hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.56.3 Test purpose | To confirm that the UE reconfigures radio bearer parameters, transits from CELL_DCH to CELL_PCH state, and stops E-DCH / DPCCH discontinuous transmission and HS-DSCH reception according to the received RADIO BEARER RECONFIGURATION message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.56.4 Method of test | Initial Condition
System Simulator: 1 cell
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS_DCCH+DTCH E_DCH/HS_DSCH (state 6-18) under condition A20 as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE supports DPCCH Discontinuous Transmission
Test Proced... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.56.5 Test requirements | After step 1, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.57 Radio Bearer Reconfiguration from CELL_DCH to CELL_DCH: Success (Reconfiguration between fixed and flexible AM RLC, Serving HS-DSCH cell change between MAC-hs and MAC-ehs) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.57.1 Definition and applicability | All UEs which support FDD or 1.28Mcps TDD and MAC-ehs. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.57.2 Conformance requirement | Upon reception of the IE "RLC Info", the UE shall:
[…]
1> if the IE "Downlink RLC mode" is present and is set to "AM RLC":
2> if IE "DL RLC PDU size" is not present:
3> determining the downlink RLC PDU size will be handled at RLC level as described in [16], without any configuration from RRC.
NOTE: The case where this ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.57.3 Test purpose | 1. To verify that the UE is able to successfully perform an AM data RB reconfiguration from fixed RLC to flexible RLC, and that:
a. When the RLC Length Indicator size is unchanged, the RLC AM entity is not re-established.
b. When the RLC Length Indicator size is changed, the RLC AM entity is re-established.
2. To verif... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.57.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 is active and Cell 2 is inactive.
UE: PS_DCCH+DTCH E_DCH/HS_DSCH (state 6-18) under condition A14 (FDD)/A13(1.28Mcps TDD), as specified in clause 7.4 of TS 34.108.
System Information Block type 11 (Cell 1)
Use the same message sub-type found in clause 6.1 of TS 34.10... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.57.5 Test requirements | After step 2, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC (verifies test purpose 3a).
After step 4, the UE shall transmit a UE CAPABILITY INFORMATION message on the uplink DCCH using AM RLC (verifies test purpose 1a).
After step 8, the UE shall transmit a RADIO ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.58 Radio Bearer Reconfiguration for transition from CELL_DCH to CELL_DCH: Success (Reconfigurations between CS voice over DCH and CS voice over HSPA) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.58.1 Definition and applicability | All UEs which support FDD and CS voice over HSPA. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.58.2 Conformance requirement | If the IE "RAB information for setup" is included, the procedure is used to establish or establish/release (only if CS domain RAB mapping is reconfigured between DCH and EDCH/HSPA) radio bearers belonging to a radio access bearer, and the UE shall:
1> if the radio access bearer identified with the IE "RAB info" does no... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.58.3 Test purpose | 1 To confirm that the UE reconfigures CS domain RAB mapping from DCH to EDCH/HSPA according to the received RADIO BEARER SETUP message.
2 To confirm that the UE reconfigures CS domain RAB mapping from EDCH/HSPA to DCH according to the received RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.58.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: CS-DCCH+DTCH_DCH (state 6-9) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE supports CS voice over HSPA
Test Procedure
The UE is in CELL_DCH state.
The SS transmits a RADIO BEARER SETUP message including the RAB Information fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.58.5 Test requirements | After step 1, the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
After step 3, the UE shall transmit a RADIO BEARER SETUP COMPLETE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.59 Radio Bearer Reconfiguration from Cell FACH ( Cell supporting HS-DSCH in Cell FACH) to CELL_FACH( Cell not supporting HS-DSCH in Cell FACH): Success (Cell re-selection) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.59.1 Definition and applicability | All UEs which support FDD and HS-PDSCH in CELL_FACH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.59.2 Conformance requirement | If the UE performs cell re-selection during the reconfiguration procedure, the UE shall:
1> initiate a cell update procedure, as specified in subclause 8.3.1;
1> continue with the reconfiguration procedure.
The UE shall transmit a response message as specified in TS 25.331 subclause 8.2.2.4, setting the information ele... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.59.3 Test purpose | 1. To confirm that the UE stops HS-DSCH reception, starts FACH reception on S-CCPCH, and transmits RADIO BEARER RECONFIGURATION COMPLETE message in cell 2 when a cell re-selection occurs after receiving a RADIO BEARER RECONFIGURATION message via HS-DSCH in CELL_FACH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.59.4 Method of test | Initial Condition
System Simulator: 2 cells: Cell 1 configures HS-DSCH for CELL_FACH in System Information Type 5/5bis, Cell 2 sends the default system information (HS-DSCH for CELL_FACH not configured)
UE:CELL_FACH state as specified in clause 7.4 of TS 34.108, with a valid H-RNTI
Related ICS/IXIT statement(s)
- UE s... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.59.5 Test requirement | After step 2 the UE shall transmit a CELL UPDATE message on the CCCH with IE "cell update cause" set to "cell reselection" and “HS-PDSCH in CELL_FACH” set to TRUE.
After step 5 the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the DCCH using AM RLC.
The UE shall transmit a RADIO BEARER RECONFIGURATI... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.60 Radio Bearer Reconfiguration for transition from CELL_DCH to CELL_FACH and CELL_FACH to CELL_DCH: Success (with HS-DSCH reception in Enhanced FACH DL) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.60.1 Definition and applicability | All UEs which support FDD, fully support F-DPCH and HS-PDSCH in CELL_FACH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.60.2 Conformance requirement | If after state transition the UE enters CELL_FACH state, the UE shall, after the state transition:
1> if the IE "Frequency info" is included in the received reconfiguration message:
2> select a suitable UTRA cell according to [4] on that frequency;
2> if the UE finds a suitable UTRA cell on that frequency:
3> if the re... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.60.3 Test purpose | 1 To confirm that the UE reconfigures radio bearer parameters, transits from CELL_DCH to CELL_FACH state and back again, according to the received RADIO BEARER RECONFIGURATION message.
2 To confirm that the UE reconfigures radio bearer parameters and transits from CELL_FACH to CELL_DCH state, and starts E-DCH transmis... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.60.4 Method of test | Initial Condition
System Simulator: 1 cell
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE supports HS-PDSCH in CELL_FACH
- UE supports E-DPDCH (FDD only)
- UE fully supports F-DPCH... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.60.5 Test requirements | After step 3, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message.
After step 5, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message.
8.2.2.60a Radio Bearer Reconfiguration for transition from CELL_DCH to CELL_FACH and CELL_FACH to CELL_DCH: Success (with ongoing E-DCH transmission a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.61 Radio Bearer Reconfiguration from CELL_DCH to CELL_DCH: Success (Reconfiguration between fixed and flexible AM RLC, Serving E-DCH cell change between MAC-e/es and MAC-i/is) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.61.1 Definition and applicability | All UEs which support FDD or 1.28Mcps TDD and MAC-i/is |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.61.2 Conformance requirement | 1> if the uplink RLC PDU size is set to "flexible size" and no uplink RLC PDU size is currently set in the RLC entity:
2> configure the corresponding RLC entity with the RLC length indicator size indicated in the IE "Length indicator size".
1> if the uplink RLC PDU size is changed from "fixed" to "flexible size" and th... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.61.3 Test purpose | 1. To verify that the UE is able to successfully perform an AM data reconfiguration from fixed RLC to flexible RLC, and that:
a. When the RLC Length Indicator size is unchanged, the RLC AM entity is not re-established.
b. When the RLC Length Indicator size is changed, the RLC AM entity is re-established.
2. To verify t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.61.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 is active and Cell 2 is inactive.
The generic procedure for Radio Bearer establishment (clause 7.1.3 of TS 34.108) is executed, with all the parameters as specified in the procedure, with the exception that the default Radio Bearer is replaced with the RB according t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.61.5 Test requirements | At step 3, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC (verifies test purpose 3a).
At step 5, the UE shall transmit loopback PDU to verify the flexible RLC configuration for uplink using AM data (verifies test purpose 1a).
At step 8, the UE shall transmit a R... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.62 Radio Bearer Reconfiguration for transition from CELL_DCH to CELL_DCH: Success (activation and deactivation of MIMO) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.62.1 Definition and applicability | All UE categories which support MIMO |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.62.2 Conformance requirement | If the UE receives an ACTIVE SET UPDATE, CELL UPDATE CONFIRM, or any reconfiguration message:
1> if the IE "MIMO parameters" is not included:
2> clear the MIMO_PARAMS variable;
2> trigger lower layers to stop operation in MIMO mode.
1> otherwise:
2> for FDD, if the IE "MIMO N_cqi_typeA/M_cqi ratio" is included:
3> stor... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.62.3 Test purpose | 1. To confirm that the UE reconfigures the radio bearer parameters and starts MIMO reception according to the received RADIO BEARER SETUP message.
2. To confirm that the UE configures the physical channels to stop MIMO reception according to the received PHYSICAL CHANNEL RECONFIGURATION message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.62.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE supports MIMO
Test Procedure
The UE is in CELL_DCH state and only signalling radio bearers have been established.
The SS transmits a RADIO BEARER SETUP mes... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.62.5 Test requirements | At step 2, the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
At step 3, the UE shall transmit CQI reports of type A and type B.
At step 5 and step 11, the UE shall transmit UE CAPABILITY INFORMATION using AM RLC.
At step 8, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.63 Radio Bearer Reconfiguration from CELL_DCH to CELL_DCH: Success (activation and de-activation of 64QAM) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.63.1 Definition and Applicability | All UEs which support FDD ,mac-ehs and 64QAM |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.63.2 Conformance Requirement | In case the procedure was triggered by reception of a RADIO BEARER RECONFIGURATION message, the UE shall:
1> transmit a RADIO BEARER RECONFIGURATION COMPLETE as response message on the uplink DCCH using AM RLC.
Extract From 25.331 clause 8.6.6.36:
If the IE "Downlink HS-PDSCH Information" is included and the UE would b... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.63.3 Test purpose | 1. To confirm that the UE starts HS-DSCH transmission using DL 64QAM mode according to RADIO BEARER RECONFIGURATION message on DCCH.
2. To confirm that the UE stops HS-DSCH transmission using DL 64QAM mode according to RADIO BEARER RECONFIGURATION message on DCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.63.4 Method of test | Initial conditions
System Simulator:
UE: PS_DCCH+DTCH E_DCH/HS_DSCH (state 6-18) under condition A17b, as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE supports mac-ehs
- UE supports 64QAM
Test Procedure
The UE is initially in CELL_DCH state with the SRBs and a PS RAB mapped... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.63.5 Test requirements | After step 1 the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC.
At step 3 the UE should receive UE CAPABILITY ENQUIRY mapped on DL 64QAM HS-DSCH-mac-ehs
At step 5 the UE should receive UE CAPABILITY INFORMATION CONFIRM mapped on DL 64QAM HS-DSCH-mac-ehs
At step 7 the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.64 Radio Bearer Reconfiguration for transition from CELL_DCH to CELL_DCH: Success (simultaneous activation and deactivation of 64QAM and MIMO) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.64.1 Definition and applicability | UE category supports combined 64QAM and MIMO activation. UE support FDD and F-DPCH or Enhanced F-DPCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.64.2 Conformance requirement | If the UE receives an ACTIVE SET UPDATE, CELL UPDATE CONFIRM, or any reconfiguration message:
1> if the IE "MIMO parameters" is not included:
2> clear the MIMO_PARAMS variable;
2> trigger lower layers to stop operation in MIMO mode.
1> otherwise:
2> for FDD, if the IE "MIMO N_cqi_typeA/M_cqi ratio" is included:
3> stor... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.64.3 Test purpose | 3. To confirm that the UE reconfigures the radio bearer parameters and starts simultaneous 64QAM and MIMO reception according to the received RADIO BEARER SETUP message.
4. To confirm that the UE configures the physical channels to stop simultaneous 64QAM and MIMO reception according to the received PHYSICAL CHANNEL RE... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.64.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE category supports combined 64QAM and MIMO
- UE supports F-DPCH or Enhanced F-DPCH
Test Procedure
The UE is in CELL_DCH state and only signalling radio bear... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.64.5 Test requirements | At step 2, the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
At step 3, the UE shall transmit CQI reports of type A and type B.
At step 5 and step 11, the UE shall transmit UE CAPABILITY INFORMATION using AM RLC.
At step 8, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.65 Radio Bearer Reconfiguration for transition from CELL_DCH to CELL_FACH (Enhanced UL/DL) Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.65.1 Definition and applicability | UE supports FDD and Enhanced Uplink in CELL_FACH state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.65.2 Conformance requirement | Extract from 25.331
If variable READY_FOR_COMMON_EDCH is set to TRUE the UE shall:
1> configure and use the MAC and the physical layer for the PRACH preamble transmission according to the parameters included in the selected "PRACH preamble control parameters (for Enhanced Uplink)" IE according [15];
1> compile a list o... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.65.3 Test Purpose | 1. To confirm that the UE successfully transits to Enhanced CELL_FACH state (common E-DCH / HS-DSCH) from CELL_DCH, according to the received RADIO BEARER RECONFIGURATION message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.65.4 Method of test | Initial Conditions
System Simulator: 1 cell.
UE: PS-DCCH+DTCH DCH (state 6-10) as specified in clause 7.4 of TS 34.108 with SRB and user plane mappings on E-DCH /HS-DSCH under condition A30 RADIO BEARER SETUP.
The SS transmits SIB5 with common E-DCH/HS-DSCH information.
Related ICS/IXIT statement(s)
- UE supports FDD
-... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.65.5 Test requirements | After step 1, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message.
At step 4, the UE shall be in Enhanced CELL_FACH state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.66 Radio Bearer Reconfiguration for transition from CELL_FACH to CELL_DCH and CELL_DCH to CELL_FACH: Success (start and stop of SPS operation) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.66.1 Definition and applicability | All UEs which support TDD and SPS operation. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.66.2 Conformance requirement | If the UE receives:
- a RADIO BEARER SETUP message; or
- a RADIO BEARER RECONFIGURATION message; or
- a RADIO BEARER RELEASE message; or
- a TRANSPORT CHANNEL RECONFIGURATION message; or
- a PHYSICAL CHANNEL RECONFIGURATION message; or
…
it shall:
…
1> for 1.28 Mcps TDD, if the IE "SPS information" is stored in the UE:... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.66.3 Test purpose | 1 To confirm that the UE reconfigures radio bearer parameters, transits from CELL_DCH to CELL_FACH state, and stops SPS operation according to the received RADIO BEARER RECONFIGURATION message.
2 To confirm that the UE reconfigures radio bearer parameters, transits from CELL_FACH to CELL_DCH state, and starts SPS oper... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.66.4 Method of test | Initial Condition
System Simulator: 1 cell
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports 1.28Mcps TDD
- UE supports HS-PDSCH in CELL_FACH
- UE supports E-DCH
- UE supports SPS operation
Te... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.66.5 Test requirements | After step 3, the UE shall transmit a RADIO BEARER RECONFIGURATION.
After step 5, the UE shall transmit a UE CAPABILITY INFORMATION message without SPS operation.
After step 8, the UE shall transmit a RADIO BEARER RECONFIGURATION.
After step 10, the UE shall transmit a UE CAPABILITY INFORMATION message with SPS operati... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.67 Radio Bearer Reconfiguration for transition from CELL_FACH to CELL_DCH and CELL_DCH to CELL_FACH: Success (start and stop of Control Channel DRX operation) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.67.1 Definition and applicability | All UEs which support TDD and Control Channel DRX operation. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.67.2 Conformance requirement | If the UE receives:
- a RADIO BEARER SETUP message; or
- a RADIO BEARER RECONFIGURATION message; or
- a RADIO BEARER RELEASE message; or
- a TRANSPORT CHANNEL RECONFIGURATION message; or
- a PHYSICAL CHANNEL RECONFIGURATION message; or
…
it shall:
…
1> for 1.28 Mcps TDD, if the IEs "Control Channel DRX Information" is ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.67.3 Test purpose | 1 To confirm that the UE reconfigures radio bearer parameters, transits from CELL_DCH to CELL_FACH state, and stops Control Channel DRX operation according to the received RADIO BEARER RECONFIGURATION message.
2 To confirm that the UE reconfigures radio bearer parameters, transits from CELL_FACH to CELL_DCH state, and... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.67.4 Method of test | Initial Condition
System Simulator: 1 cell
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports 1.28Mcps TDD
- UE supports HS-PDSCH in CELL_FACH
- UE supports E-DCH
- UE supports Control Channel ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.67.5 Test requirements | After step 3, the UE shall transmit a RADIO BEARER RECONFIGURATION.
After step 5, the control channel DRX operation has not been activated.
After step 6, the UE shall transmit a RADIO BEARER RECONFIGURATION.
After step 8, the control channel DRX operation has been activated successfully. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.68 Radio Bearer Reconfiguration for transition between CELL_FACH & CELL_DCH: Success (simultaneous activation and deactivation of Dual-Cell and MIMO) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.68.1 Definition and applicability | All UE categories which support combination of DC-HSDPA and MIMO. UE supports FDD and F-DPCH or Enhanced F-DPCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.68.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RECONFIGURATION message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (for FDD only);
1> act upon all received... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.68.3 Test purpose | 5. To confirm that the UE configures the physical channels, transits from CELL_DCH to CELL_FACH, and to stop simultaneous Dual-Cell, MIMO and 16QAM reception according to the received RADIO BEARER RECONFIGURATION message.
6. To confirm that the UE reconfigures the radio bearer parameters, transits from CELL_FACH to CEL... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.68.4 Method of test | Initial Condition
System Simulator: 2 cells –Cell 1/2 DC HSDPA cell(s) with Cell 1 (Anchor Carrier) and Cell 2 (Secondary Carrier)
UE: CELL_DCH (state 6-18 PS-DCCH+DTCH E-DCH/HS-DSCH) under the condition A31 as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE category supports ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.68.5 Test requirements | At step 2, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message.
At step 5, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message.
At step 6, the UE shall on each stream on both Cell 1 and Cell 2 transmit composite CQI reports.
8.2.2.68a Radio Bearer Reconfiguration for transition betwe... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.69 Radio Bearer Reconfiguration for transition between CELL_FACH & CELL_DCH: Success (simultaneous activation and deactivation of Dual-Cell, MIMO and 64QAM) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.69.1 Definition and applicability | All UE categories which support combination of 64QAM, DC-HSDPA and MIMO. UE supports FDD and F-DPCH or Enhanced F-DPCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.69.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RECONFIGURATION message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (for FDD only);
1> act upon all received... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.69.3 Test purpose | 1. To confirm that the UE configures the physical channels, transits from CELL_DCH to CELL_FACH, and to stop simultaneous 64QAM, Dual-Cell and MIMO reception according to the received RADIO BEARER RECONFIGURATION message.
2. To confirm that the UE reconfigures the radio bearer parameters, transits from CELL_FACH to CEL... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.69.4 Method of test | Initial Condition
System Simulator: 2 cells –Cell 1/2 DC HSDPA cell(s) with Cell 1 (Anchor Carrier) and Cell 2 (Secondary Carrier)
UE: CELL_DCH (state 6-18 PS-DCCH+DTCH E-DCH/HS-DSCH) under the condition A32 as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE category supports ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.69.5 Test requirements | At step 2, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message.
At step 5, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message.
At step 6, the UE shall on each stream on both Cell 1 and Cell 2 transmit composite CQI reports.
8.2.2.69a Radio Bearer Reconfiguration for transition betwe... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.70 Radio Bearer Reconfiguration for transition from CELL_DCH to CELL_DCH with PCI Restrictions and S-CPICH Power Offset IEs: Success (64QAM +MIMO) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.70.1 Definition and applicability | All UE categories which support combined 64QAM and MIMO.
UE supports FDD and F-DPCH or Enhanced F-DPCH |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.70.2 Conformance requirement | If the UE receives an ACTIVE SET UPDATE, CELL UPDATE CONFIRM, or any reconfiguration message:
1> if the IE "MIMO parameters" is not included:
2> clear the MIMO_PARAMS variable;
2> trigger lower layers to stop operation in MIMO mode.
1> otherwise:
2> for FDD, if the IE "MIMO N_cqi_type A/M_cqi ratio" is included:
3> sto... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.70.3 Test purpose | 1. To confirm that the UE configures the lower layers with PCI restriction and S-CPICH Power offset IEs as signalled in RADIO BEARER SETUP message.
2. To confirm that the UE retains the PCI restriction and S-CPICH Power offset IEs when MIMO operation is set to “continue” according to the received RADIO BEARER RECONFIGU... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.70.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH DCH (state 6-7) under condition A28 as specified in clause 9 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE category supports combined 64QAM and MIMO
- UE supports F-DPCH or Enhanced F-DPCH
Test Procedure
Table 8.2.2.70-1
Parameter
Unit
Tx0-Rx0
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.70.5 Test requirements | At step 2, the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
At step 3 and step 9, the UE shall transmit CQI reports of type A and type B. PCI values of 0 or 3 shall be used by the UE for type A CQIs where one transport block is preferred. For type A CQIs where two transport blocks are preferred, the restric... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.71 Radio Bearer Reconfiguration for transition from CELL_DCH to CELL_DCH with PCI Restrictions and S-CPICH Power Offset IEs: Success (16QAM +MIMO) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.71.1 Definition and applicability | All UE categories which support MIMO.
UE supports FDD and F-DPCH or Enhanced F-DPCH |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.71.2 Conformance requirement | If the UE receives an ACTIVE SET UPDATE, CELL UPDATE CONFIRM, or any reconfiguration message:
1> if the IE "MIMO parameters" is not included:
2> clear the MIMO_PARAMS variable;
2> trigger lower layers to stop operation in MIMO mode.
1> otherwise:
2> for FDD, if the IE "MIMO N_cqi_type A/M_cqi ratio" is included:
3> sto... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.71.3 Test purpose | 1. To confirm that the UE configures the lower layers with PCI restriction and S-CPICH Power offset IEs as signalled in RADIO BEARER SETUP message.
2. To confirm that the UE retains the PCI restriction and S-CPICH Power offset IEs when MIMO operation is set to “CONTINUE” according to the received RADIO BEARER RECONFIGU... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.71.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE category supports MIMO
- UE supports F-DPCH or Enhanced F-DPCH
Test Procedure
Table 8.2.2.71-1
Parameter
Unit
Tx0-Rx0
Tx1-Rx1
CPICH Ec (FDD)
dBm/3.84MHz
-6... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.71.5 Test requirements | At step 2, the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
At step 3 and step 9, the UE shall transmit CQI reports of type A and type B. PCI values of 0 or 3 shall be used by the UE for type A CQIs where one transport block is preferred. For type A CQIs where two transport blocks are preferred, the restric... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.72 Radio Bearer Reconfiguration for S-CPICH based MIMO with DPCH in STTD: (16QAM +MIMO) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.72.1 Definition and applicability | All UE categories which support MIMO.
UE supports FDD and F-DPCH or Enhanced F-DPCH |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.72.2 Conformance requirement | If the UE receives an ACTIVE SET UPDATE, CELL UPDATE CONFIRM, or any reconfiguration message:
1> if the IE "MIMO parameters" is not included:
2> clear the MIMO_PARAMS variable;
2> trigger lower layers to stop operation in MIMO mode.
1> otherwise:
2> for FDD, if the IE "MIMO N_cqi_type A/M_cqi ratio" is included:
3> sto... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.72.3 Test purpose | 1. To confirm that the UE configures the radio bearer parameters and starts MIMO reception according to the received RADIO BEARER SETUP message and configures layer 1 to use STTD as Tx diversity mode for F-DPCH.
2. To confirm that the UE configures the radio bearers to stop MIMO reception according to the received RADI... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.72.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE category supports MIMO
- UE supports F-DPCH or Enhanced F-DPCH
Test Procedure
The UE is in CELL_DCH state and only signalling radio bearers have been estab... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.72.5 Test requirements | At step 2, the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
At step 3, the UE shall transmit CQI reports of type A and type B as per the signalled N_M ratio.
At step 5, 11 and 17 the UE shall transmit UE CAPABILITY INFORMATION using AM RLC.
At step 8 and 14, the UE shall transmit a RADIO BEARER RECONFIGURAT... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.73 FFS | 8.2.2.74 Radio Bearer Reconfiguration for transition between CELL_FACH & CELL_DCH: Success Activation and Deactivation of Dual-Cell for different band. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.