hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.5.1.4.2 Procedure | 1. A call is set up with Cell 1 according to the Generic call setup procedure specified in TS 34.108 [3] subclause 7.3.4 without Compressed mode. The test parameters are set up according to table 8.5.1.2.
2. After a connection is set up with cell 1, the test system shall measure the UE transmit timing offset with respe... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.5.1.5 Test requirements | Table 8.5.1.2: Test parameters for UE Transmit Timing requirements
Parameter
Unit
Level
DPCH_Ec/ Ior, Cell 1 and Cell 2
dB
-13.4
CPICH_Ec/ Ior, Cell 1 and Cell 2
dB
-9.9
PCCPH_Ec/ Ior, Cell 1 and Cell 2
dB
-12
SCH_Ec/ Ior, Cell 1 and Cell 2
dB
-12
PICH_Ec/ Ior, Cell 1 and Cell 2
dB
-15
OCNS_Ec/ Ior, Cell 1 and Cell 2
d... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6 UE Measurements Procedures | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1 FDD intra frequency measurements | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.1 Event triggered reporting in AWGN propagation conditions (R99) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.1.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This mea... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.1.2 Minimum requirements | The UE shall be able to identify and decode the SFN of a new detectable cell belonging to the monitored set within
A cell shall be considered detectable when CPICH Ec/Io > -20 dB, SCH_Ec/Io > -20 dB for at least one channel tap and SCH_Ec/Ior is equally divided between primary synchronisation code and secondary synchro... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.1.3 Test purpose | To verify that the UE meets the minimum requirements. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in tables 8.6.1.1.1 to 8.6.1.1.3 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A and 1B shall be used and that ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.1.4.2 Procedure | 1. The RF parameters are set up according to T1 in table 8.6.1.1.3, with cell 1 active.
2. The UE is switched on.
3. A call is set up according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The scrambling code is set to Cell2.
4. SS shall transmit a MEASUREMENT CONTROL message. T1 starts.
5. After ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.1.5 Test requirements | For the test to pass, the total number of successful tests shall be at least 90%, of the cases with a confidence level of 95%. For the overall outcome of the test to be considered a pass, the counters for 1A events and for 1B events shall independently indicate a pass result.
Table 8.6.1.1.3: Test requirements for Eve... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.2 Event triggered reporting of multiple neighbours in AWGN propagation condition (R99) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.2.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This mea... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.2.2 Minimum requirements | The requirements are the same as in sub clause 8.6.1.1.2.
The normative reference for these requirements is TS 25.133 [2] clauses 8.1.2.2 and A.8.1.2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.2.3 Test purpose | To verify that the UE meets the minimum requirements. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The initial test parameters are given in table 8.6.1.2.4.
Table 8.6.1.2.1: Cell specific initial test parameters for Event triggered reporting
of multiple neighbours in AWGN propagation conditions
Parameter
Uni... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.2.4.2 Procedure | 1) The RF parameters are set up according to T0 in table 8.6.1.2.4.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The scrambling code is set to Cell2 and Cell3.
4) SS shall transmit the initial MEASUREMENT CONTROL message.
5) 5 seconds after s... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.2.5 Test requirements | For the test to pass, the total number of successful tests shall be at least 90%, of the cases with a confidence level of 95%. For the overall outcome of the test to be considered a pass, the counters for 1A events and for 1B events and for 1C events shall independently indicate a pass result.
Table 8.6.1.2.4: Initial ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.3 Event triggered reporting of two detectable neighbours in AWGN propagation condition (R99) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.3.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This mea... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.3.2 Minimum requirements | The requirements are the same as in sub clause 8.6.1.1.2.
The normative reference for these requirements is TS 25.133 [2] clauses 8.1.2.2 and A.8.1.3. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.3.3 Test purpose | To verify that the UE meets the minimum requirements. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The initial test parameters are given in table 8.6.1.3.1.
Table 8.6.1.3.1: Cell specific initial test parameters for Event triggered reporting
of two detectable neighbours in AWGN propagation condition
Paramete... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.3.4.2 Procedure | 1) The RF parameters are set up according to T0 in table 8.6.1.3.4.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The scrambling code is set to Cell2 and Cell3.
4) SS shall transmit a MEASUREMENT CONTROL message. T0 starts.
5) After 10 seconds... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.3.5 Test requirements | For the test to pass, the total number of successful tests shall be at least 90% of the cases with a confidence level of 95%. For the overall outcome of the test to be considered a pass, the counters for 1A events and for 1B events shall independently indicate a pass result.
Table 8.6.1.3.4: Initial test parameters for... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.4 Void | 8.6.1.4A Correct reporting of neighbours in fading propagation condition (Rel-4 and later)
8.6.1.4A.1 Definition and applicability
In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.5 Event triggered reporting of multiple neighbour cells in Case 1 fading condition | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.5.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This mea... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.5.2 Minimum requirements | The requirements are the same as in sub clause 8.6.1.1A.2.
The normative reference for these requirements is TS 25.133 [2] clauses 8.1.2.2 and A.8.1.5. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.5.3 Test purpose | To verify that the UE meets the minimum requirements. The test is performed in Case 1 fading propagation conditions.
NOTE : The test case covers only the continuous uplink DPCCH transmission scenario. Hence the test case is effectively the same for all UE releases. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.5.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.5.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.6.1.5.1 and 8.6.1.5.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A shall be used and "CFN-SFN-Observed ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.5.4.2 Procedure | 1) The RF parameters are set up according to T1 in table 8.6.1.5.1.
2) The UE is switched on.
3) A call is set up with Cell 2 in AWGN conditions, according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The scrambling codes are set to Cell1.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) The... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.5.5 Test requirements | For the test to pass, the total number of successful tests shall be at least 90% of the cases with a confidence level of 95%. For the overall outcome of the test to be considered a pass, the counters for Event 1A shall independently indicate a pass result.
Table 8.6.1.5.3: Test requirements for Cell specific test param... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.6 Event triggered reporting of multiple neighbour cells in Case 3 fading condition | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.6.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This mea... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.6.2 Minimum requirements | The requirements are the same as in sub clause 8.6.1.1A.2.
The normative reference for these requirements is TS 25.133 [2] clauses 8.1.2.2 and A.8.1.6. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.6.3 Test purpose | To verify that the UE meets the minimum requirements. The test is performed in Case 3 fading propagation conditions.
NOTE : The test case covers only the continuous uplink DPCCH transmission scenario. Hence the test case is effectively the same for all UE releases. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.6.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.6.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.6.1.5.1 and 8.6.1.5.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A and Event 1F shall be used and "CFN-... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.6.4.2 Procedure | 1) The RF parameters are set up according to T1 in table 8.6.1.6.1.
2) The UE is switched on.
3) A call is set up with Cell 2 in AWGN conditions, according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The scrambling code is set to Cell1.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) The f... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.1.6.5 Test requirements | For the test to pass, the total number of successful tests shall be at least 90% of the cases with a confidence level of 95%. For the overall outcome of the test to be considered a pass, the counters for Event 1A and for Event 1F shall independently indicate a pass result.
Table 8.6.1.6.3: Test requirements for Cell sp... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2 FDD inter frequency measurements | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.1 Correct reporting of neighbours in AWGN propagation condition (Release 5 and earlier) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.1.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit the measurement report over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signallin... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.1.2 Minimum requirements | The UE shall be able to identify a new detectable cell belonging to the monitored set within
A cell shall be considered detectable when CPICH Ec/Io > -20 dB, SCH_Ec/Io > -17 dB for at least one channel tap and SCH_Ec/Ior is equally divided between primary synchronisation code and secondary synchronisation code. When L3... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.1.3 Test purpose | To verify that the UE meets the minimum requirements. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.1.4 Method of test | 8.6.2.1.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The initial test parameters are given in table 8.6.2.1.1
Table 8.6.2.1.1: Cell specific initial test parameters for Correct reporting
of neighbours in AWGN propagation condition
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.1.4.2 Procedure | 1) The parameters are set up according to table 8.6.2.1.2 and table 8.6.2.1.4.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The scrambling code is set to Cell2 and Cell3.
4) SS shall transmit a MEASUREMENT CONTROL message (inter frequency).
5... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.1.5 Test requirements | For the test to pass, the total number of successful tests shall be at least 90% of the cases with a confidence level of 95%. For the overall outcome of the test to be considered a pass, the counters for 2C events and for 1A events shall independently indicate a pass result.
Table 8.6.2.1.4: Test requirements for initi... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.2 Correct reporting of neighbours in fading propagation condition (Release 5 only) | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.2.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit the measurement report over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signallin... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.2.2 Minimum requirements | The requirements are the same as in sub clause 8.6.2.1.2.
The normative reference for these requirements is TS 25.133 [2] clauses 8.1.2.3 and A.8.2.2. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.2.3 Test purpose | To verify that the UE meets the minimum requirements. The test is performed in fading propagation conditions. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.2.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.6.2.2.4.1 and 8.6.2.2.4.2. In the measurement control information it is indicated to the UE that event-triggered reporting 2C shall be used. The test consists of two suc... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.2.4.2 Procedure | 1) The RF parameters are set up according to T1 in table 8.6.2.2.4.3.
2) The UE is switched on.
3) A call is set up in AWGN conditions, according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The scrambling code is set to Cell2.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) If compressed m... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.2.5 Test requirements | For the test to pass, the total number of successful tests shall be at least 90% of the cases with a confidence level of 95% According to annex F.6.2. The number of successful tests shall be on an event level, i.e. the SS shall check how many events are reported successfully out of the total number of events checked.
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.3 Correct reporting of neighbours in fading propagation condition using TGL1=14 | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.3.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit the measurement report over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signallin... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.3.2 Minimum requirements | The requirements are the same as in sub clause 8.6.2.1.2.
The normative reference for these requirements is TS 25.133 [2] clauses 8.1.2.3 and A.8.2.3. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.3.3 Test purpose | To verify that the UE meets the minimum requirements. The test is performed in fading propagation conditions using TGL1=14. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.3.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.6.2.3.4.1 and 8.6.2.3.4.2. In the measurement control information it is indicated to the UE that event-triggered reporting 2C shall be used. The test consists of two suc... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.3.4.2 Procedure | 1) The RF parameters are set up according to T1 in table 8.6.2.3.4.3.
2) The UE is switched on.
3) A call is set up in AWGN conditions, according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The scrambling code is set to Cell2.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) SS shall transm... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.2.3.5 Test requirements | For the test to pass, the total number of successful tests shall be at least 90% of the cases with a confidence level of 95% According to annex F.6.2. The number of successful tests shall be on an event level, i.e. the SS shall check how many events are reported successfully out of the total number of events checked.
... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3 TDD measurements | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1 Correct reporting of TDD neighbours in AWGN propagation condition | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This mea... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.2 Minimum requirement | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.2.1 3.84Mcps TDD option | When transmission gaps are scheduled for inter-frequency TDD measurements, the UE shall be able to identify a new detectable inter-frequency TDD cell belonging to the monitored set within
If the UE does not need compressed mode to perform inter-frequency TDD measurements, the UE shall be able to identify a new detecta... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.2.2 1.28Mcps TDD option | When transmission gaps are scheduled for inter-frequency TDD measurements, the UE shall be able to identify a new detectable inter-frequency TDD cell belonging to the monitored set within
If the UE does not need compressed mode to perform inter-frequency TDD measurements, the UE shall be able to identify a new detecta... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.3 Test purpose | To verify that the UE meets the minimum requirement. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.4.1 Initial conditions | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.4.1.1 3.84Mcps TDD option | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Table 8.6.3.1.1, 8.6.3.1.2 and 8.6.3.1.3. The test consists of 2 successive time periods, with a time duration T1 and T2. Two cells shall be present in the test, cell 1 being... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.4.1.2 1.28Mcps TDD option | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Table 8.6.3.1.1A, 8.6.3.1.2A and 8.6.3.1.3A. The test consists of 2 successive time periods, with a time duration T1 and T2. Two cells shall be present in the test, cell 1 being... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.4.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.3.2.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message.
6) UE shall transmit a... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.3.1.5 Test requirements | The UE shall send one Event 2C triggered measurement report for Cell 2 with a measurement reporting delay less than 9.2 s from the beginning of time period T2.
The UE shall not send event triggered measurement reports, as long as the reporting criteria are not fulfilled.
For the test to pass, the total number of succes... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4 GSM measurements | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1 Correct reporting of GSM neighbours in AWGN propagation condition | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit the measurement report over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signallin... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.2 Minimum requirements | Measurements on GSM cells can be requested with BSIC verified or BSIC non-verified.
1) In CELL_DCH state when a transmission gap pattern sequence is provided by the UTRAN the UE shall continuously measure GSM cells and search for new GSM cells given in the monitored set.
2) If the UE does not need compressed mode to pe... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.3 Test purpose | To verify that the UE meets the minimum requirements. |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.4 Method of test | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.4.1 Test 1 initial conditions | Test 1 with BSIC verification required case:
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.6.4.1, 8.6.4.2 and 8.6.4.3 below. In the measurement control information it is indicated to the UE that event-triggered repo... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.4.2 Test 1 Procedure | 1) The RF parameters are set up according to T0 in Table 8.6.4.2 and 8.6.4.7.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The RF parameters are set up according to T1 in Table 8.6.4.2 and 8.6.4.7.
4) If compressed mode is required, SS shall ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.4.3 Test 2 initial conditions | Test 2 without BSIC verification required case:
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.6.4.4, 8.6.4.5 and 8.6.4.6 below. In the measurement control information it is indicated to the UE that event-triggered r... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.4.4 Test 2 Procedure | 1) The RF parameters are set up according to T0 in Table 8.6.4.5 and 8.6.4.8.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] sub clause 7.3.2. The RF parameters are set up according to T1 in Table 8.6.4.5 and 8.6.4.8.
4) If compressed mode is required, SS shall ... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.5 Test requirements | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.5.1 TEST 1 With BSIC verification required | Table 8.6.4.7: Cell specific test parameters for Correct reporting of GSM neighbours in AWGN propagation condition (cell 2), test requirements
Parameter
Unit
Cell 2
T0
T1
T2
T3
Absolute RF Channel Number
BCCH ARFCN of cell A as defined in the initial conditions in clause 26.6.5.1 of TS 51.010-1 [25] for the GSM band un... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.4.1.5.2 TEST 2 Without BSIC verification required | Table 8.6.4.8: Cell specific test parameters for Correct reporting
of GSM neighbours in AWGN propagation condition (cell 2), test requirements
Parameter
Unit
Cell 2
T0
T1
T2
T3
Absolute RF Channel Number
BCCH ARFCN of cell A as defined in the initial conditions in clause 26.6.5.1 of TS 51.010-1 [25] for the GSM band un... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.5 Combined inter frequency and GSM measurements | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.5.1 Correct reporting of neighbours in AWGN propagation condition | |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.5.1.1 Definition and applicability | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit the measurement report over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signallin... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.5.1.2 Minimum requirement | When transmission gaps are scheduled for FDD inter frequency measurements the UE shall be able to identify a new detectable cell belonging to the monitored set within
ms
The UE physical layer shall when transmission gaps are scheduled for FDD inter frequency measurements also be capable of reporting measurements to hig... |
19eaceb417a28bf040422bcad9ef7619 | 34.121-1 | 8.6.5.1.3 Test purpose | To verify that the UE makes correct reporting of an event when doing combined inter frequency and GSM measurements. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.