands to the UE until the UE output power shall be maximum level.
2) Measure the power of the transmitted signal with a measurement filter of bandwidths according to table 5.9.2 and 5.9.2A, 5.9.2B, 5.9.2C if applicable. For measurements using 1 MHz or 100KHz measurement ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.9.5 Test requirements | The result of clause 5.9.4.2 step 4) shall fulfil the requirements of table 5.9.2.
For operation in band II, IV, V, X, XII, XIII, XIV, XXV and XXVI both minimum requirement in table 5.9.2 and the applicable additional requirement in Tables 5.9.2A, 5.9.2B, or 5.9.2C need to be satisfied.
Table 5.9.2: Spectrum Emission ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.10 Adjacent Channel Leakage Power Ratio (ACLR) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.10.1 Definition and applicability | ACLR is the ratio of the RRC filtered mean power centred on the assigned channel frequency to the RRC filtered mean power centred on an adjacent channel frequency.
The requirements and this test apply to all types of UTRA for the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.10.2 Minimum Requirements | If the adjacent channel RRC filtered mean power is greater than -50dBm then the ACLR shall be higher than the value specified in table 5.10.1.
Table 5.10.1: UE ACLR
Power Class
UE channel
ACLR limit
3
+5 MHz or -5 MHz
33 dB
3
+10 MHz or -10 MHz
43 dB
4
+5 MHz or -5 MHz
33 dB
4
+10 MHz or -10 MHz
43 dB
NOTE 1: The requi... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.10.3 Test purpose | To verify that the UE ACLR does not exceed prescribed limit shown in table 5.10.1.
Excess ACLR increases the interference to other channels or to other systems. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.10.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.10.4.1 Initial conditions | Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) A call is set up according to the Generic call setup procedure in TS34.108 [3] sub cla... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.10.4.2 Procedure | 1) Set and send continuously Up power control commands to the UE until the UE output power shall be maximum level.
2) Measure the RRC filtered mean power.
3) Measure the RRC filtered mean power of the first adjacent channels and the second adjacent channels.
4) Calculate the ratio of the power between the values measur... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.10.5 Test requirements | If the measured adjacent channel RRC filtered mean power, derived in step 3), is greater than -50,0 dBm then the measured ACLR, derived in step 4), shall be higher than the limit in table 5.10.2.
Table 5.10.2: UE ACLR
Power Class
UE channel
ACLR limit
3
+5 MHz or -5 MHz
32,2 dB
3
+10 MHz or -10 MHz
42,2 dB
4
+5 MHz or ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.11 Spurious Emissions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.11.1 Definition and applicability | Spurious emissions are emissions which are caused by unwanted transmitter effects such as harmonics emission, parasitic emission, intermediation products and frequency conversion products, but exclude out of band emissions.
The frequency boundary and the detailed transitions of the limits between the requirement for ou... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.11.2 Minimum Requirements | These requirements are only applicable for frequencies, which are greater than 12.5 MHz away from the UE centre carrier frequency.
Table 5.11.1a: General spurious emissions requirements
Frequency Bandwidth
Measurement Bandwidth
Minimum requirement
Note
9 kHz £ f < 150 kHz
1 kHz
-36 dBm
150 kHz £ f < 30 MHz
10 kHz
-36 d... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.11.3 Test purpose | To verify that the UE spurious emissions do not exceed described value shown in table 5.11.1a, table 5.11.1b and table 5.11.1c.
Excess spurious emissions increase the interference to other systems. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.11.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.11.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.8.
2) A call is set up according to the Generic call setup procedure in TS34.108 [3] sub clause 7.3.2.
3) Enter the UE i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.11.4.2 Procedure | 1) Set and send continuously Up power control commands to the UE until the UE output power shall be maximum level.
2) Sweep the spectrum analyzer (or equivalent equipment) over a frequency range and measure the average power of spurious emission. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.11.5 Test requirements | The measured average power of spurious emission, derived in step 2), shall not exceed the described value in tables 5.11.2a, 5.11.2b and 5.11.2c.
These requirements are only applicable for frequencies, which are greater than 12.5 MHz away from the UE centre carrier frequency.
Table 5.11.2a: General spurious emissions t... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.12 Transmit Intermodulation | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.12.1 Definition and applicability | The transmit intermodulation performance is a measure of the capability of the transmitter to inhibit the generation of signals in its non linear elements caused by presence of the wanted signal and an interfering signal reaching the transmitter via the antenna.
UE(s) transmitting in close vicinity of each other can pr... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.12.2 Minimum Requirements | The UE transmit intermodulation shall not exceed the described value in table 5.12.1.
Table 5.12.1: Transmit Intermodulation
CW Signal Frequency Offset from Transmitting Carrier
5MHz
10MHz
Interference CW Signal Level
-40 dBc
Intermodulation Product
-31 dBc
-41 dBc
The normative reference for this requirement is TS 25.... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.12.3 Test purpose | To verify that the UE transmit intermodulation does not exceed the described value in table 5.12.1.
An excess transmit intermodulation increases transmission errors in the up link own channel when other transmitter exists nearby. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.12.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.12.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.2.
2) A call is set up according to the Generic call setup procedure in TS34.108 [3] sub clause 7.3.2.
3) Enter the UE into loopback test mode ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.12.4.2 Procedure | 1) Set and send continuously Up power control commands to the UE until the UE output power shall be maximum level.
2) Set the frequency of the CW generator to the offset 1 or offset 2 as shown in table 5.12.2.
3) Measure the RRC filtered mean power of the UE.
4) Search the intermodulation product signal, then measure t... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.12.5 Test requirements | The ratio derived in step 4), shall not exceed the described value in table 5.12.2.
Table 5.12.2: Transmit Intermodulation
CW Signal Frequency Offset from Transmitting Carrier
5MHz
10MHz
Interference CW Signal Level
-40 dBc
Intermodulation Product
-31 dBc
-41 dBc
NOTE: If the above Test Requirement differs from the Min... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13 Transmit Modulation | Transmit modulation defines the modulation quality for expected in-channel RF transmissions from the UE. The requirements apply to all transmissions including the PRACH/PCPCH pre-amble and message parts and all other expected transmissions for release 99 and release 4 only. For release 5 and later the requirements appl... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.1 Error Vector Magnitude (EVM) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.1.1 Definition and applicability | The Error Vector Magnitude is a measure of the difference between the reference waveform and the measured waveform. This difference is called the error vector. Both waveforms pass through a matched Root Raised Cosine filter with bandwidth 3,84 MHz and roll-off =0,22. Both waveforms are then further modified by select... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.1.2 Minimum Requirements | The EVM shall not exceed 17,5 % for the parameters specified in table 5.13.1.
Table 5.13.1: Parameters for EVM
Parameter
Level / Status
Unit
Output power
³ -20
dBm
Operating conditions
Normal conditions
Power control step size
1
dB
The normative reference for this requirement is TS 25.101 [1] clause 6.8.3.0. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.1.3 Test purpose | To verify that the EVM does not exceed 17,5 % for the specified parameters in table 5.13.1.
An excess EVM increases transmission errors in the up link own channel. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) A call is set up according to the Generic call setup procedure in TS34.108 [3] sub clause 7.3.2.
3) Enter the UE i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.1.4.2 Procedure | 1) Set and send continuously Up power control commands to the UE until the UE output power shall be maximum level.
2) Measure the EVM using Global In-Channel Tx-Test (annex B).
3) Set the power level of UE to -18dBm or send Down power control commands (1dB step size should be used.) to the UE until UE output power shal... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.1.5 Test requirements | The measured EVM, derived in step 2) and 4), shall not exceed 17,5 %. for parameters specified in table 5.13.1 Parameters for EVM.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.2 Peak code domain error | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.2.1 Definition and applicability | The Peak Code Domain Error is computed by projecting power of the error vector (as defined in clause 5.13.1.1) onto the code domain at a specific spreading factor. The Code Domain Error for every code in the domain is defined as the ratio of the mean power of the projection onto that code, to the mean power of the comp... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.2.2 Minimum Requirements | The peak code domain error shall not exceed -15 dB at spreading factor 4 for the parameters specified in table 5.13.3.The requirements are defined using the UL reference measurement channel (768 kbps) specified in clause C.2.5.
Table 5.13.3: Parameters for Peak code domain error
Parameter
Level / Status
Unit
Output pow... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.2.3 Test purpose | To verify that the UE peak code domain error does not exceed -15 dB for the specified parameters in table 5.13.3.
An excess peak code domain error increases transmission errors in the up link own channel. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) A call is set up according to the Generic call setup procedure in TS34.108 [3] sub clause 7.3.2, and RF parameters... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.2.4.2 Procedure | 1) Set and send continuously Up power control commands to the UE until the UE output power shall be maximum level.
2) Measure the Peak code Domain error using Global In-Channel Tx-Test (annex B).
3) Set the power level of UE to -18dBm or send Down power control commands (1dB step size should be used.) to the UE until U... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.2.5 Test requirements | The measured Peak code domain error, derived in step 2) and 4), shall not exceed -14 dB.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum R... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.3 UE phase discontinuity | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.3.1 Definition and applicability | Phase discontinuity is the change in phase between any two adjacent timeslots. The EVM for each timeslot (excluding the transient periods of 25 s on either side of the nominal timeslot boundaries) shall be measured according to subclause 5.13.1. The frequency, absolute phase, absolute amplitude and chip clock timing u... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.3.2 Minimum requirements | The rate of occurrence of any phase discontinuity on an uplink DPCH for the parameters specified in table 5.13.3.1 shall not exceed the values specified in table 5.13.3.2. Phase shifts that are caused by changes of the UL transport format combination (TFC) and compressed mode are not included. When calculating the phas... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.3.3 Test purpose | To verify that the UE phase discontinuity is within the limits shown in clause 5.13.3.2.
To verify that any timeslot used in the calculation of a phase discontinuity result also passes the frequency error and EVM requirements referenced in clause 5.3 2 and 5.13.3.2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) A call is set up according to the Generic call setup procedure using power control algorithm 1 as specified in TS34.108 [3] sub clause 7.... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.3.5 Test requirements | a) During 5.13.3.4.2 step 3, and step 5, the EVM of every measured slot which is greater than or equal to -20 dBm shall not exceed 17.5%
b) During 5.13.3.4.2 step 3, and step 5, the Frequency error of every measured slot shall not exceed ±(0,1 ppm + 10 Hz).
c) During 5.13.3.4.2 step 3, and step 5; the phase discontinui... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.4 PRACH preamble quality | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.4.1 Definition and applicability | PRACH preamble quality is a measure of the ability of the UE to transmit the PRACH preamble in accordance with the core requirements so that the Node B can reliably decode the PRACH.
This test applies to all types of UTRA for the FDD UE from Release 5 onwards. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.4.2 Minimum requirements | The EVM of the PRACH preamble observed over the interval of 3904 chips (i.e. excluding the transient periods) shall not exceed 17.5%.
The reference for this requirement is TS 25.101 [1] clause 6.8.2.
The UE modulated carrier frequency used to transmit the PRACH preamble observed over the interval of 3904 chips (i.e. ex... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.4.3 Test purpose | The test purpose is to verify that the transmission quality of the first PRACH preamble meets the minimum requirements for modulation quality, carrier frequency, access slot and signature as defined in 5.13.4.2. The UE is tested at nominal maximum output power and nominally 5.6 dB to 8.6 dB above reference sensitivity,... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.4.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.4.4.1 Initial conditions | Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) A call is set up according to the Generic call setup procedure, using the modified par... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.4.4.2 Procedure | 1) Set the TX output level of the SS to obtain Îor at the UE antenna connector. Îor shall be according to table 5.13.4.1 depending on the power class of the UE.
2) The SS shall initiate a call by sending PAGING TYPE 1 message and measure the first RF transmission from the UE.
3) The SS shall determine the access slot u... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.4.5 Test requirements | For all the transmitted PRACH preambles measured in 5.13.4.4.2 step 3:
1) The EVM shall not exceed 17,5 %.
2) The frequency error shall not exceed ±(0,1 ppm + 10 Hz).
3) The detected access slot and signature shall be correct according to the physical random access procedure defined in [5].
NOTE: If the above Test Requ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.5 In-band emission for DC-HSUPA | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.5.1 Definition and applicability | The in-band emission is measured as the ratio of the UE output power in one carrier in dual cells to the UE output power in the other carrier, where the power in the former carrier shall be set to the minimum output power and the power in the latter carrier to the maximum output power. It is necessary to verify the req... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.5.2 Minimum Requirements | The in-band emission shall not exceed the value specified in Table 5.13.5.1.
Table 5.13.5.1: In-band emission minimum requirements for DC-HSUPA
Parameter Description
Unit
Limit
In-band emission
dBc
-24
NOTE: The measurement bandwidth is 3.84 MHz centred on each carrier frequency and the limit is expressed as a ratio of... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.5.3 Test purpose | To verify that the in-band emission, during DC-HSUPA transmission, does not exceed the prescribed limits shown in table 5.13.5.1. This is applicable for all values of c , d ,hs, ec and ed as specified in [5]. The maximum output power with HS-DPCCH and/or E-DCH is specified in table 5.2BA.1.
Excess in-band emiss... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.5.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.5.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect the SS (node B emulator) to the UE antenna connector as shown in figure A.41.
2) The UL Reference Measurement Channel and parameters are specified in Annex C.2.6 and C.11A. The... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.5.4.2 Procedure | 1) Set the Absolute Grant according to Table C.11A.1.1.
2) The SS starts transmitting HSDPA and the UE loops the received data back on E-DCH.
3) Set and send continuously Up power control commands to one carrier and Down power control commands to the other carrier to reach the power levels as given in table 5.13.5.3. W... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 5.13.5.5 Test requirements | The result of clause 5.13.5.4.2 step 4) shall fulfil the requirements of table 5.13.5.4.
Table 5.13.5.4: In-band Emission Requirement for DC-HSUPA
Parameter Description
Unit
Limit
In-band emission
dBc
-23.2
NOTE: The measurement bandwidth is 3.84 MHz centred on each carrier frequency and the limit is expressed as a rat... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6 Receiver Characteristics | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.1 General | Receiving performance test of the UE is implemented during communicating with the SS via air interface. The procedure is using normal call protocol until the UE is communicating on traffic channel basically. On the traffic channel, the UE provides special function for testing that is called Logical Test Interface and t... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.2 Reference Sensitivity Level | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.2.1 Definition and applicability | The reference sensitivity level <REFSENS> is the minimum mean power received at the UE antenna port at which the Bit Error Ratio (BER) shall not exceed a specific value
The requirements and this test apply to all types of UTRA for the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.2.2 Minimum Requirements | The BER shall not exceed 0,001 for the parameters specified in table 6.2.1.
Table 6.2.1: Test parameters for Reference Sensitivity Level
Operating Band
Unit
DPCH_Ec
<REFSENS>
<REFÎor>
I
dBm/3.84 MHz
-117
-106.7
II
dBm/3.84 MHz
-115
-104.7
III
dBm/3.84 MHz
-114
-103.7
IV
dBm/3.84 MHz
-117
-106.7
V
dBm/3.84 MHz
-115
-104... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.2.3 Test purpose | To verify that the UE BER shall not exceed 0,001 for the parameters specified in table 6.2.2.
The lack of the reception sensitivity decreases the coverage area at the far side from Node B. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.2.4.1 Initial conditions | Test environment: normal, TL/VL, TL/VH, TH/VL, TH/VH; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) Channel conditions are initially set up with received CPICH_RSCP >-85 dBm. The relativ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.2.4.2 Procedure | 1) Set and send continuously Up power control commands to the UE until the UE output power shall be maximum level.
2) Measure the BER of DCH received from the UE at the SS. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.2.5 Test requirements | The measured BER, derived in step 2), shall not exceed 0,001.
Table 6.2.2: Test parameters for Reference Sensitivity Level
Operating Band
Unit
DPCH_Ec
<REFSENS>
<REFÎor>
I
dBm/3.84 MHz
-116.3
-106
II
dBm/3.84 MHz
-114.3
-104
III
dBm/3.84 MHz
-113.3
-103
IV
dBm/3.84 MHz
-116.3
-106
V
dBm/3.84 MHz
-114.3
-104
VI
dBm/3.84... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.3 Maximum Input Level | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.3.1 Definition and applicability | This is defined as the maximum mean power received at the UE antenna port, which shall not degrade the specified BER performance.
The requirements and this test apply to all types of UTRA for the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.3.2 Minimum requirements | The BER shall not exceed 0.001 for the parameters specified in table 6.3.2.
The reference for this requirement is TS 25.101 [1] clause 7.4.1.
NOTE: Since the spreading factor is large (10log(SF)=21dB), the majority of the total input signal consists of the OCNS interference. The structure of OCNS signal is defined in c... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.3.3 Test purpose | To verify that the UE BER shall not exceed 0,001 for the parameters specified in table 6.3.3.
An inadequate maximum input level causes loss of coverage near the Node B |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.1.
2) RF parameters are set up according to table 6.3.3 and table E.3.3.
3) A call is set up according to the Generic call setup procedure spec... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.