hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.3.2.5 Test requirements | 1. After step 8 the UE shall loopback data on RB6 using the transport format that carries the maximum amount of data (2 PDUs per TTI)
2. After step 10 the UE shall transmit a MEASUREMENT REPORT message within 500 ms.
3. After step 10 and during the reception of the MEASUREMENT REPORT message, data shall also be receive... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.4.1 Control of CPCH transmissions for FDD | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.4.1.1 Definition and applicability | All UEs which support CPCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.4.1.2 Conformance requirement | 1. If counter M is not less than N_access_fails, the UE shall execute an access failure error procedure and the CPCH access procedure ends.
2. If the sum of the Frame Count Transmitted counter plus the number of frames in the next TTI is larger than NF_max, the UE shall exit the CPCH transmission procedure.
3. If the C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.4.1.3 Test purpose | To verify that the MAC entity control CPCH transmission correctly. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.4.1.4 Method of test | Initial conditions
System Simulator:
- 1 cell, default parameters, Ciphering Off.
User Equipment:
- The UE shall operate under normal test conditions, Ciphering Off.
- The Test-USIM shall be inserted.
The UE is in Connected mode and a connection is established as described in the TS 34.123-1, clause 7.3 PDCP testing, c... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.4.1.5 Test requirements | The SS can't receives data blocks from UE when N_access_fails or NF_max set as 0.
The SS can't receives data blocks from UE when NF_max set as 0.
The SS can't receives data blocks from UE when CSICH info indicates channels not available.
The SS can't receives data blocks from UE when CPCH Persistency level set to 8.
Th... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5 HS-DSCH MAC-hs | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.1 MAC-hs reordering and stall avoidance | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.1.1 Definition and applicability | All UEs which support HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.1.2 Conformance requirement | When a MAC-hs PDU with TSN = SN is received:
- If SN is within the receiver window:
- if SN < next_expected_TSN, or this MAC-hs PDU has previously been received:
- the MAC-hs PDU shall be discarded.
- else:
- the MAC-hs PDU is placed in the reordering buffer at the place indicated by the TSN.
- If SN is outside the re... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.1.3 Test purpose | 1. To confirm that the UE performs MAC-hs reordering and delivers RLC PDUs in order to RLC.
2. To confirm that the UE performs stall avoidance in case of missing MAC-hs PDUs based on a) window based stall avoidance and b) timer based stall avoidance. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.1.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration “Interactive or background / UL:64 DL: [max bit rate depending on UE category] / PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH” as specified in TS 34.108, clause 6.10.2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.1.5 Test requirements | 1. After step 1, the RLC PDU with SN = 0 shall be looped back
2. After step 3, the RLC PDU with SN = 1 shall be looped back
3. After step 5 and 6 , no data shall be looped back
4. After step 7, no data shall be looped back and no RLC status report shall be received
5. After step 9, the RLC PDUs with SN = 2,3 shall be l... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.2 MAC-hs priority queue handling | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.2.1 Definition and applicability | All UEs which support HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.2.2 Conformance requirement | Reordering Queue distribution:
The reordering queue distribution function routes the MAC-hs PDUs to the correct reordering buffer based on the Queue ID.
[...]
The HARQ process processes the Queue ID in the received MAC-hs PDUs. The UE shall:
- arrange the received MAC-hs PDUs in queues based on the Queue ID.
[...]
Refe... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.2.3 Test purpose | 1. To confirm that the UE handles several priority queues, where different radio bearers are mapped to different queues. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.2.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration “5 x Interactive or background / UL: 8 kbps DL: [max bit rate depending on UE category] / UM PS RAB” as specified in TS 34.108, clause 6.11.4a.1 with the logical ch... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.2.5 Test requirements | 1. In step 2, for each iteration, the RLC PDU with SN=0 shall be looped back with the logical channel ID as specified by the table below:
Iteration
Logical Channel ID
1
7
2
8
3
9
4
10
5
13
NOTE: Logical Channel ID 13 is the Uplink Logical Channel Identity of RB9. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.3 MAC-hs PDU header handling | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.3.1 Definition and applicability | All UEs which support HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.3.2 Conformance requirement | MAC PDU (HS-DSCH):
[...]
The following fields are included in the MAC header for HS-DSCH:
- Version Flag (VF):
The VF field is a one bit flag providing extension capabilities of the MAC-hs PDU format. The VF field shall be set to zero and the value one is reserved in this version of the protocol.
- Queue identifier (Qu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.3.3 Test purpose | 1. To confirm that the UE discards PDUs with reserved values of the fields in the MAC header
2. To confirm that the UE discards PDUs with values in the MAC header that are inconsistent with the RRC configuration.
3. To confirm that the UE correctly reads the MAC header and disassembles the MAC-hs PDU into MAC-d PDUs an... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.3.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration “Interactive or background / UL:64 DL: [max bit rate depending on UE category] / PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH” as specified in TS 34.108, clause 6.10.2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.3.5 Test requirements | 1. After step 1, no data shall be looped back to the SS
2. After step 3, no data shall be looped back to the SS
3. After step 5, the RLC PDUs with SN =0,1, ...,7 shall be looped back to the SS |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.4 MAC-hs retransmissions | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.4.1 Definition and applicability | All UEs which support HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.4.2 Conformance requirement | [...]
The UE shall:
- if the New Data Indicator has been incremented compared to the value in the previous received transmission in this HARQ process or this is the first received transmission in the HARQ process:
- replace the data currently in the soft buffer for this HARQ process with the received data.
- if the Tra... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.4.3 Test purpose | 1. To confirm that the UE correctly transmit positive and negative acknowledgements when receiving MAC-hs PDUs |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.4.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration “Interactive or background / UL:64 DL: [max bit rate depending on UE category] / PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH” as specified in TS 34.108, clause 6.10.2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.4.5 Test requirements | 1. After step 1, a MAC-hs negative acknowledgement shall be received for the correct HARQ process
2. After step 3, a MAC-hs positive acknowledgement shall be received for the correct HARQ process |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.5 MAC-hs reset | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.5.1 Definition and applicability | All UEs which support HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.5.2 Conformance requirement | Rel-5 and Rel-6:
If a reset of the MAC-hs entity is requested by upper layers, the UE shall:
- flush soft buffer for all configured HARQ processes;
- stop all active re-ordering release timer (T1) and set all timer T1 to their initial value;
- start TSN with value 0 for the next transmission on every configured HARQ pr... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.5.3 Test purpose | 1. To confirm that the UE flushes the reordering buffer and delivers all MAC-d PDUs in the buffer to higher layers upon reset.
2. To confirm that the UE initializes the TSN and next_expected_TSN to their initial values. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.5.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off
User Equipment:
The SS establishes the reference radio bearer configuration “Interactive or background / UL:64 DL: [max bit rate depending on UE category] / PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH” as specified in TS 34.108, clause 6.10.2.... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.5.5 Test requirements | 1. After step 1, the RLC PDU with SN = 0 shall be looped back
2. After step 5, the RLC PDUs with SN = 1,2 shall be looped back
3. After step 9, the RLC PDU with SN=3 shall be looped back |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.6 MAC-hs transport block size selection | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.6.1 Definition and applicability | All UEs which support HS-PDSCH and FDD. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.6.2 Conformance requirement | For HS-DSCH the transport block size is derived from the value signalled on the HS-SCCH. The mapping between the TFRI value and the transport block size for each mode is specified below:
For all transmissions of a transport block, the transport block size is derived from the TFRI value as specified below, except only i... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.6.3 Test purpose | To verify that the UE selects the correct transport block size based on the TFRI value signalled on the HS-SCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.6.4 Method of test | NOTE: The reference to UE Categories refers to the UE capability as signalled in the Rel-5 IE “HS-DSCH physical layer category” (1 to 12). All UEs supporting HS-DSCH should signal a category between 1 and 12 for this IE even if the UE physical capability category is above 12. This IE corresponds to the HS-DSCH category... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.6.5 Test requirements | For each TFRC the UE shall return a UL RLC SDUs with the same content as the first 312 bits of the test data sent by the SS in downlink.
7.1.5.6a MAC-hs transport block size selection (1.28 Mcps TDD)
7.1.5.6a.1 Definition and applicability
All 1.28 Mcps TDD UEs which support HS-PDSCH.
7.1.5.6a.2 Conformance requirement... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.7 MAC-hs transport block size selection (3.84 Mcps TDD) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.7.1 Definition and applicability | All 3.84 Mcps TDD UEs which support HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.7.2 Conformance requirement | For HS-DSCH the transport block size is derived from the value signalled on the HS-SCCH. The mapping between the TFRI value and the transport block size for each mode is specified below:
Let k be the signalled TFRI value, then the corresponding HS-DSCH transport block size Lk is given by:
If k=1..510
If k = 511
Lk = 10... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.7.3 Test purpose | To verify that the UE selects the correct transport block size based on the TFRI value signalled on the HS-SCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.7.4 Method of test | Definition of test variables:
Nslots
Number of HS-DSCH slots (2, 4, 6 or 12 dependent on UE category)
Ncodes
Number of HS-DSCH codes per timeslot, 1 to 16
k
TFRI signalled on the HS-SCCH value (see Table 7.1.5.7.2)
TBsize
Transport Block size (see Table 7.1.5.7.2)
NPDUs
Number of MAC-d PDUs
MAC-hs_header_size
MAC-hs he... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.7.5 Test requirements | For each TFRC the UE shall return a UL RLC SDUs with the same content as the first 312 bits of the test data sent by the SS in downlink. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.8 MAC-hs transport block size selection (7.68 Mcps TDD) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.8.1 Definition and applicability | All 7.68 Mcps TDD UEs which support HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.8.2 Conformance requirement | For HS-DSCH the transport block size is derived from the value signalled on the HS-SCCH. The mapping between the TFRI value and the transport block size for each mode is specified below:
Let k be the signalled TFRI value, then the corresponding HS-DSCH transport block size Lk is given by:
If k=1..510
If k = 511
Lk = 20... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.8.3 Test purpose | To verify that the UE selects the correct transport block size based on the TFRI value signalled on the HS-SCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.8.4 Method of test | Definition of test variables:
Nslots
Number of HS-DSCH slots (1, 2, 3, 4, 5, 8 or 12 dependent on UE category)
Ncodes
Number of HS-DSCH codes per timeslot, 1 to 16
k
TFRI signalled on the HS-SCCH value (see Table 7.1.5.8.2)
TBsize
Transport Block size (see Table 7.1.5.8.2)
NPDUs
Number of MAC-d PDUs
MAC-hs_header_size
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.8.5 Test requirements | For each TFRC the UE shall return a UL RLC SDUs with the same content as the first 312 bits of the test data sent by the SS in downlink. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.9 MAC-hs data transmission with enhanced TS0 (1.28 Mcps TDD) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.9.1 Definition and applicability | All UEs which support HS-PDSCH and 1.28Mcps TDD and enhanced TS0. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.9.2 Conformance requirement | For 1.28 Mcps, the timeslots to be used for HS-PDSCH resources are signalled by the bits xts,1, xts,2, …, xts,5, where bit xts,n carries the information for timeslot n+1. Timeslot 1 cannot be used for HS-DSCH resources. If the signalling bit is set (i.e. equal to 1), then the corresponding timeslot shall be used for HS... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.9.3 Test purpose | To verify that the UE can receive the data transmitted in TS0 with MAC-hs. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.9.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off cell1 configures 3 carrier frequency, one is primary frequency, other are secondary frequencies. The frequency relation show as below:
Parameter
Cell 1
UTRA RF Channel Number1
Ch. 1
UTRA RF Channel Number2
Ch. 2
UTRA RF Channel Number3
Ch.3
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.5.9.5 Test requirements | In step6 the UE shall return a UL RLC SDUs with the same content as the first 312 bits of the test data sent by the SS in downlink.
7.1.5a HS-DSCH MAC-ehs
7.1.5a.1 MAC-ehs multiplexing / multiple logical channels on same queue
7.1.5a.1.1 Definition and applicability
All UEs which support MAC-ehs.
7.1.5a.1.2 Conformance... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 2 To test UE is able to combine MAC-ehs SDU segments from consecutive MAC-ehs PDU’s | 3. To test UE discards stored MAC-ehs SDU segment, if it cannot be combined.
7.1.5a.3.4 Method of test
Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration 1 x Interactive or background / UL: 8 kbps DL: [max bit rate ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6 E-DCH MAC-es/e | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1 MAC-es/e multiplexing | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.1 MAC-es/e multiplexing without RRC restrictions | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.1.1 Definition and applicability | All UEs which support E-DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.1.2 Conformance requirement | From 25.321 clause 9.1.5:
In the case of E-DCH there are two MAC sublayers, MAC-e and MAC-es. MAC-es sits on top of MAC-e and receives PDUs directly from MAC-d. MAC-es SDUs (i.e. MAC-d PDUs) of the same size, coming from a particular logical channel can be multiplexed together into a single MAC-es payload. To this payl... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.1.3 Test purpose | The purpose of this test case is to verify that the UE multiplexes data from different logical channels in the same TTI when no restriction on the multiplexing is configured by RRC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.1.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration specified in TS 34.108 clause 6.11.4d(FDD) /6.11.5.4.7.7(1.28Mcps TDD) using condition A15(FDD) /A14(1.28Mcps TDD) as specified in clause 9.1 of TS 34.108. The logi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.1.5 Test requirements | 1. After step 2 the SS shall receive an SI indicating that data is available on LCH 1 and LCH 2 but no RLC PDUs shall be received
2. In step 6, the SS shall receive 1 RLC PDU on LCH 1 and one RLC PDU on LCH 2 in the same TTI |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.2 MAC-es/e multiplexing with RRC restrictions | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.2.1 Definition and applicability | All UEs which support E-DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.2.2 Conformance requirement | From 25.321 clause 9.1.5:
In the case of E-DCH there are two MAC sublayers, MAC-e and MAC-es. MAC-es sits on top of MAC-e and receives PDUs directly from MAC-d. MAC-es SDUs (i.e. MAC-d PDUs) of the same size, coming from a particular logical channel can be multiplexed together into a single MAC-es payload. To this payl... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.2.3 Test purpose | The purpose of this test case is to verify that the UE does not multiplex data from different logical channels in the same TTI when the multiplexing has been restricted by RRC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.2.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration specified in TS 34.108 clause 6.11.4d(FDD) /6.11.5.4.7.7(1.28Mcps TDD) using condition A15(FDD) /A14(1.28Mcps TDD) as specified in clause 9.1 of TS 34.108.The logic... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.2.5 Test requirements | 1. After step 2 the SS shall receive an SI indicating that data is available on LCH 1 and LCH 2 but no RLC PDUs shall be received
2. In step 6, the SS shall receive 1 RLC PDU on LCH 1 but no data from LCH 2
3. In step 7, the SS shall receive 1 RLC PDU on LCH 2 but no data from LCH 1 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.3 Correct settings of MAC-es/e header fields | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.3.1 Definition and applicability | All UEs which support E-DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.3.2 Conformance requirement | Extract from 25.321:
[…]
- Transmission Sequence Number (TSN):
The TSN field provides the transmission sequence number for the MAC-es PDU. This information is used for reordering purposes to support in-sequence delivery to higher layers. The length of the TSN field is 6 bits.
[…]
- For FDD: Data description indicator (... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.3.3 Test purpose | The purpose of this test case is to verify that the UE sets the MAC-es/e header fields in a correct way. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.3.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration specified in TS 34.108 clause 6.11.4d(FDD) /6.11.5.4.7.7(1.28Mcps TDD) using condition A15(FDD) /A14(1.28Mcps TDD) as specified in clause 9.1 of TS 34.108. The logi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.1.3.5 Test requirements | 1. After step 4, the SS shall receive 1 MAC-es PDU shall be received where:
- The TSN is set to 0, DDI is set to 6 and N is set to 4
2. After step 10, the SS shall receive 2 MAC-es PDUs shall be received where:
- For MAC-es PDU 1: The TSN is set to 0, DDI is set to 5 and N is set to 2
- For MAC-es PDU 2: The TSN is set... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2 MAC-es/e – Scheduling | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.1 Correct settings of MAC-es/e scheduling information | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.1.1 Definition and applicability | All UEs which support E-DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.1.2 Conformance requirement | Extract From 25.321 clause 9.2.5.3.2:
This information includes the following fields:
The Scheduling Information shall not be transmitted if the Total E-DCH Buffer Status is zero, even if it was triggered by one of the configured triggering mechanisms.
[…]
If data with higher priority than the data already in the trans... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.1.3 Test purpose | The purpose of this test case is to verify that the UE sends the E-DCH scheduling information with correct content and with correct triggers. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.1.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration specified in TS 34.108 clause 6.11.4d(FDD) /6.11.5.4.7.7(1.28Mcps TDD) using condition A15(FDD) /A14(1.28Mcps TDD) as specified in clause 9.1 of TS 34.108. The logi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.1.5 Test requirements | 1. In step 1 the SS shall not receive any SI since the UE buffer is empty
2. In step 3 the SS shall receive an SI (content ignored)
3. In step 4 the SS shall receive an SI indicating
- Total E-DCH Buffer Status (TEBS) Index = 6 (32 < TEBS ≤ 42).
- Highest priority Logical channel ID (HLID) = LCH 2.
- Highest Priority L... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.2 Happy bit setting | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.2.1 Definition and applicability | All UEs which support E-DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.2.2 Conformance requirement | The happy bit is a single bit field that is passed from MAC to the physical layer for inclusion on the E-DPCCH. This field takes two values, “Not Happy” and “Happy” indicating respectively whether the UE could use more resources or not. The setting of the Happy Bit is defined in subclause [TS 25.321] 11.8.1.5.
[…]
The ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.2.3 Test purpose | The purpose of this test case is to verify that the UE sets the happy bit correctly. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.2.4 Method of test | Initial conditions
System Simulator:
1 cell, default parameters, Ciphering Off.
User Equipment:
The SS establishes the reference radio bearer configuration specified in TS 34.108 clause 6.11.4c using condition A12 as specified in clause 9.1 of TS 34.108.
The following parameters are specific for this test case:
Paramet... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.2.5 Test requirements | 1. In step 3 the SS shall receive data and the happy bit shall be set to happy in the first TTI containing data
2. In step 7 the SS shall receive data and the happy bit shall be set to unhappy in the first TTI containing data
3. In step 10 the SS shall receive data and the happy bit shall be set to happy in the first T... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.3 MAC-es/e non-scheduled transmissions | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.3.1 Definition and applicability | All UEs which support E-DCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.3.2 Conformance requirement | Extract From 25.321 clause 11.8.1.4:
[…]
RRC can allocate non-scheduled transmission grants to individual MAC-d flows in order to reduce the transmission delays. When a 2ms TTI is configured each non-scheduled grant is applicable to the specific set of HARQ processes indicated by RRC. The applicability of scheduled gra... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 7.1.6.2.3.3 Test purpose | To verify that the UE when RRC is configured for non-scheduled transmissions sends data without scheduling grant. To verify that no SI is sent for non-scheduled transmissions. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.