hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.1.4.2 Procedure | 1) The SS activates cell 1 and 2 with T1 defined parameters in tables 8.3.5.5.1.4 and 8.3.5.5.1.5 and monitors cell 1 and 2 for random access requests from the UE.
2) The UE is switched on.
3) An RRC connection is set up according to the signalling sequence in the generic set-up procedure specified in TS 34.108 [3] cla... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.1.5 Test requirements | For the test to pass, the total number of successful attempts shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.5.5.3.4: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 1)
Parameter
Unit
Cell 1 (UTRA)
T1
T2
UTRA RF Channel Number
Channel 1
CPICH_Ec/Ior
dB
-10
PCCPCH... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.2 Reselection to E-UTRA FDD when HS-DSCH DRX is configured (E-UTRA has lower priority) | - This Test case is incomplete for frequencies above 3GHz:
- The Test system uncertainties applicable above 3GHz are undefined.
- The Test Tolerances and Test Requirements applicable above 3GHz are undefined. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.2.1 Definition and applicability | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2 (E-UTRA).
The requirements and this test appl... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.2.1 Minimum requirements | The cell re-selection delay shall be less than 5.7s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
, where:
TSI = the maximum time allowed acquire system information from a E-UTRAN cell, 1280msec [34].
TRA = the additional delay caused by the random access procedure, 30ms... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.2.3 Test purpose | The purpose of this test is to verify the requirement for the UTRA FDD to E-UTRA FDD inter-RAT cell reselection delay. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
This scenario implies the presence of 1 UTRAN serving cell, and 1 E-UTRAN cell to be re-selected. The UE is requested to monitor neighbouring cells on 1 UTRAN carrier and 1 E-UTRAN carrier. Test parameters are ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.2.4.2 Procedure | 1) The SS activates cell 1 and 2 with T1 defined parameters in tables 8.3.5.5.2.4 and 8.3.5.5.2.5 and monitors cell 1 and 2 for random access requests from the UE.
2) The UE is switched on.
3) An RRC connection is set up according to the signalling sequence in the generic set-up procedure specified in TS 34.108 [3] sub... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.2.5 Test requirements | For the test to pass, the total number of successful attempts shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.5.5.2.4: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 1)
Parameter
Unit
Cell 1 (UTRA)
T1
T2
UTRA RF Channel Number
Channel 1
CPICH_Ec/Ior
dB
-10
PCCPCH... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.3 Reselection to E-UTRA FDD when HS-DSCH 2nd DRX is configured (E-UTRA has higher priority) | Editor's notes: This Test case is incomplete for frequencies above 3GHz:
o The Test system uncertainties applicable above 3GHz are undefined.
o The Test Tolerances and Test Requirements applicable above 3GHz are undefined. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.3.1 Definition and applicability | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2 (E-UTRA).
The requirements and this test appl... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.3.1 Minimum requirements | The cell re-selection delay shall be less than 66 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as:
, where:
TSI = the maximum time allowed acquire system information from a E-UTRAN cell, 1280msec [34].
TRA = the addit... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.3.3 Test purpose | The purpose of this test is to verify the requirement for the UTRA FDD to E-UTRA FDD inter-RAT cell reselection delay. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test scenario comprises two different cells, with cell 1 being the UTRA serving cell and cell 2 being the E-UTRA cell to be re-selected to. Test parameters are given in Tables 8.3.5.5.3.1 to 8.3.5.5.3.3. Th... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.3.4.2 Procedure | 1) The SS activates cell 1 and 2 with T1 defined parameters in tables 8.3.5.5.3.4 and 8.3.5.5.3.5 and monitors cell 1 and 2 for random access requests from the UE.
2) The UE is switched on.
3) An RRC connection is set up according to the signalling sequence in the generic set-up procedure specified in TS 34.108 [3] cla... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.4 Reselection to E-UTRA TDD when HS-DSCH DRX is configured (E-UTRA has higher priority) | - This Test case is incomplete for frequencies above 3GHz:
o The Test system uncertainties applicable above 3GHz are undefined.
o The Test Tolerances and Test Requirements applicable above 3GHz are undefined. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.4.1 Definition and applicability | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2 (E-UTRA).
The requirements and this test appl... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.4.1 Minimum requirements | The cell re-selection delay shall be less than 66 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as:
, where:
TSI = the maximum time allowed acquire system information from an E-UTRAN cell, 1280msec [34].
TRA = the addi... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.4.3 Test purpose | The purpose of this test is to verify the requirement for the UTRA FDD to E-UTRA TDD inter-RAT cell reselection delay. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.4.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.4.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test scenario comprises two different cells, with cell 1 being the UTRA serving cell and cell 2 being the E-UTRA cell to be re-selected to. Test parameters are given in Tables A8.3.5.5.4.1 to 8.3.5.5.4.3. T... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.4.4.2 Procedure | Same as in clause 8.3.5.5.1.4.2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.4.5 Test requirements | For the test to pass, the total number of successful attempts shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.5.5.4.4: Cell specific test parameters for UTRAN to E-UTRA TDD cell reselection (cell 1)
Parameter
Unit
Cell 1 (UTRA)
T1
T2
UTRA RF Channel Number
Channel 1
CPICH_Ec/Ior
dB
-10
PC... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.5 Reselection to E-UTRA TDD when HS-DSCH DRX is configured (E-UTRA has lower priority) | - This Test case is incomplete for frequencies above 3GHz:
o The Test system uncertainties applicable above 3GHz are undefined.
o The Test Tolerances and Test Requirements applicable above 3GHz are undefined. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.5.1 Definition and applicability | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2 (E-UTRA).
The requirements and this test appl... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.5.1 Minimum requirements | The cell re-selection delay shall be less than 5.7 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
, where:
TSI = the maximum time allowed acquire system information from a E-UTRAN cell, 1280msec [34].
TRA = the additional delay caused by the random access procedure, 30m... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.5.3 Test purpose | The purpose of this test is to verify the requirement for the UTRA FDD to E-UTRA FDD inter-RAT cell reselection delay. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.5.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.5.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
This scenario implies the presence of 1 UTRAN serving cell, and 1 E-UTRAN cell to be re-selected. The UE is requested to monitor neighbouring cells on 1 UTRAN carrier and 1 E-UTRAN carrier. Test parameters are ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.5.4.2 Procedure | Same as clause 8.3.5.5.2.4.2 |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.5.5 Test requirements | For the test to pass, the total number of successful attempts shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.5.5.5.4: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 1)
Parameter
Unit
Cell 1 (UTRA)
T1
T2
UTRA RF Channel Number
Channel 1
CPICH_Ec/Ior
dB
-10
PCCPCH... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.6 Reselection to E-UTRA TDD when HS-DSCH 2nd DRX is configured (E-UTRA has higher priority) | - This Test case is incomplete for frequencies above 3GHz:
o The Test system uncertainties applicable above 3GHz are undefined.
o The Test Tolerances and Test Requirements applicable above 3GHz are undefined. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.6.1 Definition and applicability | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2 (E-UTRA).
The requirements and this test appl... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.6.2 Minimum requirements | The cell re-selection delay shall be less than 66 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as:
, where:
TSI = the maximum time allowed acquire system information from a E-UTRAN cell, 1280msec [34].
TRA = the additio... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.6.3 Test purpose | The purpose of this test is to verify the requirement for the UTRA FDD to E-UTRA FDD inter-RAT cell reselection delay. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.6.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.6.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test scenario comprises two different cells, with cell 1 being the UTRA serving cell and cell 2 being the E-UTRA cell to be re-selected to. Test parameters are given in Tables 8.3.5.5.6.1 to 8.3.5.5.6.3. Th... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.6.4.2 Procedure | Same as clause 8.3.5.5.3.4.2 |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.5.5.6.5 Test requirements | For the test to pass, the total number of successful attempts shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.5.5.6.4: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 1)
Parameter
Unit
Cell 1 (UTRA)
T1
T2
UTRA RF Channel Number
Channel 1
CPICH_Ec/Ior
dB
-10
PCCPCH... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6 Cell Re-selection in CELL_PCH | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.1 One frequency present in the neighbour list | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.1.1 Definition and applicability | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change makes the UE camp on a new cell, and starts to send preambles on the PRACH for the CELL UPDATE message with cause value "cell reselection" in the new cell.
The requirements and this test apply to the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.1.2 Minimum requirements | The cell re-selection delay shall be less than 8 s with a DRX cycle length of 1.28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95 %.
NOTE: The cell re-selection delay can be expressed as: TevaluateFDD + TSI, where:
TevaluateFDD
See table 4.1 i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.1.3 Test purpose | To verify that the UE meets the minimum requirements and is capable of camping on to a new cell, within the required time, when the preferred cell conditions change. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
This scenario implies the presence of 1 carrier and 6 cells as given in tables 8.3.6.1.1 to 8.3.6.1.3. The UE is requested to monitor neighbouring cells on 1 carrier. The maximum repetition period of the releva... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.1.4.2 Procedure | 1) The SS activates cell 1-6 with T1 defined parameters in table 8.3.6.1.3 and monitors cell 1 and 2 for random access requests from the UE.
2) The UE is switched on.
3) An RRC connection is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.3.3 to place the UE in the CELL_PCH state... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.1.5 Test requirements | For the test to pass, the total number of successful attempts shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.6.1.3: Cell specific test requirements for Cell re-selection
in CELL_PCH state, one freq. in neighbour list
Parameter
Unit
Cell 1
Cell 2
Cell 3
Cell 4
Cell 5
Cell 6
T1
T2
T1
T2
T1... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.2 Two frequencies present in the neighbour list | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.2.1 Definition and applicability | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change makes the UE camp on a new cell, and starts to send preambles on the PRACH for the CELL UPDATE message with cause value "cell reselection" in the new cell.
The requirements and this test apply to the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.2.2 Minimum requirement | The cell re-selection delay shall be less than 8 s with a DRX cycle length of 1.28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95 %.
NOTE: The cell re-selection delay can be expressed as: TevaluateFDD + TSI, where:
TevaluateFDD
See table 4.1 i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.2.3 Test purpose | To verify that the UE meets the minimum requirement and is capable of camping on to a new cell, within the required time, when the preferred cell conditions change. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
This scenario implies the presence of 2 carriers and 6 cells as given in tables 8.3.6.2.1 to 8.3.6.2.3. The UE is requested to monitor neighbouring cells on 2 carriers. The maximum repetition period of the rele... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.2.4.2 Procedure | 1) The SS activates cell 1-6 with T1 defined parameters in table 8.3.6.2.3 and monitors cell 1 and 2 for random access requests from the UE.
2) The UE is switched on.
3) A RRC connection is set up according the generic set-up procedure specified in TS 34.108 [3] subclause 7.3.3 to place the UE in CELL_PCH state on cell... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.2.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.6.2.3: Cell specific test requirements for Cell re-selection in CELL_PCH state, two frequencies in neighbour list
Parameter
Unit
Cell 1
Cell 2
Cell 3
Cell 4
Cell 5
Cell 6
T1
T2
T1
T2... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.3 Cell re-selection during an MBMS session, one UTRAN inter-frequency and 2 GSM cells present in the neighbour list | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.3.1 Definition and applicability | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change makes the UE camp on a new cell, and starts to send preambles on the PRACH for the CELL UPDATE message with cause value "cell reselection" in the new cell.
The requirements and this test apply to a Release 6 a... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.3.2 Minimum requirement | The cell re-selection delay is defined as the time from the beginning of time period T3, to the moment when the UE camps on Cell 3, and starts to send the RR Channel Request message for location update to Cell 3.
The cell re-selection delay shall be less than 2.75 s + TBCCH, where TBCCH is the maximum time allowed to r... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.3.3 Test purpose | To verify that the UE meets the minimum requirement and is capable of camping on to a new cell, within the required time, when the preferred cell conditions change. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
This scenario implies the presence of 1 UTRAN serving cell, 1 UTRAN inter-frequency cell and 2 GSM cells of which one is to be re-selected. The UE is requested to monitor neighbour cells on 2 UMTS carriers (Cha... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.3.4.2 Procedure | Initiation
1) Initiate the variables N_UEOK, N_UEOK_ACC, N_SS_ACC to 0.
2) The SS activates cell 1 to 4 with T1 defined parameters in tables 8.3.6.3.6 and 8.3.6.3.7 and monitors cell 2 and 3 for random access requests from the UE. The SS broadcast the cell reselection parameters according to tables 8.3.6.3.6 and 8.3.6.... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.6.3.5 Test requirements | For the test to pass, the following need to be fulfilled:
- the SDU error rate during T1 and T2 (SDU_ER_ACC) shall not exceed 4.0 %,
- the total number of successful tests of the cell re-selection delay requirement shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.6.3.6: Cell specific test ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7 Cell Re-selection in URA_PCH | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.1 One frequency present in the neighbour list | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.1.1 Definition and applicability | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change makes the UE camp on a new cell, and starts to send preambles on the PRACH for the URA UPDATE message with cause value "URA reselection" in the new cell.
The requirements and this test apply to the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.1.2 Minimum requirement | The cell re-selection delay shall be less than 8 s with a DRX cycle length of 1.28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95 %.
NOTE: The cell re-selection delay can be expressed as: TevaluateFDD + TSI, where:
TevaluateFDD
See table 4.1 i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.1.3 Test purpose | To verify that the UE meets the minimum requirement and is capable of camping on to a new cell, within the required time, when the preferred cell conditions change. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
This scenario implies the presence of 1 carrier and 6 cells as given in tables 8.3.7.1.1 to 8.3.7.1.3. The UE is requested to monitor neighbouring cells on 1 carrier. The maximum repetition period of the releva... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.1.4.2 Procedure | 1) The SS activates cell 1-6 with T1 defined parameters in table 8.3.7.1.3 and monitors cell 1 and 2 for random access requests from the UE.
2) The UE is switched on.
3) An RRC connection is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.3.3 to place the UE in the URA_PCH state... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.1.5 Test requirements | For the test to pass, the total number of successful attempts shall be more than 90% with a confidence level of 95 % of the cases.
Table 8.3.7.1.3: Cell specific test requirements for Cell re-selection in URA_PCH state,
one freq. in neighbour list
Parameter
Unit
Cell 1
Cell 2
Cell 3
Cell 4
Cell 5
Cell 6
T1
T2
T1
T2
T1
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.2 Two frequencies present in the neighbour list | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.2.1 Definition and applicability | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change makes the UE camp on a new cell, and starts to send preambles on the PRACH for the URA UPDATE message with cause value "URA reselection" in the new cell.
The requirements and this test apply to the FDD UE. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.2.2 Minimum requirement | The cell re-selection delay shall be less than 8 s with a DRX cycle length of 1.28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95 %.
NOTE: The cell re-selection delay can be expressed as: TevaluateFDD + TSI, where:
TevaluateFDD
See table 4.1 i... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.2.3 Test purpose | To verify that the UE meets the minimum requirement and is capable of camping on to a new cell, within the required time, when the preferred cell conditions change. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
This scenario implies the presence of 2 carriers and 6 cells as given in tables 8.3.7.2.1 to 8.3.7.2.3. The UE is requested to monitor neighbouring cells on 2 carriers. The maximum repetition period of the rele... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.2.4.2 Procedures | 1) The SS activates cell 1-6 with T1 defined parameters in table 8.3.7.2.3 and monitors cell 1 and 2 for random access requests from the UE.
2) The UE is switched on.
3) An RRC connection is set up according the generic set-up procedure specified in TS 34.108 [3] subclause 7.3.3 to place the UE in URA_PCH state on cell... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.7.2.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90% of the cases with a confidence level of 95%.
Table 8.3.7.2.3: Cell specific test requirements for Cell re-selection in URA_PCH state,
two freqs. in neighbour list
Parameter
Unit
Cell 1
Cell 2
Cell 3
Cell 4
Cell 5
Cell 6
T1
T2
T1
T2
T1
T2
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.8 Serving HS-DSCH cell change | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.8.1 Definition and applicability | When the UE receives a RRC message implying HS-DSCH cell change with the activation time "now" or earlier than RRC procedure delay seconds from the end of the last TTI containing the RRC command, the UE shall be ready to receive the HS-SCCH channel from the new cell within Dcell_change seconds from the end of the last ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.8.2 Minimum requirement | The UE shall start to transmit the CQI to cell 2 based on the quality of cell 2 less than 74 ms from the beginning of time period T4.
The UE shall also be able to start to receive the first HS-SCCH message from cell 2 less than 74 ms from the beginning of time period T4 and transmit the ACK or NAK which corresponds to ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.8.3 Test purpose | The purpose of this test is to verify the requirement for the delay when performing the serving HS-DSCH cell change in CELL_DCH state specified in section 8.3.8.2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.8.4 Method of test | The test parameters are given in Table 8.3.8.1, 8.3.8.1a, and 8.3.8.2 below. The test consists of 4 successive time periods, with a time duration of T1, T2, T3 and T4 respectively. At the start of time duration T1 the UE have cell 1 and cell 2 in active set and cell 1 as the serving HS-DSCH cell.
Data shall be transmit... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.8.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS (node B emulator) and fader and AWGN noise source to the UE antenna connector as shown in figure A.14.
2) Set up an HSDPA call according to TS 34.108 [3] clause 7.3.6 with levels according to ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.8.4.2 Procedure | 1) Turn on cell 2 and set the levels for both cells according to T1 in table 8.3.8.3.
2) SS shall send a MEASUREMENT CONTROL message (event 1A, 1B)
3) SS shall send a MEASUREMENT CONTROL message (event 1D)
4) UE shall send a MEASUREMENT REPORT message triggered by event 1A containing the CFN-SFN observed time differenc... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.8.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.8.2a: Cell specific test parameters for serving HS-DSCH cell change, initial conditions
Parameter
Unit
Cell 1
Cell 2
T0
T0
UTRA RF Channel Number
Channel 1
Channel 1
CPICH_Ec/Ior
dB
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.9 Enhanced Serving HS-DSCH cell change | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.9.1 Definition and applicability | The enhanced serving HS-DSCH cell change procedure is initiated from UTRAN either with a RRC message that implies a change of the serving HS-DSCH cell or through an HS-SCCH order sent on the target cell (target cell is the cell which becomes the serving cell after the enhanced serving HS-DSCH cell change procedure).
Th... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.9.2 Minimum requirement | When the UE receives an HS-SCCH order from the target cell that implies enhanced HS-DSCH serving cell change:
- if the activation time is not equal to "now", the UE shall be ready to receive the full configured HS-SCCH set from the target cell within MAX{40 ms, activation time – the end of the TTI containing the HS-SCC... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.9.3 Test purpose | The purpose of this test is to verify the requirement for the delay when performing the enhanced serving HS-DSCH cell change in CELL_DCH state specified in section 8.3.9.2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.9.4 Method of test | The test parameters are given in Table 8.3.9.1 and 8.3.9.2 below. The test consists of 4 successive time periods, with time durations of T1, T2, T3 and T4 respectively. At the start of time duration T1 the UE has cell 1 and cell 2 in the active set and cell 1 as the serving HS-DSCH cell. Target cell preconfiguration is... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.9.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS (node B emulator) and fader and AWGN noise source to the UE antenna connector as shown in figure A.14.
2) Set up an HSDPA call according to TS 34.108 [3] clause 7.3.6 with levels according to ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.9.4.2 Procedure | 1) T1 starts
2) SS shall send a MEASUREMENT CONTROL message (event 1D)
3) After 5 seconds from the beginning of T1, the SS shall switch the power settings from T1 to T2 according to the parameters defined in table 8.3.9.3.
4) During time period T2, UE shall transmit a MEASUREMENT REPORT message (intra frequency) trig... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.9.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90% of the cases with a confidence level of 95 %.
Table 8.3.9.3: Cell specific test parameters for enhanced serving HS-DSCH cell change
Parameter
Unit
Cell 1
Cell 2
T1
T2
T3
T4
T1
T2
T3
T4
UTRA RF Channel Number
Channel 1
Channel 1
CPICH_Ec/I... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.3.10 System information acquisition for CSG cell |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.