hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.4.4 Method of test | Initial conditions
Cell_selection_and_reselection_quality_measure is CPICH_RSCP (FDD).
Each cell includes the other cells in the inter-frequency neighbour cell list in System Information Block Type 11.
For FDD only:
Step a-c:
Parameter
Unit
Cell 1
Cell 2
Cell 3
Test channel
1
2
3
LAC
0001
0002
0003
CPICH_Ec
dBm/3.84 MH... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.4.5 Test requirements | 1) In step c), after the UE has responded on Cell 1, it shall not respond on any other cell within 1 min.
2) In step e), there shall be no response from the UE on Cell 2 within 38 s after changing the parameters in step d), but the UE shall respond on Cell 2 within 49 s (see NOTE1).
3) In step g),There shall be no resp... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.5 HCS Cell reselection using reselection timing parameters for the R criterion | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.5.1 Definition | Test to verify that the UE performs the cell reselection correctly for hierarchical cell structures using TEMP_OFFSET and PENALTY_TIME applied to the R criterion. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.5.2 Conformance requirement | 1. When camped normally, the UE shall execute the cell reselection evaluation process on the following occasions/triggers:
1.1 UE internal triggers, so as to meet performance as specified in TS 25.133 for FDD mode and in TS 25.123 for TDD mode.
1.2 When information on the BCCH used for the cell reselection evaluation p... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.5.3 Test purpose | 1. Verify that TEMP_OFFSET is applied to the R criterion for a period of PENALTY_TIME if serving and neighbour cell have identical HCS priorities and that the timer is started when Qmeas,n > Qmeas,s + Qoffset1 s,n. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.5.4 Method of test | Initial conditions
Cell_selection_and_reselection_quality_measure is CPICH_RSCP (FDD).
For FDD only:
Step a-c:
Parameter
Unit
Cell 1
Cell 2
Cell 3
LAC
0001
0002
0003
CPICH_Ec
dBm/3.84 MHz
-60
-70
-75
HCS priority
1
1
1
Qhcss
dBm
-80
-80
-80
TEMP_OFFSET1n=1
dB
n/a
0
0
TEMP_OFFSET1n=2
dBm
inf
n/a
0
TEMP_OFFSET1n=3
dBm
in... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.6 Emergency calls | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.6.1 Definition | Test to verify that the UE shall be able to initiate emergency calls when no suitable cells of the selected PLMN are available, but at least one acceptable cell is available. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.6.2 Conformance requirement | 1. Acceptable cell:
An "acceptable cell" is a cell on which the UE may camp to obtain limited service (originate emergency calls). Such a cell shall fulfil the following requirements, which is the minimum set of requirements to initiate an emergency call in a UTRAN network: |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 1.1 The cell is not barred; | 1.2 The cell selection criteria are fulfilled.
2. A "suitable cell" is a cell on which the UE may camp on to obtain normal service. Such a cell shall fulfil all the following requirements.
2.1 The cell is part of the selected PLMN or, of a PLMN considered as equivalent by the UE according to the information provided by... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.6.3 Test purpose | 1. To verify that the UE shall be able to initiate emergency calls when no suitable cells of the selected PLMN are available, but at least one acceptable cell is available.
2. To verify that the UE selects a cell with S>0 and CellBarred = Not Barred (i.e. an "acceptable cell") when no suitable cells of the selected PLM... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.6.4 Method of test | Initial conditions
In step a-d, Cell 1 and 4 are neither suitable nor acceptable cells. Cell 7 is an acceptable cell but not suitable.
In step e-f, both Cell 1 and 7 are acceptable cells.
Prior to performing the actual test procedure PLMN3 is set as forbidden PLMN, so that the USIM will contain the following informatio... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.6.5 Test requirements | 1) In step d), the first access from the UE shall be on Cell 7.
2) In step g), the first access from the UE shall be on Cell 1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.7 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.8 Cell reselection: Equivalent PLMN | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.8.1 Definition | Test to verify that the UE performs the cell reselection correctly to a cell belonging to a PLMN Equivalent to the registered PLMN, if the serving cell of registered PLMN becomes barred or S<0. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.8.2 Conformance requirement | 1. When camped on a cell, the UE shall regularly search for a better cell according to the cell reselection criteria. If a better cell is found, that cell is selected. The change of cell may imply a change of RAT.
2. A "suitable cell" is a cell on which the UE may camp on to obtain normal service. Such a cell shall ful... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 2.1 The cell is part of the selected PLMN or of a PLMN considered as equivalent by the UE according to the information provided by the NAS | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 2.2 The cell is not barred | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 2.3 The cell is not part of the list of "forbidden LAs for roaming" | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 2.4 The cell selection criteria are fulfilled | 3. When camped normally, the UE shall execute the cell reselection evaluation process on the following occasions/triggers:
3.1 UE internal triggers, so as to meet performance as specified in TS 25.133 for FDD mode and in TS 25.123 for TDD mode. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 3.2 When information on the BCCH used for the cell reselection evaluation procedure has been modified | 4. Cell Reselection Criteria: |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 4.1 The UE shall perform ranking of all cells that fulfil the S criterion | 4.2 The cells shall be ranked according to the R criteria, deriving Qmeas,n and Qmeas,s and calculating the R values using CPICH RSCP, P-CCPCH RSCP and the averaged received signal level as specified in TS 25.133 and TS 25.123 for FDD, TDD and GSM cells, respectively.
The offset Qoffset1s,n is used for Qoffsets,n to ca... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.8.3 Test purpose | 1. To confirm that the UE treats the cell of the equivalent PLMN as a cell of the current PLMN.
2. To verify that the UE performs cell reselection on the following occasions:
2.1 Serving cell becomes barred.
2.2 S<0 for serving cell.
3. To verify conformance requirement 5.
NOTE: Reselection triggered by the cell becomi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.8.4 Method of test | Initial conditions
Treselection, Qhyst, Qoffset, TEMP_OFFSET and PENALTY_TIME are not used, so the cell-ranking criterion R equals CPICH_RSCP for FDD cells, and P-CCPCH RSCP for TDD cells.
The UE is Idle Updated on PLMN1 in cell 1.
Cell 1 indicates in System Information Block Type 11 that Cell 2 and Cell 4 are neighbou... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.8.5 Test requirements | 1) In step c), after the UE has responded on Cell 1, it shall not respond on any other cell within 1 min.
2) In step e), the UE shall respond on Cell 4.
3) In step g), the UE shall respond on Cell 2.
4) In step k), the UE shall respond on Cell 1. After the UE has responded on Cell 1, it shall not respond on any other c... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.9 Void | 6.1.2.9a Cell reselection using cell status and cell reservations – Type “A” USIM
6.1.2.9a.1 Definition
Test to verify that the UE correctly interprets cell status and cell reservations when performing cell reselection.
6.1.2.9a.2 Conformance requirement
1. When cell status is indicated as "not barred", "not reserved" ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.10 HCS inter-frequency cell reselection | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.10.1 Definition | Test to verify that the UE performs inter-frequency cell reselection correctly for hierarchical cell structures in FDD. This shall be done according to the received signal quality value Q and the quality level thresholds Sintrasearch, Sintersearch and SsearchHCS. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.10.2 Conformance requirement | 1. When camped normally, the UE shall execute the cell reselection evaluation process on the following occasions/triggers:
1.1 UE internal triggers, so as to meet performance as specified in TS 25.133 for FDD mode.
1.2 When information on the BCCH used for the cell reselection evaluation procedure has been modified.
2.... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.10.3 Test purpose | 1. Verify that in FDD the UE ignores inter-frequency cells for reselection when the inter-frequency cells have equal or lower HCS priority than the serving cell, and Sintraseach is not sent, and Sintersearch < Squal and SsearchHCS < Srxlev.
2. Verify that in FDD the UE reselect to an inter-frequency cells when Sintrase... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.10.4 Method of test | Initial conditions
SS shall indicate in System Information that HCS is in use.
Each cell shall include the other cells as neighbouring cells in System Information Block Type 11.
For FDD only:
Step a- d:
Parameter
Unit
Cell 1
Cell 2
Cell 3
Test Channel
1
1
2
LAC
0001
0002
0003
HCS priority
6
6
6
CPICH_Ec
dBm/3.84 MHz
-7... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.10.5 Test requirements | 1) In step c, the UE shall respond on cell 1.
2) In step d, the UE shall not respond on cell 2 or 3.
3) In step f), the UE shall respond on Cell 2.
4) In step h), the UE shall respond on Cell 3.
6.1.2.10a HCS inter-frequency cell reselection for inter-band operation
6.1.2.10a.1 Definition
This test case is identical to... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.11 Cell reselection in shared network environment | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.11.1 Definition | Test to verify that the UE performs cell reselection according to core specification 25.304 in a shared network environment (FDD). Correct handling of equivalent PLMNs is also verified. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.11.2 Conformance requirement | 1. suitable cell:
A "suitable cell" is a cell on which the UE may camp on to obtain normal service. Such a cell shall fulfil all the following requirements.
- The cell shall be part of either:
• the selected PLMN, or:
• the registered PLMN, or:
• a PLMN of the Equivalent PLMN list
according to the latest information pr... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 4.1 If HCS is not used in the serving cell the UE shall perform ranking of all cells that fulfil the criterion S, among: | - all measured cells (see subclause 5.2.6.1.1).
4.2 The cells shall be ranked according to the R criteria, deriving Qmeas,n and Qmeas,s and calculating the R values using CPICH RSCP, P-CCPCH RSCP and the averaged received signal level as specified in TS 25.133 and TS 25.123 for FDD, TDD and GSM cells, respectively.
The... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.11.3 Test purpose | 1. To verify that the UE is able to reselect to a higher ranked cell in shared network environment.
2. To verify that the UE treats a cell of an Equivalent PLMN as a cell of the Registered PLMN for cell reselection in shared network environment.
3. To verify that the UE respects the IE “MIB PLMN Identity” in Camped N... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.11.4 Method of test | Initial conditions
The UE is equipped with a USIM containing default values. The HPLMN (MCC+MNC) of the IMSI for the USIM is set to PLMN1.
Cell reselection parameters are set to default values, so the cell-ranking criterion R equals CPICH_RSCP.
Each cell indicates in System Information Block Type 11 that all other cell... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.11.5 Test requirements | 1) In step b), the UE shall respond on Cell 1.
2) In step d), the UE shall respond on Cell 2.
3) In step e), the UE shall respond on Cell 4.
4) In step g), the UE shall not respond on Cell 1, Cell 2 or Cell 5 within 1 min. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.12 Cell reselection based on absolute priority in SIB19 | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.12.1 Definition | Test to verify that the UE performs cell reselection based on absolute RAT priority defined in SIB 19. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.12.2 Conformance requirement | 5.2.6.1.2a Measurement rules for inter-frequency and inter-RAT cell reselection when
absolute priorities are used
…
If the UE has received absolute priority information for inter-frequency layers, the UE shall follow these rules:
- The UE shall perform measurements of inter-frequency layers with a priority higher than ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.12.3 Test purpose | 1. To verify that UE performs Higher Priority Cell Reselection based on absolute priority.
2. To verify that UE performs LowerPriority Cell Reselection based on absolute priority.
3. To verify that UE performs Equal Priority Cell Reselection based on absolute priority. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.12.4 Method of test | Initial conditions
System Simulator:
- 2 cells Cell 1 and Cell 4
- Cell 1 as the active cell with SS downlink transmission power settings according to “T0” in table 6.1.2.x below.
- SIB19 to be transmitted by both cells.
User Equipment:
- UE is in idle mode, registered on Cell 1 with power settings “T0”.
- Idle state (... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.2.12.5 Test requirements | 1) At step d), UE reselects to a higher priority Cell 4.
2) At step i), UE reselects to lower priority Cell 4.
3) At step m), UE reselects to equal priority Cell 4. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3 MBSFN Cluster selection and reselection | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.1 MBSFN only service recognition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.1.1 Definition | Test to verify that a UE supporting both transmit and receive functions correctly distinguishes an MBSFN only mode cluster from a unicast carrier cell and performs the procedures for either MBSFN cluster selection or UTRAN unicast carrier cell selection as appropriate. The unicast carrier cell may have some (but not a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.1.2 Conformance requirement | The MS shall perform registration on the PLMN if the MS is capable of services which require registration. In both automatic and manual modes, the concept of registration on a PLMN is used. An MS successfully registers on a PLMN if:
a) The MS has found a suitable cell of the PLMN to camp on; and
b) An LR request from t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.1.3 Test purpose | 1. To verify that the UE initiates PLMN registration following selection of a cell that does not indicate MBSFN only mode.
2. To verify that the UE performs PLMN selection procedures without registration in an MBSFN only mode cluster. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.1.4 Method of test | Initial condition
System Simulator:
MBSFN carrier: 1 cell, Cell 31 (PLMN1). In addition to broadcasting System Information, MCCH messages are transmitted by the SS using MBMS configuration C2 and Default1 MCCH scheduling (One ongoing session) according to subclause 11.1 or 11.2 of TS 34.108.
Unicast carrier: 1 cell, C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.1.5 Test requirements | 1) The UE sends a LOCATION UPDATING REQUEST message on the unicast carrier at step 2.
2) The UE sends a CLOSE UE TEST LOOP COMPLETE message on the unicast carrier at step 13. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.2 Suitable PLMN selection; MBSFN Frequency List present (unicast carrier) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.2.1 Definition | Test to verify that the UE performs selection of a suitable MBSFN cluster which is part of the registered PLMN or which is in the stored list of Equivalent PLMN, when the MBSFN Frequency List is present in the SIB11of the unicast carrier on which the UE has registered. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.2.2 Conformance requirement | suitable MBSFN cluster:
A cell is part of an MBSFN cluster if it is indicated in system information [4]. An MBSFN cluster provides exclusively MBMS services. A suitable MBSFN cluster shall fulfil all the following requirements:
- For FDD 3.84 Mcps TDD IMB and 3.84/7.68 Mcps TDD the MBSFN cluster shall be part of either... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.2.3 Test purpose | 1. To verify that when SIB11 of the unicast carrier that a UE is camped on contains IE MBSFN Frequency List, a UE supporting reception of MBMS service in MBSFN mode will select a suitable MBSFN cluster if services are listed in the variable MBMS_ACTIVATED_service.
2. To verify that the UE when selecting a suitable MB... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.2.4 Method of test | Initial condition
System Simulator:
MBSFN carrier(s): 6 cells. Cell 31 (PLMN1), Cell 32 (PLMN2), Cell 33 (PLMN1), Cell 34 (PLMN2), Cell 35 (PLMN3) and Cell 37 (PLMN3) are all switched off.
Unicast carrier: 1 cell, Cell 1 (PLMN1) default configuration.
NOTE: The IE MBSFN frequency list is included in SIB11 of Cell 1.
Us... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.2.5 Test requirements | 1) After step 17, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0.
2) After step 30, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.3 Suitable PLMN search; MBSFN Frequency List not present (unicast carrier) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.3.1 Definition | Test to verify that the UE performs a search and then selection of a suitable MBSFN cluster which is part of the registered PLMN or which is in the stored list of Equivalent PLMN, when the MBSFN Frequency List is not present in the SIB11of the unicast carrier on which the UE has registered. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.3.2 Conformance requirement | suitable MBSFN cluster:
A cell is part of an MBSFN cluster if it is indicated in system information [4]. An MBSFN cluster provides exclusively MBMS services. A suitable MBSFN cluster shall fulfil all the following requirements:
- For FDD, 3.84 Mcps TDD IMB and 3.84/7.68 Mcps TDD the MBSFN cluster shall be part of eithe... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.3.3 Test purpose | 1. To verify that when SIB11 of the unicast carrier that a UE is camped on does not contain IE MBSFN Frequency List, a UE supporting reception of MBMS service in MBSFN mode will search for a suitable MBSFN cluster if services are listed in the variable MBMS_ACTIVATED_services.
2. To verify that the UE when selecting ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.3.4 Method of test | Initial condition
System Simulator:
MBSFN carrier(s): 3 cells. Cell 31 (PLMN1), Cell 32 (PLMN2) and Cell 37 (PLMN3) are all switched off.
Unicast carrier: 1 cell, Cell 1 (PLMN1) default configuration.
NOTE: The IE MBSFN frequency list is not included in SIB11 of Cell 1.
User Equipment:
The UE is switched off.
The UE is... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.3.5 Test requirements | 1) After step 16, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0.
2) After step 28, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.4 Cell reservations and access restrictions; Normal access class only | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.4.1 Definition | Test to verify that a UE, not assigned to any of the special access classes (Access Classes 11 to 15), performs selection of a suitable MBSFN cluster in accordance with the cell reservations and access restrictions signalled over the air interface. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.4.2 Conformance requirement | For an MBSFN cluster (see [4]) when cell status is indicated "not reserved" for operator use and "not reserved" for future extension (Cell Reservation Extension),
- All UEs shall treat this MBSFN cluster as candidate during the MBSFN cluster selection and MBSFN cluster re-selection procedures.
For an MBSFN cluster (see... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.4.3 Test purpose | 1. To verify that a UE not assigned to any of the special access classes (Access Classes 11 to 15), supporting reception of MBMS service in MBSFN mode, will search for a suitable MBSFN cluster if services are listed in the variable MBMS_ACTIVATED_services.
2. To verify that a UE not assigned to any of the special acc... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.4.4 Method of test | Initial condition
System Simulator:
MBSFN carrier: 3 cells, Cell 31 (PLMN1), Cell 32 (PLMN1) and Cell 37 (PLMN1) which are all switched off.
Unicast carrier: 1 cell, Cell 1 (PLMN1) default configuration.
User Equipment:
The UE is switched off.
The UE is equipped with a Test-USIM containing default values. The HPLMN (M... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.4.5 Test requirements | 1) At step 13, CLOSE UE TEST LOOP COMPLETE shall not be received from the UE.
2) After step 25, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.5 Cell reservations and access restrictions; Operator access class | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.5.1 Definition | Test to verify that a UE, assigned to one of the Access Classes 11 or 15, performs selection of a suitable MBSFN cluster in accordance with the cell reservations and access restrictions signalled over the air interface. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.5.2 Conformance requirement | For an MBSFN cluster (see [4]) when cell status is indicated "not reserved" for operator use and "not reserved" for future extension (Cell Reservation Extension),
- All UEs shall treat this MBSFN cluster as candidate during the MBSFN cluster selection and MBSFN cluster re-selection procedures.
For an MBSFN cluster (see... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.5.3 Test purpose | 1. To verify that a UE assigned to one of the Access Classes 11 or 15 (in addition to one of the Access Classes 0 to 9), supporting reception of MBMS service in MBSFN mode, will search for a suitable MBSFN cluster if services are listed in the variable MBMS_ACTIVATED_services.
2. To verify that a UE assigned to one o... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.5.4 Method of test | Initial condition
System Simulator:
MBSFN carrier: 3 cells, Cell 31 (PLMN1), Cell 32 (PLMN1) and Cell 37 (PLMN1) all are switched off.
Unicast carrier: 1 cell, Cell 1 (PLMN1) default configuration.
User Equipment:
The UE is switched off.
The UE is equipped with a Test-USIM containing default values with the exception t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.5.5 Test requirements | 1) At step 12, CLOSE UE TEST LOOP COMPLETE shall not be received from the UE.
2) After step 26, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0.
3) After step 39, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.6 Cell reservations and access restrictions; Home country services access class | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.6.1 Definition | Test to verify that a UE, assigned to one of the Access Classes 12, 13 or 14, performs selection of a suitable MBSFN cluster in accordance with the cell reservations and access restrictions signalled over the air interface. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.6.2 Conformance requirement | For an MBSFN cluster (see [4]) when cell status is indicated "not reserved" for operator use and "not reserved" for future extension (Cell Reservation Extension),
- All UEs shall treat this MBSFN cluster as candidate during the MBSFN cluster selection and MBSFN cluster re-selection procedures.
For an MBSFN cluster (see... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.6.3 Test purpose | 1. To verify that a UE, assigned to just one of the Access Classes 12, 13 or 14 (in addition to one of the Access Classes 0 to 9), supporting reception of MBMS service in MBSFN mode, will search for a suitable MBSFN cluster if services are listed in the variable MBMS_ACTIVATED_services.
2. To verify that a UE, assign... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.6.4 Method of test | Refer to the "Method of test" in clause 6.1.3.4.4 with the following exception:
The UE is equipped with a Test-USIM containing default values with the exception that the field EFACC (Access Control Class) of the Test-USIM shall be set as per "Type D" in clause 8.3.2.15. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.6.5 Test requirements | Refer to the "Test requirements" in clause 6.1.3.4.5. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.7 Inter frequency neighbour reselection / Service activation | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.7.1 Definition | This test is applicable for UEs that support MBMS broadcast services in MBSFN mode and which support either both TDD transmit and receive functions or TDD MBSFN receive only function or 3.84 Mcps TDD IMB function. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.7.2 Conformance requirement | Upon detection of one MBSFN cluster all other frequencies on which MBMS service is provided in MBSFN mode for one of the PLMN assigned to the MBSFN cluster are indicate as specified in [4].
The UE chooses the frequency for the MBSFN cluster to be received based on the information on the services that are provided on t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.7.3 Test purpose | 1. To verify that on indication from upper layers that there has been a change to the activated service(s) the UE will perform a cluster reselection to an inter frequency neighbour cluster providing the required MBMS service .
2. To verify that the UE starts the reception of the activated MBMS service after reselection... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.7.4 Method of test | Initial condition
System Simulator:
- MBSFN carrier: 2 cells, Cell 31 (PLMN1) and Cell 33 (PLMN1). Cell 31 is powered off. In addition to broadcasting System Information, MCCH messages are transmitted by the SS on Cell 33 using MBMS configuration C1 and Default1 MCCH scheduling (No ongoing session) according to subcla... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.7.5 Test requirements | 1) After step 18, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.8 Inter frequency neighbour reselection / Activation of higher priority service | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.8.1 Definition | This test is applicable for UEs that support MBMS broadcast services in MBSFN mode and which support either both TDD transmit and receive functions or TDD MBSFN receive only function or 3.84 Mcps TDD IMB function. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.8.2 Conformance requirement | If the cell is operating in MBSFN mode according to subclause 8.1.1.6.3 the UE shall:
1> if for two or more services included in variable MBMS_ACTIVATED_SERVICES the IE "MBSFN cluster frequency" is available:
2> request from upper layers the priorities of the different MBMS services included in variable MBMS_ACTIVATED_... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.8.3 Test purpose | 1. To verify that the UE correctly handles the notification procedure after receiving the MBMS MODIFIED SERVICES INFORMATION message via MCCH indicating a change in available services.
2. To verify that the UE acts upon service priority indications from upper layers that require a change in MBSFN cluster frequency.
3. ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.8.4 Method of test | Initial condition
System Simulator:
- MBSFN carrier: 2 cells, Cell 31 (PLMN1) and Cell 33 (PLMN1). Cell 31 is powered off. In addition to broadcasting System Information, MCCH messages are transmitted by the SS on Cell 33 using MBMS configuration C1 and Default1 MCCH scheduling (No ongoing session) according to subcla... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.1.3.8.5 Test requirements | 1) After step 9, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0.
2) After step 20, the UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE message shall report a number > 0. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.2 Multi-mode environment (2G/3G case) | For Inter-RAT idle mode test cases cells belonging to different RAT shall use different LAC and RAC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.2.1 PLMN and RAT selection | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.2.1.1 Selection of the correct PLMN and associated RAT | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 6.2.1.1.1 Definition | Test to verify that the UE selects the correct combination of PLMN and associated access technology according to the fields on the USIM. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.