hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.2 E-UTRA is of lower priority | Editor’s note: This Test case is incomplete for frequencies above 3GHz
• The Test system uncertainties applicable above 3GHz are undefined
• The Test Tolerances and Test Requirements applicable above 3GHz are undefined |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.2.1 Definition and applicability | The cell re-selection delay is defined as the time from a change of cell levels, to the moment when the UE camps on a new cell, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on the new cell.
The requirements and this test apply to Re... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.2.2 Minimum requirement | The cell re-selection delay shall be less than 21 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as: TevaluateEUTRA + TSI-EUTRA, where:
TevaluateEUTRA See Table 4.2 in section 4.2.2 of TS 25.133 [2].
TSI-EUTRA Maximum re... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.2.3 Test purpose | To verify that the UE meets the minimum requirement. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: see table K.2 in Annex K.
This scenario implies the presence of 1 UTRAN serving cell, and 1 E-UTRAN cell to be re-selected. The UE is requested to monitor neighbouring cells on 1 UTRAN carrier and 1 E-UTRAN carrier. Test parameters are giv... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.2.4.2 Procedure | 1) The SS activates cell 1 with T1 parameters defined in tables 8.2.5.2.4 and monitors cell 1 for random access requests from the UE.
2) The UE is switched on.
3) The SS and the UE shall perform a location / routing area update procedure on cell 1 and apply the cell 2 parameters with T1 defined in table 8.2.5.2.5. T1 s... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.2.4.3 Message contents | All messages indicated above shall use the same content as described in the default message content in TS 36.508 [33] clause 4.4 and 4.6 with the following exceptions:
SystemInformationBlockType19: for inter-RAT UTRA FDD - EUTRAN FDD is of lower priority cell re-selection
Derivation Path: TS 36.508 [33] clause 4.4.4.1,... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.2.5 Test requirements | Table 8.2.5.2.4: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 1)
Parameter
Unit
Cell 1 (UTRA)
T1
T2
UTRA RF Channel Number
Channel 1
CPICH_Ec/Ior
dB
-10
PCCPCH_Ec/Ior
dB
-12
SCH_Ec/Ior
dB
-12
PICH_Ec/Ior
dB
-15
OCNS_Ec/Ior
dB
-0.941
dB
11.90
-5.70
dBm/3,84 MHz
-70.10
CPICH_Ec/Io
dB
-10.27
-1... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.3 RSRQ based reselection when E-UTRA FDD is of higher priority | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.3.1 Definition and applicability | The cell re-selection delay is defined as the time from a change of cell levels, to the moment when the UE camps on a new cell, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on the new cell.
The requirements and this test apply to Re... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.3.2 Minimum requirement | The cell re-selection delay shall be less than 21 s. The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as: Thigher_priority_search + TevaluateEUTRA + TSI, where:
Thigher_priority_search See section 4.2.2 of TS 25.133 [2], where... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.3.3 Test purpose | To verify that the UE meets the minimum requirement. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: see table K.2 in Annex K.
The test scenario comprises two different cells, with cell 1 being the UTRA serving cell, cell 2 being the E-UTRA cell to be re-selected to. Test parameters are given in Tables 8.2.5.3.1, 8.2.5.3.2, 8.2.5.3.3. The... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.3.4.2 Procedure | 1) The SS activates cell 1 with T1 parameters defined in tables 8.2.5.3.4 and monitors cell 1 for random access requests from the UE.
2) The UE is switched on.
3) The SS and the UE shall perform a location / routing area update procedure on cell 1. T1 starts.
4) After T1 from the end of step 3, the parameters are chang... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.3.4.3 Message contents | All messages indicated above shall use the same content as described in the default message content in TS 36.508 [33] clause 4.4 and 4.6 with the following exceptions:
SystemInformationBlockType19: for inter-RAT UTRA FDD - RSRQ based reselection when E-UTRA FDD is of higher priority
Derivation Path: TS 36.508 [33] clau... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.2.5.3.5 Test requirements | Table 8.2.5.3.4: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 1)
Parameter
Unit
Cell 1 (UTRA)
T1
T2
T3
T4
UTRA RF Channel Number
Channel 1
CPICH_Ec/Ior
dB
-10
PCCPCH_Ec/Ior
dB
-12
SCH_Ec/Ior
dB
-12
PICH_Ec/Ior
dB
-15
OCNS_Ec/Ior
dB
-0.941
dB
13.8
13.8
13.8
13.8
dBm/3,84 MHz
‑70
CPICH_Ec/Io
d... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3 UTRAN Connected Mode Mobility | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.1 FDD/FDD Soft Handover | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.1.1 Definition and applicability | The active set update delay of the UE is defined as the time from the end of the last TTI containing an RRC message implying soft handover to the switch off of the old downlink DPCH.
The requirements and this test apply to the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.1.2 Minimum requirement | The active set update delay is defined as the time from when the UE has received the ACTIVE SET UPDATE message from UTRAN, or at the time stated through the activation time when to perform the active set update, to the time when the UE successfully uses the set of radio links stated in that message for power control.
T... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.1.3 Test purpose | To verify that the UE meets the minimum requirement. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.1.1.1 and 8.3.1.1.2 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A shall be used, and that CPICH ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.1.4.2 Procedure | 1) The RF parameters are set up according to T0 in table 8.3.1.1.2A.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4 without compressed mode parameters and test loop mode 2 is used. See TS 34.109 [4] for details regarding loopback test. 10 second... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.1.5 Test requirements | Table 8.3.1.1.2A: Cell specific test parameters for Soft handover (T0)
Parameter
Unit
Cell 1
Cell 2
T0
T0
CPICH_Ec/Ior
dB
-9.3
-9.3
PCCPCH_Ec/Ior
dB
-11.3
-11.3
SCH_Ec/Ior
dB
-11.3
-11.3
PICH_Ec/Ior
dB
-14.3
-14.3
DPCH_Ec/Ior
dB
Note1
N/A
OCNS_Ec/Ior
dB
Note2
-1.13
dB
0
-Inf
dBm/ 3.84 MHz
-70
CPICH_Ec/Io
dB
-12.3
-Inf
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2 FDD/FDD Hard Handover | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.1 FDD/FDD Hard Handover to intra-frequency cell | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.1.1 Definition and applicability | The hard handover delay of the UE is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission of the new uplink DPCCH.
The requirements and this test apply to the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.1.2 Minimum requirement | The interruption time shall be less than 110 ms in CELL_DCH state in the single carrier case. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95 %.
The hard handover delay Dhandover equals the RRC procedure delay defined in TS 25.331 clause 13.5.2 plus the i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.1.3 Test purpose | To verify that the UE meets the minimum requirement. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in tables 8.3.2.1.1 to 8.3.2.1.3 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A and 1B shall be used, and that... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.1.4.2 Procedure | 1) The RF parameters are set up according to T1 in table 8.3.2.1.3.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4. Data shall be sent on the DTCH throughout the call.
4) SS shall transmit a MEASUREMENT CONTROL message on cell 1.
5) 5 seconds aft... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.1.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90 % of the cases with a confidence level of 95 %.
Table 8.3.2.1.3: Test requirements for Handover to intra-frequency cell
Parameter
Unit
Cell 1
Cell 2
T1
T2
T3
T1
T2
T3
CPICH_Ec/Ior
dB
-9.3
-9.3
PCCPCH_Ec/Ior
dB
-11.3
-11.3
SCH_Ec/Ior
dB
-11... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.2 FDD/FDD Hard Handover to inter-frequency cell | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.2.1 Definition and applicability | The hard handover delay is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission of the new uplink DPCCH.
The requirements and this test apply to the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.2.2 Minimum requirement | The interruption time shall be less than 140 ms in CELL_DCH state in the dual carrier case. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95 %.
The hard handover delay Dhandover equals the RRC procedure delay defined in TS 25.331 clause 13.5.2 plus the int... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.2.3 Test purpose | To verify that the UE meets the minimum requirement. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in tables 8.3.2.2.1 to 8.3.2.2.3 below. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. In the measurement control informati... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.2.4.2 Procedure | 1) The RF parameters are set up according to T1 in table 8.3.2.2.3.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4 with Compressed mode parameters as in Table 8.3.2.2.1. Data shall be sent on the DTCH throughout the call.
4) SS shall transmit a ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.2.2.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.2.2.3: Test requirements for Handover to inter-frequency cell
Parameter
Unit
Cell 1
Cell 2
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
Channel 2
CPICH_Ec/Ior
dB
-9.2
-9.2
PCCP... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.3 FDD/TDD Handover | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.3.1 Definition and applicability | The hard handover delay is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission of the new uplink DPCH.
The requirements and this test apply to the combined FDD and TDD UE for Release 99 and Release 4 only. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.3.2 Minimum requirement | The hard handover delay shall be less than 110 ms in CELL_DCH state in the dual carrier case. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95 %.
The hard handover delay Dhandover equals the RRC procedure delay defined in TS 25.331 clause 13.5.2 plus the i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.3.3 Test purpose | To verify that the UE meets the minimum requirement. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Table 8.3.2.2.1 and 8.3.2.2.2 below. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. In the measurement control informati... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.3.4.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4 with Compressed mode parameters as in Table 8.3.2.2.1. Data shall be sent on the DTCH throughout the call.
4) SS shall transmit a MEASUREMENT CONTROL... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.3.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90% of the cases with a confidence level of 95 %.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 an... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.4 Inter-system Handover from UTRAN FDD to GSM | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.4.1 Definition and applicability | The UTRAN to GSM cell handover delay is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission on the channel of the new RAT.
The requirements and this test apply to the combined FDD and GSM UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.4.2 Minimum requirement | The UE shall begin to send access bursts on the new DCCH of the target cell less than 100 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
NOTE: The test requirement in this case is expressed as:
THandover delay = 90 ms (Table 8.3.4.1) + Toff... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.4.3 Test purpose | To verify that the UE meets the minimum requirement. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.4.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.4.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.4.3, 8.3.4.4 and 8.3.4.5 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 3C shall be used.. The test ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.4.4.2 Procedure | 1) The RF parameters for cell 1 are set up according to T1 in Table 8.3.4.4.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.7. For UEs that require compressed mode, the compressed mode parameters are configured as in the table 8.3.4.3. The compress... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.4.5 Test requirements | Table 8.3.4.6: Cell Specific Parameters for Handover UTRAN
to GSM cell case (cell 2), test requirements
Parameter
Unit
Cell 2 (GSM)
T1
T2, T3
Absolute RF Channel Number
BCCH ARFCN of cell A as defined in the initial conditions in clause 26.6.5.1 of TS 51.010-1 [25] for the GSM band under test.
BCCH ARFCN is 744 for FDD... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5 Cell Re-selection in CELL_FACH | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.1 One frequency present in neighbour lis and FACH measurement occasions configured | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.1.1 Definition and applicability | The cell re-selection delay is defined as the time between the occurrence of an event which will trigger Cell Reselection process and the moment in time when the UE starts sending the preambles on the PRACH for sending RRC CELL UPDATE message to the UTRAN.
The requirements and this test apply to the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.1.2 Minimum requirements | The cell re-selection delay shall be less than 1.6 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
If a cell has been detectable at least Tidentify,intra, the cell reselection delay in CELL_FACH state to a cell in the same frequency shall be less than
ms
where
TMeasurement... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.1.3 Test purpose | The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in the single carrier case |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.5.1.1 to 8.3.5.1.5. The UE is requested to monitor neighbouring cells on 1 carrier. The maximum repetition period of the relevant system info blocks that needs to be r... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.1.4.2 Procedure | 1) The SS activates cell 1-6 with RF parameters set up according to T1 in table 8.3.5.1.5.
2) The UE is switched on.
3) An RRC connection is set up according to the signalling sequence in the generic set-up procedure specified in TS 34.108 [3] subclause 7.3.5 to place the UE in the CELL_FACH state on Cell 2 and the SS ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.1.5 Test requirements | For the test to pass, the total number of successful attempts shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.5.1.5: Cell specific test requirements
for Cell Re-selection in CELL_FACH, one freq. in neighbour list
Parameter
Unit
Cell 1
Cell 2
Cell 3
Cell 4
Cell 5
Cell 6
T1
T2
T1
T2
T1
T2
T... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.2 Two frequencies present in the neighbour list and FACH measurement occasions configured | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.2.1 Definition and applicability | The cell re-selection delay is defined as the time between the occurrence of an event which will trigger Cell Reselection process and the moment in time when the UE starts sending the preambles on the PRACH for sending RRC CELL UPDATE message to the UTRAN.
The requirements and this test apply to the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.2.2 Minimum requirements | The cell re-selection delay shall be less than 1.9 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
If a cell has been detectable at least Tidentify,inter, the cell reselection delay in CELL_FACH state to a FDD cell on a different frequency shall be less than
ms
where
TMeas... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.2.3 Test purpose | The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in the single carrier case |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.5.2.1 to 8.3.5.2.5. The UE is requested to monitor neighbouring cells on 2 carriers. The maximum repetition period of the relevant system info blocks that needs to be ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.2.4.2 Procedure | 1) The RF parameters for cell 1 are set up according to T1 in table 8.3.5.2.5.
2) The UE is switched on.
3) An RRC connection is set up according to the signalling sequence in the generic set-up procedure specified in TS 34.108 [3] subclause 7.3.5 to place the UE in the CELL_FACH state on Cell 2 and the SS waits for th... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.2.5 Test requirements | For the test to pass, the total number of successful attempts shall be more than 90 % of the cases with a confidence level of 95 %.
Table 8.3.5.2.5: Cell specific test requirements for Cell re-selection in CELL_FACH state, two frequencies in neighbour list
Parameter
Unit
Cell 1
Cell 2
Cell 3
Cell 4
Cell 5
Cell 6
T1
T2
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.3 Cell Reselection to GSM | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.3.1 Definition and applicability | The cell re-reselection delay is defined as the time from the beginning of time period T2, to the moment when the UE starts to transmit the random access in Cell 2 (the GSM cell).
This requirements and this test apply to UE supporting FDD PS and GSM GPRS. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.3.2 Minimum requirements | The cell re-selection delay shall be less than 5.5 + TRA s.
The rate of correct reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed
ms
where:
Tidentify,GSM Specified in TS 25.133 [2] clause 8.4.2.5.2.1, here it is 2880 ms
Tmeasurement, GSM Specified in T... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.3.3 Test purpose | The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.5.3.1 to 8.3.5.3.5. This scenario implies the presence of 1 UTRAN serving cell, and 1 GSM cell to be re-selected. The UTRAN cell and the GSM cell are set to belong to ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.3.4.2 Procedure | 1) The SS activates cell 1-2 with RF parameters set up according to T1 in tables 8.3.5.3.6 and 8.3.5.3.7.
2) The UE is switched on.
3) An RRC connection is set up according to the signalling sequence in the generic set-up procedure specified in TS 34.108 [3] subclause 7.3.8 to place the UE in CELL_FACH and the SS waits... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.3.5 Test requirements | Table 8.3.5.3.6: Cell re-selection UTRAN to GSM cell case (cell 1) Test Requirements
Parameter
Unit
Cell 1 (UTRA)
T1
T2
UTRA RF Channel Number
Channel 1
CPICH_Ec/Ior
dB
-9.9
-10.1
PCCPCH_Ec/Ior
dB
-12
SCH_Ec/Ior
dB
-12
PICH_Ec/Ior
dB
-15
S-CCPCH_Ec/Ior
dB
-12
OCNS_Ec/Ior
dB
-1.309
-1.282
dB
0.3
-5.3
dBm/3.84 MHz
‑70
CP... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.4 Cell Reselection during an MBMS session, two frequencies present in neighbour list | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.4.1 Definition and applicability | The purpose of this test is to verify the requirement for the cell identification for UEs in an MBMS PTM session and the required functionality on measurement occasions by use of a cell re-selection test case.
The requirements and this test apply to release 6 and later releases for FDD UE that supports MBMS. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.4.2 Minimum requirements | The UE is requested to receive the MBMS service and monitor neighbouring cells on 2 carriers. The maximum repetition period of the relevant system info blocks that needs to be received by the UE to camp on a cell shall be 1280 ms.
The cell re-selection delay shall be less than 1.9s.
During T1 and T2 the MTCH SDU ER sha... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.4.3 Test purpose | The purpose of this test is to verify the requirement for the cell identification for UEs in an MBMS PTM session and the required functionality on measurement occasions by use of a cell re-selection test case. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.4.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.4.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
For the test parameters given in tables 8.3.5.4.4.1, 8.3.5.4.4.2, 8.3.5.4.4.3, 8.3.5.4.4.4, 8.3.5.4.4.5 and 8.3.5.4.4.6. The UE is requested to receive the MBMS service and monitor neighbouring cells on 2 carri... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.4.4.2 Procedure | Initiation
1) The SS activates cell 1-2 with T1 defined parameters in table 8.3.5.4.5 and monitors cell 2 for random access requests from the UE. The SS broadcast the cell reselection parameters according to table 8.3.5.4.5.
2) The UE is switched on. The UE has selected the broadcast service provided by the SS (include... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.4.5 Test requirements | Table 8.3.5.4.5: Cell specific test requirements for Cell re-selection in CELL_FACH state
Parameter
Unit
Cell 1
Cell 2
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
Channel 2
CPICH_Ec/Ior
dB
-9
-9
PCCPCH_Ec/Ior
dB
-11
-11
SCH_Ec/Ior
dB
-11
-11
PICH_Ec/Ior
dB
-14
-14
S-CCPCH_1_Ec/Ior
dB
-11
-11
S-CCPCH_2_Ec/Ior
dB
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5 UTRAN to E-UTRA Cell Reselection | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.1 Reselection to E-UTRA FDD when HS-DSCH DRX is configured (E-UTRA has higher priority) | - This Test case is incomplete for frequencies above 3GHz:
o The Test system uncertainties applicable above 3GHz are undefined.
o The Test Tolerances and Test Requirements applicable above 3GHz are undefined. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.1.1 Definition and applicability | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2 (E-UTRA).
The requirements and this test appl... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.1.1 Minimum requirements | The cell re-selection delay shall be less than 66 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as:
, where:
TSI = the maximum time allowed acquire system information from an E-UTRAN cell, 1280msec [34].
TRA = the addi... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.1.3 Test purpose | The purpose of this test is to verify the requirement for the UTRA FDD to E-UTRA FDD inter-RAT cell reselection delay. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test scenario comprises two different cells, with cell 1 being the UTRA serving cell and cell 2 being the E-UTRA cell to be re-selected to. Test parameters are given in Tables 8.3.5.5.1.1 to 8.3.5.5.1.3. Th... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.