hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.3.4.2 Procedure | 1) Set the power level of UE according to the table 6.3.3 or send the power control commands (1dB step size should be used.) to the UE until UE output power measured by Test System shall be kept at the specified power level with 1dB tolerance.
2) Measure the BER of DCH received from the UE at the SS. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.3.5 Test requirements | The measured BER, derived in step 1), shall not exceed 0,001.
Table 6.3.3: Test requirements for Maximum Input Level
Parameter
Level / Status
Unit
Îor
-25.7
dBm / 3,84MHz
-19
dB
UE transmitted mean power
20 (for Power class 3 and 3bis)
18 (for Power class 4)
dBm
NOTE: If the above Test Requirement differs from the Min... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.4 Adjacent Channel Selectivity (ACS) (Rel-99 and Rel-4) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.4.1 Definition and applicability | Adjacent Channel Selectivity (ACS) is a measure of a receiver's ability to receive a W-CDMA signal at its assigned channel frequency in the presence of an adjacent channel signal at a given frequency offset from the centre frequency of the assigned channel. ACS is the ratio of the receive filter attenuation on the assi... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.4.2 Minimum Requirements | For the UE of power class 3 and 4, the BER shall not exceed 0,001 for the parameters specified in table 6.4.1. This test condition is equivalent to the ACS value 33 dB.
Table 6.4.1: Test parameters for Adjacent Channel Selectivity for Release 99 and Release 4.
Parameter
Level / Status
Unit
DPCH_Ec
-103
dBm / 3,84 MHz
Î... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.4.3 Test purpose | To verify that the UE BER does not exceed 0,001 for the test parameters specified in table 6.4.2.
The lack of the ACS decreases the coverage area when other transmitter exists in the adjacent channel. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.4.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.4.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.4.
2) RF parameters are set up according to table 6.4.2.
3) A call is set up according to the Generic call setup procedure specified in TS34.10... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.4.4.2 Procedure | 1) Set the parameters of the interference signal generator as shown in table 6.4.2.
2) Set the power level of UE according to the table 6.4.2 or send the power control commands (1dB step size should be used.) to the UE until UE output power measured by Test System shall be kept at the specified power level with 1dB to... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.4.5 Test requirements | The measured BER, derived in step 1), shall not exceed 0,001.
Table 6.4.2: Test parameters for Adjacent Channel Selectivity for Release 99 and Release 4.
Parameter
Level / Status
Unit
DPCH_Ec
-103
dBm / 3,84 MHz
Îor
-92,7
dBm / 3,84 MHz
Ioac mean power (modulated)
-52
dBm
Fuw (offset)
-5 or +5
MHz
UE transmitted mean p... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5 Blocking Characteristics | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.1 Definition and applicability | The blocking characteristic is a measure of the receiver's ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels, without this unwanted input signal causing a degradation of the per... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.2 Minimum Requirements | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.2.1 Minimum Requirements (In-band blocking) | The BER shall not exceed 0,001 for the parameters specified in table 6.5.1. In-band blocking is defined for an unwanted interfering signal falling into the UE receive band or into the first 15 MHz below or above the UE receive band.
The normative reference for this requirement is TS 25.101 [1] clause 7.6.1.
Table 6.5.1... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.2.2 Minimum requirements (Out of-band blocking) | The BER shall not exceed 0.001 for the parameters specified in table 6.5.2. Out-of-band band blocking is defined for an unwanted interfering signal falling more than 15 MHz below or above the UE receive band. For table 6.5.2 in frequency range 1, 2 and 3, up to 24 exceptions are allowed for spurious response frequencie... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.2.3 Minimum requirements (Narrow band blocking) | The BER shall not exceed 0.001 for the parameters specified in table 6.5.3. This requirement is measure of a receiver's ability to receive a W-CDMA signal at its assigned channel frequency in the presence of an unwanted narrow band interferer at a frequency, which is less than the nominal channel spacing. The requireme... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.3 Test purpose | To verify that the UE BER does not exceed 0,001 for the parameters specified in table 6.5.4, table 6.5.5 and table 6.5.6. For Table 6.5.5 in frequency range 1, 2 and 3, up to (24) exceptions are allowed for spurious response frequencies in each assigned frequency channel when measured using a 1 MHz step size.
For Table... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.4.1 Initial conditions | For in-band case:
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
For out-of-band case:
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequency to be tested: 1 arbitrary frequency chosen from the low, mid or high range; see clause G.2.4.
For narrow-... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.4.2 Procedure | 1) Set the parameters of the CW generator or the interference signal generator as shown in table 6.5.4, 6.5.5 and table 6.5.6. For table 6.5.5, the frequency step size is 1 MHz.
2) Set the power level of UE according to the table 6.5.4, table 6.5.5, and table 6.5.6, or send the power control commands (1dB step size sho... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.5.5 Test requirements | For table 6.5.4, the measured BER, derived in step 2), shall not exceed 0.001. For table 6.5.5, the measured BER, derived in step 2) shall not exceed 0,001 except for the spurious response frequencies, recorded in step 3). The number of spurious response frequencies, recorded in step 3) shall not exceed 24 for frequenc... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.6 Spurious Response | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.6.1 Definition and applicability | Spurious response is a measure of the receiver's ability to receive a wanted signal on its assigned channel frequency without exceeding a given degradation due to the presence of an unwanted CW interfering signal at any other frequency at which a response is obtained i.e. for which the out of band blocking limit is not... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.6.2 Minimum Requirements | The BER shall not exceed 0,001 for the parameters specified in table 6.6.1.
The normative reference for this requirement is TS 25.101 [1] clause 7.7.1.
Table 6.6.1: Test parameters for Spurious Response
Parameter
Level
Unit
DPCH_Ec
<REFSENS> +3 dB
dBm / 3,84MHz
Îor
<REFÎor> +3 dB
dBm / 3,84MHz
Iblocking(CW)
-44
dBm
Fuw... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.6.3 Test purpose | To verify that the UE BER does not exceed 0,001 for the parameters specified in table 6.6.2.
The lack of the spurious response ability decreases the coverage area when other unwanted interfering signal exists at any other frequency. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.6.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.6.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequency to be tested: the same frequency as chosen in clause 6.5.4.1 for Blocking characteristics out-of-band case.
1) Connect the SS to the UE antenna connector as shown in figure A.6.
2) RF parameters are set up according to table 6.6.2.
3) A call is set up acc... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.6.4.2 Procedure | 1) Set the parameter of the CW generator as shown in table 6.6.2. The spurious response frequencies are determined in step 3) of clause 6.5.4.2.
2) Set the power level of UE according to the table 6.6.2 or send the power control commands (1dB step size should be used.) to the UE until UE output power measured by Test S... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.6.5 Test requirements | The measured BER, derived in step 3), shall not exceed 0,001.
Table 6.6.2: Test parameters for Spurious Response
Parameter
Level
Unit
DPCH_Ec
<REFSENS> +3 dB
dBm / 3,84MHz
Îor
<REFÎor> +3 dB
dBm / 3,84MHz
Iblocking(CW)
-44
dBm
Fuw
Spurious response frequencies
MHz
UE transmitted mean power
20 (for Power class 3 and 3bi... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.7 Intermodulation Characteristics | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.7.1 Definition and applicability | Third and higher order mixing of the two interfering RF signals can produce an interfering signal in the band of the desired channel. Intermodulation response rejection is a measure of the capability of the receiver to receive a wanted signal on its assigned channel frequency in the presence of two or more interfering ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.7.2 Minimum Requirements | The BER shall not exceed 0,001 for the parameters specified in table 6.7.1 and in table 6.7.2.
The normative reference for this requirement is TS 25.101 [1] clause 7.8.1 and clause 7.8.2.
Table 6.7.1: Test parameters for Intermodulation Characteristics
Parameter
Level
Unit
DPCH_Ec
<REFSENS> +3 dB
dBm / 3,84 MHz
Îor
<RE... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.7.3 Test purpose | To verify that the UE BER does not exceed 0,001 for the parameters specified in table 6.7.3 and in table 6.7.4.
The lack of the intermodulation response rejection ability decreases the coverage area when two or more interfering signals, which have a specific frequency relationship to the wanted signal, exist. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.7.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.7.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS to the UE antenna connector as shown in figure A.7.
2) RF parameters are set up according to table 6.7.3 and table 6.7.4.
3) A call is set up according to the Generic call setup procedure spec... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.7.4.2 Procedure | 1) Set the parameters of the CW generator and interference signal generator as shown in table 6.7.3 and in table 6.7.4.
2) Set the power level of UE according to the tables 6.7.3, and table 6.7.4 or send the power control commands (1dB step size should be used.) to the UE until UE output power measured by Test System s... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.7.5 Test requirements | The measured BER, derived in step 3), shall not exceed 0,001.
Table 6.7.3: Test parameters for Intermodulation Characteristics
Parameter
Level
Unit
DPCH_Ec
<REFSENS> +3 dB
dBm / 3.84 MHz
Îor
<REFÎor> +3 dB
dBm / 3.84 MHz
Iouw1 (CW)
-46
dBm
Iouw2 mean power (modulated)
-46
dBm
Fuw1 (offset)
10
-10
MHz
Fuw2 (offset)
20
-... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.8 Spurious Emissions | Editor’s note: For a transition period of two meeting cycles until RAN#70, the test requirements in version 11.6.0 of this specification is allowed to be used for this test. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.8.1 Definition and applicability | The spurious emissions power is the power of emissions generated or amplified in a receiver that appear at the UE antenna connector. The spurious emission is verified per antenna connector with the other(s) terminated.
The requirements and this test apply to all types of UTRA for the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.8.2 Minimum Requirements | The power of any narrow band CW spurious emission shall not exceed the maximum level specified in table 6.8.1, table 6.8.2 and 5.11.1b.
Table 6.8.1: General receiver spurious emission requirements
Frequency Band
Measurement
Bandwidth
Maximum level
Note
30 MHz f < 1 GHz
100 kHz
-57 dBm
1 GHz f 12,75 GHz
1 MHz
-47 ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.8.3 Test purpose | To verify that the UE spurious emission meets the specifications described in clause 6.8.5.
Excess spurious emissions increase the interference to other systems. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.8.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.8.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: low range, mid range, high range; see clause G.2.4.
1) Connect a spectrum analyzer (or other suitable test equipment) to the UE antenna connector as shown in figure A.8.
2) RF parameters are setup according to table E.3.2.2. Settings for t... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.8.4.2 Procedure | 1) Sweep the spectrum analyzer (or equivalent equipment) over a frequency range and measure the average power of spurious emission. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 6.8.5 Test requirements | It shall be verified that the RRC connection release at the end of the procedure described in 34.108 [3] clause 7.3.5.3 shall be completed successfully indicating that the UE has stayed in CELL_FACH state during the measurement of the spurious emissions.
The measured spurious emissions, derived in step 1), shall not ex... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.1 General | The performance requirements for the UE in this clause are specified for the measurement channels specified in annex C and table 7.1.1, the propagation conditions specified in clause 7.1.2 and the Down link Physical channels specified in annex D. Unless stated otherwise, DL power control is OFF. Unless otherwise stated... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.1.1 Measurement Configurations | It as assumed that fields inside DPCH have the same energy per PN chip. Also, if the power of S-CCPCH is not specified in the test parameter table, it should be set to zero. The power of OCNS should be adjusted that the power ratios (Ec/Ior) of all specified downlink channels add up to one.
Unless otherwise stated, the... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.1.2 Definition of Additive White Gaussian Noise (AWGN) Interferer | See clause D.1.1. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2 Demodulation in Static Propagation conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.1 Demodulation of Dedicated Channel (DCH) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.1.1 Definition and applicability | The receive characteristic of the Dedicated Channel (DCH) in the static environment is determined by the Block Error Ratio (BLER). BLER is specified for each individual data rate of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data rate, supported. The ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.1.2 Minimum requirements | For the parameters specified in table 7.2.1.1 the average downlink power ratio shall be below the specified value for the BLER shown in table 7.2.1.2. These requirements are applicable for TFCS size 16.
Table 7.2.1.1: DCH parameters in static propagation conditions
Parameter
Test 1
Test 2
Test 3
Test 4
Unit
Phase refe... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.1.3 Test purpose | To verify the ability of the receiver to receive a predefined test signal, representing a static propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a BLER not exceeding a specified value. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect the SS and an AWGN noise source to the UE antenna connector as shown in figure A.9. In case of UE-receive diversity connect according to figure A.26.
2. Set up a call according to the Generic call se... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.1.4.2 Procedures | 1. Measure BLER of DCH. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.1.5 Test requirements | For the parameters specified in table 7.2.1.3 the average downlink power ratio shall be below the specified value for the BLER shown in table 7.2.1.4. These requirements are applicable for TFCS size 16.
NOTE: The test case is executed with TFCS size 4 according to the Reference Measurement Channels defined in Annex C.... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.2 Demodulation of Dedicated Channel (DCH) when (DL_DCH_FET_Config) is configured by higher layers | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.2.1 Definition and applicability | The receive characteristic of the Dedicated Channel (DCH) in the static environment is determined by the Block Error Ratio (BLER). BLER is specified for each individual data rate of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data rate, supported. The ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.2.2 Minimum requirements | For the parameters specified in table 7.2.2.1 the average downlink power ratio shall be below the specified value for the BLER shown in table 7.2.2.2. These requirements are applicable for TFCS size 16.
Table 7.2.2.1: DCH parameters in static propagation conditions
Parameter
Unit
Test 1
Test 2
Test 3
Test 4
Phase refe... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.2.3 Test purpose | To verify the ability of the receiver to receive a predefined test signal, representing a static propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a BLER not exceeding a specified value with DL_DCH_FET_Config by higher layers. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect the SS and an AWGN noise source to the UE antenna connector as shown in figure A.9. In case of UE-receive diversity connect according to figure A.26.
2. Set up a call according to the Generic call se... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.2.4.2 Procedures | 1. Measure BLER of DCH. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.2.2.5 Test requirements | For the parameters specified in table 7.2.2.4 the average downlink power ratio shall be below the specified value for the BLER shown in table 7.2.2.5. These requirements are applicable for TFCS size 16.
NOTE: The test case is executed with TFCS size 4 according to the Reference Measurement Channels defined in Annex C.... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3 Demodulation of DCH in Multi-path Fading Propagation conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.1 Single Link Performance | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.1.1 Definition and applicability | The receive characteristics of the Dedicated Channel (DCH) in different multi-path fading environments are determined by the Block Error Ratio (BLER) values. BLER is measured for the each of the individual data rate specified for the DPCH. DCH is mapped into in Dedicated Physical Channel (DPCH).
The UE shall be tested ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.1.2 Minimum requirements | For the parameters specified in tables 7.3.1.1, 7.3.1.3, 7.3.1.5, 7.3.1.7 and 7.3.1.9 the average downlink power ratio shall be below the specified value for the BLER shown in tables 7.3.1.2, 7.3.1.4, 7.3.1.6, 7.3.1.8 and 7.3.1.10. These requirements are applicable for TFCS size 16.
Table 7.3.1.1: DCH parameters in mu... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.1.3 Test purpose | To verify the ability of the receiver to receive a predefined test signal, representing a multi-path fading propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a BLER not exceeding a specified value. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect the SS, multi-path fading simulator and an AWGN noise source to the UE antenna connector as shown in figure A.10. In case of UE-receive diversity connect according to figure A.21.
2. Set up a call ac... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.1.4.2 Procedures | 1. Measure BLER of DCH. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.1.5 Test requirements | For the parameters specified in tables 7.3.1.11, 7.3.1.13, 7.3.1.15, 7.3.1.17 and 7.3.1.19 the average downlink power ratio shall be below the specified value for the BLER shown in tables 7.3.1.12, 7.3.1.14, 7.3.1.16, 7.3.1.18 and 7.3.1.20. These requirements are applicable for TFCS size 16.
NOTE: The test case is exe... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.2 Single Link Performance when (DL_DCH_FET_Config) is configured by higher layers | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.2.1 Definition and applicability | The receive characteristics of the Dedicated Channel (DCH) in different multi-path fading environments are determined by the Block Error Ratio (BLER) values. BLER is measured for the each of the individual data rate specified for the DPCH. DCH is mapped into in Dedicated Physical Channel (DPCH).
The UE shall be tested ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.2.2 Minimum requirements | For the parameters specified in tables 7.3.2.1, 7.3.2.3, 7.3.2.5, 7.3.2.7 and 7.3.2.9 the average downlink power ratio shall be below the specified value for the BLER shown in tables 7.3.2.2, 7.3.2.4, 7.3.2.6, 7.3.2.8 and 7.3.2.10.
Table 7.3.2.1: DCH parameters in multi-path fading propagation conditions (Case 1)
Para... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.2.3 Test purpose | To verify the ability of the receiver to receive a predefined test signal, representing a multi-path fading propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a BLER not exceeding a specified value with DL_DCH_FET_Config by higher layers. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect the SS, multi-path fading simulator and an AWGN noise source to the UE antenna connector as shown in figure A.10. In case of UE-receive diversity connect according to figure A.21.
2. Set up a call ac... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.2.4.2 Procedures | 1. Measure BLER of DCH. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.3.2.5 Test requirements | For the parameters specified in tables 7.3.2.12, 7.3.2.14, 7.3.2.16, 7.3.2.18 and 7.3.2.20 the average downlink power ratio shall be below the specified value for the BLER shown in tables 7.3.2.11, 7.3.2.15, 7.3.2.17, 7.3.2.19 and 7.3.2.21.
NOTE: The test case is executed with TFCS size 4 according to the Reference Me... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.4 Demodulation of DCH in Moving Propagation conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.4.1 Single Link Performance | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.4.1.1 Definition and applicability | The receive single link performance of the Dedicated Channel (DCH) in dynamic moving propagation conditions are determined by the Block Error Ratio (BLER) values. BLER is measured for the each of the individual data rate specified for the DPCH. DCH is mapped into Dedicated Physical Channel (DPCH).
The UE shall be teste... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.4.1.2 Minimum requirements | For the parameters specified in table 7.4.1.1 the average downlink power ratio shall be below the specified value for the BLER shown in table 7.4.1.2.
Table 7.4.1.1: DCH parameters in moving propagation conditions
Parameter
Test 1
Test 2
Unit
Phase reference
P-CPICH
-1
dB
-60
dBm / 3,84 MHz
Information Data Rate
12,2
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.4.1.3 Test purpose | To verify the ability of the receiver to receive a predefined test signal, representing a moving propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a BLER not exceeding a specified value. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.4.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.4.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect the SS and an AWGN noise source to the UE antenna connector as shown in figure A.10. In case of UE-receive diversity connect according to figure A.21.
2. Set up a call according to the Generic call s... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.4.1.4.2 Procedures | 1. Measure BLER of DCH. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.4.1.5 Test requirements | For the parameters specified in table 7.4.1.3 the average downlink power ratio shall be below the specified value for the BLER shown in table 7.4.1.4.
Table 7.4.1.3: DCH parameters in moving propagation conditions
Parameter
Test 1
Test 2
Unit
Phase reference
P-CPICH
-0,4
dB
-60
dBm / 3,84 MHz
Information Data Rate
12,... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.5 Demodulation of DCH in Birth-Death Propagation conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.5.1 Single Link Performance | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.5.1.1 Definition and applicability | The receive single link performance of the Dedicated Channel (DCH) in dynamic birth-death propagation conditions are determined by the Block Error Ratio (BLER) values. BLER is measured for the each of the individual data rate specified for the DPCH. DCH is mapped into Dedicated Physical Channel (DPCH).
The UE shall be ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.5.1.2 Minimum requirements | For the parameters specified in table 7.5.1.1 the average downlink power ratio shall be below the specified value for the BLER shown in table 7.5.1.2.
Table 7.5.1.1: DCH parameters in birth-death propagation conditions
Parameter
Test 1
Test 2
Unit
Phase reference
P-CPICH
-1
dB
-60
dBm / 3,84 MHz
Information Data Rate
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.5.1.3 Test purpose | To verify the ability of the receiver to receive a predefined test signal, representing a birth-death propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a BLER not exceeding a specified value. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.5.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.5.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1. Connect the SS and an AWGN noise source to the UE antenna connector as shown in figure A.10. In case of UE-receive diversity connect according to figure A.21.
2. Set up a call according to the Generic call s... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.5.1.4.2 Procedures | 1. Measure BLER of DCH. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 7.5.1.5 Test requirements | For the parameters specified in table 7.5.1.3 the average downlink power ratio shall be below the specified value for the BLER shown in table 7.5.1.4.
Table 7.5.1.3: DCH parameters in birth-death propagation conditions
Parameter
Test 1
Test 2
Unit
Phase reference
P-CPICH
-0,4
dB
-60
dBm / 3,84 MHz
Information Data Rat... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.