hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.7.3 Test purpose | To confirm that when the UE receives an RRC CONNECTION RELEASE message, the UE releases signalling radio bearer and its radio resources and goes back to the idle.
To confirm that the UE enters into idle mode with by performing cell-selection and selecting other cell than the UE selecting cell in connected mode. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.7.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 is active and cell 6 is inactive
UE: "Registered idle mode on CS" (state 2) or "Registered idle mode on PS" (state 3) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain supported by the UE If the UE supports both CS and PS domains, the init... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.7.5 Test requirement | After step 3 the UE shall transmit RRC CONNECTION RELEASE COMPLETE messages using AM on DCCH.
After step 9 the UE shall be in idle mode of cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.8 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.9 RRC Connection Release in CELL_DCH state (Network Authentication Failure): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.9.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.9.2 Conformance requirement | 1. TS 25.331
If the upper layers request the release of the RRC connection, the UE shall:
1> release all its radio resources;
1> enter idle mode;
1> perform other actions when entering idle mode from connected mode as specified in subclause 8.5.2;
1> if the UE was in CELL_DCH state prior to entering idle mode:
2> consi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.9.3 Test purpose | To confirm that when the upper layers request the release of the RRC connection, the UE releases signalling radio bearer and its radio resources and goes back to idle mode.
To confirm that the UE enters idle mode, bars the cell for a period Tbarred and hence performs cell-selection to another (non-barred) cell. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.9.4 Method of test | Initial Condition
System Simulator: 3 cells – Cell 1, 2 and 3 are active.
UE: "CS-DCCH+DTCH_DCH" (state 6-9) or " PS-DCCH+DTCH_DCH " (state 6-10) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain supported by the UE.
Test Procedure
Table 8.1.3.9 illustrates the downlink power to be applied f... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.3.9.5 Test requirement | At step 1 the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH using AM RLC.
After step 2 the UE shall transmit an ACTIVE SET UPDATE COMPLETE message on the uplink DCCH.
After step 4 the UE shall transmit an UPLINK DIRECT TRANSFER messages using AM on DCCH.
After step 7, the UE shall transmit RRC CONNE... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.4 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5 UE capability | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.1 UE Capability in CELL_DCH state: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.1.2 Conformance requirement | The UE shall initiate the UE capability update procedure in the following situations:
1> the UE receives a UE CAPABILITY ENQUIRY message from the UTRAN;
…
If the UE CAPABILITY INFORMATION message is sent in response to a UE CAPABILITY ENQUIRY message, the UE shall:
1> include the IE "RRC transaction identifier"; and
1>... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.1.3 Test purpose | 1. To confirm that the UE transmits a UE CAPABILITY INFORMATION message after it receives a UE CAPABILITY ENQUIRY message from the SS.
2. To confirm that the UE indicates an invalid message reception when invalid UE CAPABILITY ENQUIRY and UE CAPABILITY INFORMATION CONFIRM messages are received. The UE shall transmit RR... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.1.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_DCH state (state 6-9 or state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is brought to the CELL_DCH state after a successful outgoing call attempt. The SS transmits a UE CAPABILITY ENQUIRY m... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.1.5 Test requirement | After step 2, the UE shall transmit a RRC STATUS message on the uplink DCCH, reporting the error with protocol error cause set to "Message extension not comprehended" correct transaction identifier.
After step 4 and 7 the UE shall transmit a UE CAPABILITY INFORMATION message on the uplink DCCH to respond to the UE CAPA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.2 UE Capability in CELL_DCH state: Success after T304 timeout | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.2.2 Conformance requirement | The UE shall initiate the UE capability update procedure in the following situations:
1> the UE receives a UE CAPABILITY ENQUIRY message from the UTRAN on the DCCH using UM or AM RLC;
1> while in connected mode the UE capabilities change compared to those stored in the variable UE_CAPABILITY_TRANSFERRED.
If the UE CAPA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.2.3 Test purpose | To confirm that the UE re-transmits a UE CAPABILITY INFORMATION message until V304 is greater than N304, after the expiry of timer T304 when the UE cannot receive a UE CAPABILITY INFORMATION CONFIRM message in response to a UE CAPABILITY INFORMATION message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.2.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_DCH state (state 6-9 or state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is brought to CELL_DCH state. When the SS transmits a UE CAPABILITY ENQUIRY message which includes the "Capability up... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.2.5 Test requirement | After step 3 the UE shall re-transmits a UE CAPABILITY INFORMATION message on the uplink DCCH, after each expiry of timer T304. The UE CAPABILITY INFORMATION message shall contain IE "UE radio access capability" indicating the settings found in PIC/PIXIT statements. After (N304) re-transmissions, the UE shall receive a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.3 UE Capability in CELL_DCH state: Failure (After N304 re-transmissions) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.3.2 Conformance requirement | The UE shall initiate the UE capability update procedure in the following situations:
1> the UE receives a UE CAPABILITY ENQUIRY message from the UTRAN on the DCCH using UM or AM RLC;
1> while in connected mode the UE capabilities change compared to those stored in the variable UE_CAPABILITY_TRANSFERRED.
If the UE CAPA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.3.3 Test purpose | To confirm that the UE stops retrying to transmit a UE CAPABILITY INFORMATION message if V304 is greater than N304. It then initiates cell update procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.3.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_DCH state (state 6-9 or state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is brought to CELL_DCH state. When the SS transmits a UE CAPABILITY ENQUIRY message which includes the "Capability up... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.3.5 Test requirement | After step 2, the UE shall transmit a UE CAPABILITY INFORMATION message on the uplink DCCH. The UE shall re-transmit this message for N304 times.
After step 4, the UE shall initiate the cell update procedure.
After step 6, UE shall respond with a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message after it has configured... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.4 UE Capability in CELL_FACH state: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.4.2 Conformance requirement | The UE shall initiate the UE capability update procedure in the following situations:
1> the UE receives a UE CAPABILITY ENQUIRY message from the UTRAN;
…
If the UE CAPABILITY INFORMATION message is sent in response to a UE CAPABILITY ENQUIRY message, the UE shall:
1> include the IE "RRC transaction identifier"; and
1>... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.4.3 Test purpose | 1. To confirm that the UE transmits a UE CAPABILITY INFORMATION message after it receives a UE CAPABILITY ENQUIRY message from the SS.
2. To confirm that the UE indicates an invalid message reception when invalid UE CAPABILITY ENQUIRY and UE CAPABILITY INFORMATION CONFIRM messages are received. The UE shall transmit RR... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.4.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_FACH state (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is brought to the CELL_FACH state after a successful outgoing call attempt. The SS transmits a UE CAPABILITY ENQUIRY message containing an unexpected critical message extension. Af... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.4.5 Test requirement | After step 2, the UE shall transmit a RRC STATUS message on the uplink DCCH, reporting the error with protocol error cause set to "Message extension not comprehended" correct transaction identifier.
After step 4 and 7 the UE shall transmit a UE CAPABILITY INFORMATION message on the uplink DCCH to respond to the downlin... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.5 UE Capability in CELL_FACH state: Success after T304 timeout | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.5.2 Conformance requirement | The UE shall initiate the UE capability update procedure in the following situations:
1> the UE receives a UE CAPABILITY ENQUIRY message from the UTRAN on the DCCH using UM or AM RLC;
1> while in connected mode the UE capabilities change compared to those stored in the variable UE_CAPABILITY_TRANSFERRED.
If the UE CAPA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.5.3 Test purpose | To confirm that the UE re-transmits a UE CAPABILITY INFORMATION message until V304 is greater than N304, after the expiry of timer T304 when it fails to receive a downlink UE CAPABILITY INFORMATION CONFIRM message in response to the uplink UE CAPABILITY INFORMATION message sent. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.5.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_FACH state (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is brought to CELL_FACH state. When the SS transmits a UE CAPABILITY ENQUIRY message which includes the IE "Capability update requirement", the UE shall reply with a UE CAPABILITY ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.5.5 Test requirement | After step 3 the UE shall re-transmit a UE CAPABILITY INFORMATION message on the uplink DCCH, after each expiry of timer T304. The UE CAPABILITY INFORMATION message shall contain IE "UE radio access capability" with the value matching those stated in the ICS/IXIT statements. After (N304) re-transmissions, the UE shall ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.6.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.6.2 Conformance requirement | The UE shall initiate the UE capability update procedure in the following situations:
1> the UE receives a UE CAPABILITY ENQUIRY message from the UTRAN;
…
If the UE CAPABILITY INFORMATION message is sent in response to a UE CAPABILITY ENQUIRY message, the UE shall:
1> include the IE "RRC transaction identifier"; and
1>... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.6.3 Test purpose | To confirm that a multi-RAT UE responds with a UE CAPABILITY INFORMATION message after it receives a UE CAPABILITY ENQUIRY message from the UTRAN and it includes the inter-RAT-specific UE radio access capability information element.
8.1.5.6.4 Method of test
Initial Condition
System Simulator: 1 cell - Cell 1 is UTRAN.... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.6.5 Test requirement | After step 2 the UE shall transmit a UE CAPABILITY INFORMATION message on the uplink DCCH to respond to the UE CAPABILITY ENQUIRY message as per the specific message contents. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.7 UE Capability Information / Audit of UE Capabilities | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.7.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.7.2 Conformance requirement | The UE shall, in the transmitted RRC CONNECTION REQUEST message:
…
1> if the UE only supports HS-DSCH but not E-DCH:
2> include the IE "UE capability indication" and set it to the "HS-DSCH" value.
1> if the UE supports HS-DSCH and E-DCH:
2> include the IE "UE capability indication" and set it to the "HS-DSCH+E-DCH" val... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.7.3 Test purpose | To check that the entire UE capabilities the UE reported in RRC CONNECTION REQUEST, RRC CONNECTION SETUP COMPLETE and UE CAPABILITY INFORMATION messages are compatible with the ICS statements in 3GPP TS 34.123-2[3], TS 36.523-2[46], TS 51.010-2[45] and with IXIT statements in TS 34.123-3[12] and TS 36.523-3[47]. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.7.4 Method of test | Initial Condition
System Simulator: 1 cell - Cell 1 is UTRAN.
UE: Idle state (state 2 or state 3 or state 7) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE transmits an RRC CONNECTION REQUEST message to the SS on the uplink CCCH by attempting to make a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.5.7.5 Test requirement | At step 5 the UE shall transmit a UE CAPABILITY INFORMATION message on the uplink DCCH to respond to the UE CAPABILITY ENQUIRY message as per the specific message contents.
All ICS and IXIT parameters concerned shall be correctly set to those values which are reported by the UE so that the whole ICS / IXIT values can b... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6 Direct Transfer | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.1 Direct Transfer in CELL DCH state (invalid message reception and no signalling connection exists) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.1.2 Conformance requirement | If the UE receives a DOWNLINK DIRECT TRANSFER message, and the signalling connection identified with the IE "CN domain identity" does not exist according to the variable ESTABLISHED_SIGNALLING_CONNECTIONS, the UE shall:
1> ignore the content of the DOWNLINK DIRECT TRANSFER message;
1> transmit an RRC STATUS message on ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.1.3 Test purpose | To confirm that the UE transmits an RRC STATUS message on the DCCH using AM RLC if it receives a DOWNLINK DIRECT TRANSFER message with a non comprehended critical extension. To confirm that the UE transmits an RRC STATUS message on the DCCH using AM RLC if it receives a DOWNLINK DIRECT TRANSFER message which includes a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.1.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_DCH (state 6-9 or state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in the CELL_DCH state. The SS transmits an invalid DOWNLINK DIRECT TRANSFER message to the UE. The UE shall transmit an ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.1.5 Test requirement | After step 1 the UE shall transmit an RRC STATUS message on the DCCH using AM RLC setting "Message extension not comprehended" in IE "Protocol error cause" and "DOWNLINK DIRECT TRANSFER" in IE "Received message type".
After step 3 the UE shall transmit a n RRC STATUS message on the DCCH using AM RLC setting "Message no... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.2 Direct Transfer in CELL FACH state (invalid message reception and no signalling connection exists) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.2.2 Conformance requirement | If the UE receives a DOWNLINK DIRECT TRANSFER message, and the signalling connection identified with the IE "CN domain identity" does not exist according to the variable ESTABLISHED_SIGNALLING_CONNECTIONS, the UE shall:
1> ignore the content of the DOWNLINK DIRECT TRANSFER message;
1> transmit an RRC STATUS message on ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.2.3 Test purpose | To confirm that the UE transmits an RRC STATUS message on the DCCH using AM RLC if it receives a DOWNLINK DIRECT TRANSFER message which does not include any IEs except IE "Message Type". To confirm that the UE transmits an RRC STATUS message on the DCCH using AM RLC if it receives a DOWNLINK DIRECT TRANSFER message whi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.2.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH_FACH (state 6-6) or PS_DCCH_FACH (state 6-8) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in the CELL_FACH state. The SS transmits an invalid DOWNLINK DIRECT TRANSFER message to the UE. The UE... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.2.5 Test requirement | After step 1 the UE shall transmit an RRC STATUS message on the DCCH using AM RLC setting "Message extension not comprehended" in IE "Protocol error cause" and "DOWNLINK DIRECT TRANSFER" in IE "Received message type".
After step 3 the UE shall transmit a n RRC STATUS message on the DCCH using AM RLC setting "Message no... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.3 Measurement Report on INITIAL DIRECT TRANSFER message and UPLINK DIRECT TRANSFER message | 8.1.6.3.1 Definition |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.3.2 Conformance requirement | In CELL_FACH state, the UE shall:
1> include a measurement report in the IE "Measured results on RACH", as specified in the IE "Intra-frequency reporting quantity for RACH reporting" and the IE "Maximum number of reported cells on RACH" in System Information Block type 12 (or "System Information Block Type 11" if "Syst... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.3.3 Test Purpose | To confirm that the UE reports measured results on RACH messages, if it receives IE "Intra-frequency reporting quantity for RACH reporting" and IE "Maximum number of reported cells on RACH" from System Information Block Type 11 or 12 upon a transition from idle mode to CELL_FACH state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.3.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: "Registered idle mode on PS" (state 3) in cell 1 as specified in clause 7.4 of TS 34.108. If the UE supports both CS and PS domains, the initial UE state shall be "Registered idle mode on CS/PS" (state 7).
Related ICS/IXIT statement(s)
- Support of automatic PS attach proc... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.3.5 Test Requirement | After step 2 the UE shall transmit a RRC CONNECTION REQUEST message which includes IE "measured results on RACH", containing the measurement value for cell 1's CPICH RSCP (FDD mode) or PCCPCH RSCP (TDD mode).
After step 5 the UE shall transmit a INITIAL DIRECT TRANSFER ( SERVICE REQUEST) message which includes IE "meas... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.4 UPLINK Direct Transfer (RLC re-establishment) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.4.2 Conformance requirement | If signalling radio bearer RB n (where n equals to 3 or 4) was used when transmitting the UPLINK DIRECT TRANSFER message and a re-establishment of RLC on same signalling radio bearer RB n occurs before the successful delivery of the UPLINK DIRECT TRANSFER message has been confirmed by RLC, the UE shall:
1> retransmit t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.4.3 Test purpose | To confirm that the UE transmits a second UPLINK DIRECT TRANSFER message after the re-establishment of RLC on RB3 which occurs before the successful delivery of the first UPLINK DIRECT TRANSFER message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.4.4 Method of test | Initial Condition
System Simulator: 1 cell – Cell 1 is active.
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108.
Specific Message Contents
For RRC CONNECTION SETUP message to be transmitted in the initial setup, use the default message given in TS 34.108 subclause 9 with the following exception... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.4.5 Test requirement | After step 3, the UE shall transmit UTRAN MOBILITY INFORMATION CONFIRM message using uplink DCCH on AM RLC and then retransmit UPLINK DIRECT TRANSFER message on the uplink DCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.5 Initial Direct Transfer: Inclusion of establishment cause | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.5.1 Definition | 8.1.6.5.2 Conformance requirement
In the UE, the initial direct transfer procedure shall be initiated, when the upper layers request establishment of a signalling connection. This request also includes a request for the transfer of a NAS message.
Upon initiation of the initial direct transfer procedure the UE shall:
1... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.5.3 Test purpose | To confirm that, in the case the UE wants to start a new signalling connection while the UE is already in CELL_DCH state, the UE shall include the IE “Establishment cause” in the Initial Direct Transfer message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.5.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH DCH (state 6-10) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE supports PS+CS
Test Procedure
The UE has a PS radio bearer set up in CELL_DCH state. Then, the test operator is prompted to make an out-going CS call. The... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.6.5.5 Test requirements | At step 2, the UE shall transmit an Initial Direct Transfer message with the IE “Establishment cause” set to “Originating conversational call”. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7 Security mode command | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.1 Security mode command in CELL_DCH state (CS Domain) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.1.2 Conformance requirement | 1. This procedure is used to trigger or start of ciphering or to command the restart of ciphering with the new ciphering configuration for the signalling radio bearers and any radio bearers of a particular CN Domain. It is also used to start integrity protection or modify integrity protection configuration for the sign... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.1.3 Test purpose | To confirm that the UE activates the new ciphering configurations after the stated activation time. To confirm that after the UE receives a SECURITY MODE COMMAND message, it transmits a SECURITY MODE COMPLETE message to the UTRAN using the old ciphering configuration together with the application of the new integrity p... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.1.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_DCH (state 6-9) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_DCH state. The SS initiates an Authentication procedure, which will result in the generation of a new security keyset (CK/IK). The SS transmits a SECURITY MODE COMMAND message w... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.1.5 Test requirement | After step 2 the UE shall transmit a SECURITY MODE FAILURE message to report the protocol error detected in the first SECURITY MODE COMMAND message.
After step 4 the UE shall transmit a SECURITY MODE FAILURE message to report on the invalid configuration detected in the second SECURITY MODE COMMAND message.
After step ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.2 Security mode command in CELL_FACH state | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.2.2 Conformance requirement | 1. This procedure is used to trigger the start of ciphering, or to command the restart of ciphering with the new ciphering configuration for the signalling radio bearers and any radio bearers of a particular CN Domain. It is also used to start integrity protection or modify integrity protection configuration for signal... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.2.3 Test purpose | To confirm that after the UE receives a SECURITY MODE COMMAND message, it transmits a SECURITY MODE COMPLETE message to the UTRAN using the old ciphering configuration together with the application of the new integrity protection configuration. To confirm that the UE applies the old ciphering configuration in the downl... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.2.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. The SS initiates an Authentication and Ciphering procedure, which will result in the generation of a new security keyset (CK/IK). The SS transmits a SECURITY MODE ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.2.5 Test requirement | After step 2 the UE shall transmit a SECURITY MODE FAILURE message to report the protocol error detected in the first SECURITY MODE COMMAND message.
After step 8 the SS checks that the SECURITY MODE COMPLETE message is received ciphered using the old configuration and that the calculated MAC-I values in "integrity chec... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.3 Security mode command in CELL_DCH state (UEA2/UIA2, CS Domain) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.3.1 Definition | Applicable to all Rel-7 UEs which support FDD and CS domain services. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.3.2 Conformance requirement | Same conformance requirement as clause 8.1.7.1.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.3.3 Test purpose | Same test purpose as clause 8.1.7.1.3 except that ciphering algorithm used is UEA2 and integrity protection algorithm used is UIA2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.3.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_DCH (state 6-9) as specified in clause 7.4 of TS 34.108.
Test Procedure
Same test procedure as clause 8.1.7.1.4 except that ciphering algorithm used is UEA2 and integrity protection algorithm used is UIA2.
Expected sequence
Same expected sequence as clause 8.1.7.1.4
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.3.5 Test requirement | After step 2 the UE shall transmit a SECURITY MODE FAILURE message to report the protocol error detected in the first SECURITY MODE COMMAND message.
After step 4 the UE shall transmit a SECURITY MODE FAILURE message to report on the invalid configuration detected in the second SECURITY MODE COMMAND message.
After step ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.