hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.10.3 Test purpose | To test the behaviour of the UE in case of procedure collision. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.10.4 Method of test | Proc 1: Test procedure 1
Initial condition
System Simulator:
Two cells, cell A in MCC1/MNC1/LAC1/RAC1 (RAI-1), cell B in MCC1/MNC1/LAC1/RAC2 (RAI-4).
Both cells are operating in network operation mode I.
User Equipment:
The UE has a valid IMSI.
Related ICS/IXIT statements
Support of PS service Yes/No
UE operation mode... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.10.5 Test requirements | Test requirements for Test procedure 1
At step3, when the UE is powered up or switched on, UE shall:
- initiate the combined PS attach procedure with the information elements specified in the above Expected Sequence.
At step8, when the RF level of the attached cell is lower than the RF level of the new cell, UE shall:
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.11 Combined routing area updating / abnormal cases / access barred due to domain specific access restriction for CS domain | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.11.1 Definition | This test case is applicable for Rel-5 UEs supporting DSAC and Rel-6 or later UEs. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.11.2 Conformance requirement | If the PS or CS domain is barred because of domain specific access control, a GPRS MS operating in mode A or B in a network that operates in mode I shall act as if in network operation mode II or III (depending on whether a PCCCH is present in Gb-mode) and access to the barred domain shall be stopped entirely. If the M... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.11.3 Test purpose | To test the behaviour of the UE in case of domain specific access control for CS domain. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.11.4 Method of test | Initial condition
An access class x (0-15) is arbitrarily chosen. The USIM is programmed with this access class x.
The SS informs the UE that the CS domain specific access class x is barred in the cell B.
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1 (RAI-1) has CS domain sp... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.11.5 Test requirements | At step15, when the SS indicates that PS domain specific access class x is barred, the UE shall:
- perform the normal (non combined) routing area updating procedure.
At step23, when the SS indicates that PS domain specific access class x is not barred, the UE shall:
- perform the combined routing area updating procedur... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.12 Combined routing area updating / abnormal cases / access barred due to domain specific access restriction for PS domain | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.12.1 Definition | This test case is applicable for Rel-5 UEs supporting DSAC and Rel-6 or later UEs. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.12.2 Conformance requirement | TS24.008 clause 4.1.1.2.1
If the PS or CS domain is barred because of domain specific access control, a GPRS MS operating in mode A or B in a network that operates in mode I shall act as if in network operation mode II or III (depending on whether a PCCCH is present in Gb-mode) and access to the barred domain shall be ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.12.3 Test purpose | To test the behaviour of the UE in case of domain specific access class control for PS domain. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.12.4 Method of test | Initial condition
An access class x (0-15) is arbitrarily chosen. The USIM is programmed with this access class x.
The SS informs the UE that that the PS domain specific access class x is barred in the cell B.
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1 (RAI-1) has PS domai... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.2.12.5 Test requirements | At step14, when the SS indicates PS domain specific access class x is barred, the UE shall:
- perform the normal location area updating procedure.
At step19, when the SS indicates PS domain specific access class x is not barred, the UE shall:
- perform the combined routing area updating procedure with IMSI attach. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3 Periodic routing area updating | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.1 Periodic routing area updating / accepted | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.1.2 Conformance requirement | The User Equipment shall perform a periodic routing area update procedure after a T3312 timeout.
Reference
3GPP TS 24.008 clauses 4.7.2.2 and 4.7.5.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.1.3 Test purpose | To test the behaviour of the UE with respect to the periodic routing area updating procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.1.4 Method of test | Initial condition
System Simulator:
One cell operating in network operation mode II (in case of UE operation mode A).
The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 value is set to 0 and ATT flag is set to FALSE).
User Equipment:
The UE has a valid P-TMSI-1 an... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.1.5 Test requirements | At step3, when the UE is powered up or switched on, UE shall:
- initiate the PS attach procedure with the information elements specified in the above Expected Sequence.
At step6, when the timer T3312 is expired, UE shall:
- initiate the routing area updating procedure with Update type = 'Periodic updating'. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.2 Periodic routing area updating / accepted / T3312 default value | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.2.2 Conformance requirement | The User Equipment shall perform a periodic routing area update procedure after a T3312 timeout.
Reference
3GPP TS 24.008 clauses 4.7.2.2 and 4.7.5.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.2.3 Test purpose | To test the behaviour of the UE with respect to the periodic routing area updating procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.2.4 Method of test | Initial condition
System Simulator:
One cell operating in network operation mode I.
User Equipment:
The UE has a valid P-TMSI-1 and RAI-1.
Related ICS/IXIT statements
Support of PS service Yes/No
UE operation mode A Yes/No
Switch off on button Yes/No
Automatic PS attach procedure at switch on or power on Yes/No
Tes... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.2.5 Test requirements | At step3, when the UE is powered up or switched on, UE shall:
- initiate the PS attach procedure with the information elements specified in the above Expected Sequence.
At step5, when the timer T3312 is expired, UE shall:
- initiate the routing area updating procedure with Update type = 'Periodic updating'.
12.4.3.2a P... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.3 Periodic routing area updating / no cell available / network mode I | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.3.2 Conformance requirement | If the UE is both IMSI attached for PS and non-PS services, and if the UE lost coverage of the registered PLMN and timer T3312 expires; if the UE returns to coverage in a cell that supports PS and the network is in network operation mode I, then the UE shall perform a combined routing area update procedure indicating '... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.3.3 Test purpose | To test the behaviour of the UE with respect to the periodic routing area updating procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.3.4 Method of test | Initial condition
System Simulator:
Two cells, cell A in MCC1/MNC1/LAC1/RAC1 (RAI-1), cell B in MCC1/MNC1/LAC1/RAC2 (RAI-4).
Cell A is operating in network operation mode II and cell B is in network operation mode I.
User Equipment:
The UE has a valid P-TMSI-1 and RAI-1.
The UE has been registered in the CS domain.
Rel... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.3.5 Test requirements | At step4, when the UE is powered up or switched on, UE shall:
- initiate the PS attach procedure with the information elements specified in the above Expected Sequence.
At step12, when the UE is both IMSI attached for PS and non-PS service , and if the UE lost coverage of the reiterated PLMN and the timer T3312 expires... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.4 Periodic routing area updating / no cell available | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.4.2 Conformance requirement | If the UE is both IMSI attached for PS and non-PS services, and if the UE lost coverage of the registered PLMN and timer T3312 expires; if the UE returns to coverage in a cell that supports PS and the network is in network operation mode II, then the UE shall perform a periodic routing area update procedure and a perio... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.4.3 Test purpose | To test the behaviour of the UE with respect to the periodic routing area updating procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.4.4 Method of test | Initial condition
System Simulator:
One cell operating in network operation mode II.
The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 value is set to 0 and ATT flag is set to FALSE to prevent repeated CS domain registration and/or IMSI Detach by UEs in operation... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.4.3.4.5 Test requirements | At step2, when the UE is powered up or switched on, UE shall:
- initiate the PS attach procedure with the information elements specified in the above Expected Sequence.
At step16, when the UE is both IMSI attached for PS and non-PS service, and if the UE lost coverage of the reiterated PLMN and the timer T3312 expires,... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.5 P-TMSI reallocation | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.5.2 Conformance requirement | 1) A User Equipment shall acknowledge a new P-TMSI when explicitly allocated.
2) The P-TMSI shall be updated on the USIM when the User Equipment is correctly deactivated in accordance with the manufacturer's instructions.
3) A User Equipment shall use the given P-TMSI in further communication with the network.
Referenc... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.5.3 Test purpose | To verify that the UE is able to receive and acknowledge a new P-TMSI by means of an explicit P-TMSI reallocation procedure.
To verify that the UE has stored the P-TMSI in a non-volatile memory.
The implicit reallocation procedure is tested in the attach procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.5.4 Method of test | Initial condition
System Simulator:
- One cell operating in network operation mode II.
- The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 value is set to 0 and ATT flag is set to FALSE).
User Equipment:
The UE has a valid IMSI.
If the UE is in UE operation mode ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.5.5 Test requirements | At step3, when the UE is powered up or switched on, UE shall:
- initiate the PS attach procedure with the information elements specified in the above Expected Sequence.
At step7, when the UE receives P-TMSI REALLOCATION COMMAND message from SS, UE shall:
- acknowledge the new P-TMSI by sending P-TMSI REALLOCATION COMPL... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6 PS authentication | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1 Test of authentication | The purpose of this procedure is to verify the user identity. A correct response is essential to guarantee the establishment of the connection. If not, the connection will drop. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.1 Authentication accepted | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.1.2 Conformance requirement | A User Equipment shall correctly respond in an authentication and ciphering procedure by sending a response with the RES information field set to the same value as the one produced by the authentication and ciphering algorithm in the network.
Reference
3GPP TS 24.008 clause 4.7.7. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.1.3 Test purpose | To test the behaviour of the UE if the network accepts the authentication and ciphering procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.1.4 Method of test | Initial condition
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1 (RAI-1), cell B in MCC1/MNC1/LAC1/RAC2 (RAI-4).
Both cells are operating in network operation mode II.
The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 va... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.1.5 Test requirements | At steps 3a and 10a the UE shall transmit an RRC CONNECTION REQUEST message with the IE "Establishment cause" set to "Registration".
At step4, when the UE is powered on or switched on, UE shall:
- initiate the PS attach procedure with information elements specified in the above Expected Sequence.
At step6, when the UE ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.2 Authentication rejected by the network | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.2.2 Conformance requirement | Upon receipt of an AUTHENTICATION AND CIPHERING REJECT message, the UE shall set the PS update status to GU3 ROAMING NOT ALLOWED and shall delete the P-TMSI, P-TMSI signature, RAI and PS ciphering key sequence number stored.
The USIM shall be considered as invalid until switching off or the USIM is removed.
If the AUTH... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.2.3 Test purpose | To test the behaviour of the UE if the network rejects the authentication and ciphering procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.2.4 Method of test | Initial condition
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1 (RAI-1), cell B in MCC1/MNC1/LAC1/RAC2 (RAI-4).
Both cells are operating in network operation mode II.
The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 va... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.2.5 Test requirements | At step3, when the UE is powered on or switched on, UE shall:
- initiate the PS attach procedure with information elements specified in the above Expected Sequence.
At step9, when the UE receives the AUTHENTICATION AND CIPHERING REJECT message, UE shall:
- not respond paging message for PS domain.
At step13, when the R... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3 Authentication rejected by the UE | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.1 GMM cause 'MAC failure' | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.1.2 Conformance requirement | If the UE considers the MAC code (supplied by the core network in the AUTN parameter) to be invalid, the UE shall send AUTHENTICATION AND CIPHERING FAILURE message with the reject cause 'MAC failure' to the System Simulator.
Reference
3GPP TS 24.008 clause 4.7.7. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.1.3 Test purpose | To test the behaviours of the UE, when the UE considers the MAC code (supplied by the core network in the AUTN parameter) to be invalid. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.1.4 Method of test | Initial condition
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1 (RAI-1), cell B in MCC1/MNC1/LAC1/RAC2 (RAI-4).
Both cells are operating in network operation mode II.
The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 va... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.1.5 Test requirements | At step6, when the UE is powered on or switched on, UE shall:
- initiate the PS attach procedure with information element specified in the above Expected Sequence.
At step9, when the UE receives the AUTHENTICATION AND CIPHERING REQUEST with Invalid Message Authentication Code, UE shall:
- send the AUTHENTICATION AND CI... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.2 GMM cause 'Synch failure' | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.2.2 Conformance requirement | If the UE considers the SQN (supplied by the core network in the AUTN parameter) to be out of range, the UE shall send AUTHENTICATION AND CIPHERING FAILURE message with the reject cause 'Synch failure' to the System Simulator.
Reference
3GPP TS 24.008 clause 4.7.7. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.2.3 Test purpose | To test the behaviours of the UE, when the UE considers the SQN (supplied by the core network in the AUTN parameter) to be out of range. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.2.4 Method of test | Initial condition
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1 (RAI-1), cell B in MCC1/MNC1/LAC1/RAC2 (RAI-4).
Both cells are operating in network operation mode II.
The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 va... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.2.5 Test requirements | At step4, when the UE is powered on or switched on, UE shall:
- initiate the PS attach procedure with information element specified in the above Expected Sequence.
At step7, when the UE receives the AUTHENTICATION AND CIPHERING REQUEST message(SQN is out of range.), UE shall:
- send the AUTHENTICATION AND CIPHERING FAI... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.3 Authentication rejected by the UE / fraudulent network | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.3.2 Conformance requirement | R99 and REL-4:
1. It can be assumed that the source of the authentication challenge is not genuine (authentication not accepted by the UE) if any of the following occur:
- After sending the AUTHENTICATION & CIPHERING FAILURE message with GMM cause 'MAC failure' the timer T3318 expires;
- Upon receipt of the second AUTH... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.3.3 Test purpose | R99 and REL-4
To test UE treating a cell as barred:
1. when the network sends the second or third AUTHENTICATION & CIPHERING REQUEST message with invalid MAC code during the timer T3318 is running.
2. when the timer T3318 has expired.
REL-5 or later release:
To test UE treating a cell as barred:
1. when the network se... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.3.4 Method of test | Initial condition
System Simulator:
Two cells (not simultaneously activated), cell A in MCC1/MNC1/LAC1/RAC1(RAI-1), cell B in MCC1/MNC1/LAC1/RAC2(RAI-2).
Both cells are operating in network operation mode II.
The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 valu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.1.3.3.5 Test requirements | At step3, when the UE is powered on or switched on, the UE shall:
- initiate the PS attach procedure with information elements specified in the above Expected Sequence.
After step4, when the UE have received the first AUTHENTICATION AND CIPHERING REQUEST message with invalid Message Authentication Code (MAC), the UE sh... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.6.2 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.7 Identification procedure | The purpose of this procedure is to check that the UE gives its identity as requested by the network. If this procedure does not work, it will not be possible for the network to rely on the identity claimed by the UE. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.7.1 General Identification | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.7.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.7.1.2 Conformance requirement | 1) When requested by the network the User Equipment shall send its IMSI.
2) When requested by the network the User Equipment shall send its IMEI as stored in the Mobile Equipment.
3) When requested by the network the User Equipment shall send its IMEISV as stored in the Mobile Equipment.
Reference
3GPP TS 24.008 clause... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.7.1.3 Test purpose | To verify that the UE sends identity information as requested by the system. The following identities can be requested: IMSI, IMEI and IMEISV. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.7.1.4 Method of test | Initial condition
System Simulator:
One cell operating in network mode II.
The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 value is set to 0 and ATT flag is set to FALSE to prevent repeated CS domain registration and/or IMSI Detach by UEs in operation mode A).
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.7.1.5 Test requirements | At step 2a the UE shall send an RRC CONNECTION REQUEST message with the IE Establishment cause set to "Registration".
At step 12a the UE shall send an RRC CONNECTION REQUEST message with the IE Establishment cause set to "Detach".
At step3, when the UE is powered on or switched on, UE shall:
- initiate the PS attach pr... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.8 GMM READY timer handling | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.8.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.8.2 Conformance requirement | If a READY timer value is received by an UE capable of both UMTS and GSM in the ATTACH ACCEPT or the ROUTING AREA UPDATE ACCEPT messages, then the received value shall be stored by the UE in order to be used at an intersystem change from UMTS to GSM.
Reference
3GPP TS 24.008 clause 4.7.2.1 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.8.3 Test purpose | To verify that READY timer value received in UTRA can be used in GSM. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.8.4 Method of test | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.8.4.1 Test procedure | Initial condition
System Simulator:
Two cells (not simultaneously activated), cell A (UTRAN) in MCC1/MNC1/LAC1/RAC1 (RAI-1), cell B (GSM) in MCC1/MNC1/LAC1/RAC2 (RAI-4).
Parameter
Unit
Cell B
(GSM)
Qsearch_I (TDD)
dBm
15 (never)
Cell B is in neighbour cell list of cell A.
Both cells are operating in network operation m... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.8.5 Test requirements | At step4, when the UE receives the ATTACH ACCEPT or the ROUTING AREA UPDATE ACCEPT messages, UE shall:
- store the received READY timer value.
At step12, UE shall establish periodic Routing Area Update after Timer Period (T3314) + Periodic Routing Area
Updating timer (T3312) (+/- 10%). |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.9 Service Request procedure (UMTS Only) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.9.1 Service Request Initiated by UE Procedure | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.9.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.9.1.2 Conformance requirement | UE shall send the Service Request message to the network in order to establish the PS signalling connection for the upper layer signalling or for the resource reservation for active PDP context(s).
Reference
TS 24.008 clauses 4.7.13
TS 23.060 clauses 6.12.1 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.9.1.3 Test purpose | To test the behaviour of the UE if the UE initiates the CM layer service (e.g. SM or SMS) procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 12.9.1.4 Method of test | Initial condition
System Simulator:
One cell operating in network operation mode II.
The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to value "00 00" (T3212 value is set to 0 and ATT flag is set to FALSE to prevent repeated CS domain registration and/or IMSI Detach by UEs in operation... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.