hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.6.1 Conformance requirements | For the MS it is prohibited to implement algorithm A5/2.
References
3GPP TS 43.020 subclause 4.9 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.6.2 Test purpose | To verify that the MS does not start ciphering when it receives a CIPHERING MODE COMMAND message with Cipher Mode Setting = "Start Ciphering" and algorithm identifier set to "A5/2". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.6.3 Method of test | Initial Conditions
System Simulator:
1 cell. ATT=1.
Mobile Station:
Power off.
Specific PICS statements
-
PIXIT statements
-
Test Procedure
The MS is powered on. The MS sends CHANNEL REQUEST for doing location update procedure. The SS sends an IMMEDIATE ASSIGNMENT and the MS shall answer with a LOCATION UPDATING REQUES... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.7 Ciphering mode with cipher key Kc128 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.7.1 Conformance requirements | 1. When the MS receives the CIPHERING MODE COMMAND message with Ciphering Mode Setting information element set to "start ciphering", the MS starts ciphering and deciphering with the algorithm indicated by the "algorithm identifier" field:
- the MS responds with a CIPHERING MODE COMPLETE message in ciphered mode;
- the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.7.2 Test purpose | To verify that the MS calculates the correct Kc128 and starts ciphering using cipher algorithm A5/4 when it receives a CIPHERING MODE COMMAND message with Cipher Mode Setting = "Start Ciphering".
To verify that the correct Kc128 key is used after ASSIGNMENT COMMAND including cipher mode setting for A5/4 algorithm. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.7.3 Method of test | Initial Conditions
System Simulator:
1 cell, default settings.
Mobile Station:
Test USIM is plugged into the MS. The MS is in the "idle, updated" state, with a TMSI allocated.
Specific PICS statements
-
PIXIT statements
-
Foreseen Final State of the MS
CC state U10-call active.
Test Procedure
The MS is made to originat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.8 Ciphering mode with cipher key Kc128 and algorithm changes | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.8.1 Conformance requirements | 1. A ME supporting UMTS authentication challenge may support the following procedure: In order to avoid a synchronisation failure, if the same RAND is received twice, the mobile station shall store the received RAND together with the RES returned from the USIM in the volatile memory and compare it with any subsequently... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 3 The ASSIGNMENT COMMAND message may contain a cipher mode setting IE. In that case, this ciphering mode has to be applied on the new channel. If no such information is present, the ciphering mode is the same as on the previous channel. In either case the ciphering key shall not be changed as long as the key length rem... | 4 In a UMTS authentication challenge, the new UMTS ciphering key, the new GSM ciphering key and the new UMTS integrity key calculated from the challenge information shall overwrite the previous UMTS ciphering key, GSM ciphering key and UMTS integrity key. The new UMTS ciphering key, GSM ciphering key and UMTS integrity... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.8.2 Test purpose | To verify that the MS handles correctly key length changes when the SS orders the MS to change from A5/1 to A5/4 and vice versa. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.8.8.3 Method of test | Initial Conditions
System Simulator:
1 cell, default settings.
Mobile Station:
Test USIM is plugged into the MS. The MS is in the "idle, updated" state, with a TMSI allocated.
Specific PICS statements
-
PIXIT statements
-
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is page... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.9 Test of additional assignment | The Additional Assignment procedure is used to change an MS's channel configuration from Lm + ACCH to Lm + Lm + ACCH. It is therefore only relevant to those mobiles which perform such an operation.
No tests are specified at the moment. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.10 Test of partial release | The Partial Release procedure is used to change an MS's channel configuration from Lm + Lm + ACCH to Lm + ACCH. It is therefore only relevant to those mobiles which perform such an operation.
No tests are specified at the moment. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11 Test of classmark | References to Class Mark related PICS values are provided in the table 26.6.11a and 26.6.11b.
Table 26.6.11a: Mobile Station Classmark 2 information element
Item
IE
Values
Mnemonic
1
Revision level
Revision level Bits
7
6
0
0
GSM Phase 1
0
1
GSM Phase 2 MS
1
0
MS supporting R99 or later
1
1
Reserved for Future
TSPC_Rev... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 P-GSM not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 P-GSM supported | Band 2 supported
Bit 2 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 E-GSM or R-GSM not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 E-GSM or R-GSM supported | Band 3 supported
Bit 3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 GSM 1800 not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 GSM 1800 supported | TSPC_Type_GSM_P_Band
TSPC_Type_GSM_E_Band
TSPC_Type_GSM_R_Band
TSPC_Type_DCS_Band
Note: Due to the shared radio frequency channel numbers between DCS 1800 and PCS 1900, even if both DCS_1800_BAND and PCS_1900_BAND are set to TRUE, the MS can only ever indicate support for one of these bands
2
A5 bits
A5/4 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 Encryption algorithm A5/4 not available | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 Encryption algorithm A5/4 available | A5/5 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 Encryption algorithm A5/5 not available | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 Encryption algorithm A5/5 available | A5/6 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 Encryption algorithm A5/6 not available | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 Encryption algorithm A5/6 available | A5/7 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 Encryption algorithm A5/7 not available | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 Encryption algorithm A5/7 available | TSPC_Feat_A54
A5/5 Feature is not available and should set to 0
A5/6 Feature is not available and should set to 0
A5/7 Feature is not available and should set to 0
3
Associated Radio capability 1 and 2
4 bit fields
If either of P-GSM or E-GSM or R-GSM is supported, the radio capability 1 field indicates the radio capab... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 MS assisted E-OTD not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 MS assisted E-OTD supported | MS based E-OTD
Bit 4 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 MS based E-OTD not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 MS based E-OTD supported | MS assisted GPS
Bit 3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 MS assisted GPS not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 MS assisted GPS supported | MS based GPS
Bit 2 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 MS based GPS not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 MS based GPS supported | MS Conventional GPS
Bit 1
0 conventional GPS not supported
1 conventional GPS supported
TSPC_EOTD_ASSIST TSPC_EOTD_MS_BASED
TSPC_A-GPS_Assist
TSPC_A-GPS_Based
TSPC_Conv-GPS
11
ECSD Multi Slot class
An MS that supports ECSD shall include this field to indicate its ECSD capability. Whether the MS is capable of 8-PSK modu... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 8-PSK supported for downlink | reception only |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 8-PSK supported for uplink transmission and downlink reception | TSPC_8-PSK_Struct
TSPC_Type_DTM_EGPRS_8PSK_uplink TSPC_Type_ECSD_8PSK_uplink
14
8-PSK RF Power Capability 1
Bits 2 1
0 0 Reserved
0 1 Power class E1
1 0 Power class E2
1 1 Power class E3
TSPC_8-PSK_Struct
TSPC_8-PSK_PowerCap1
TSPC_Type_GSM_ClassE1
TSPC_Type_GSM_ClassE2
TSPC_Type_GSM_ClassE3
TSPC_Type_GSM_850_ClassE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 UMTS FDD not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 UMTS FDD supported | TSPC_Type_UTRAN_FDD
21
UMTS 3.84 Mcps TDD Radio Access Technology Capability |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 UMTS 3.84 Mcps TDD not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 UMTS 3.84 Mcps TDD supported | TSPC_Type_UTRAN3.84_TDD
22
CDMA 2000 Radio Access Technology Capability |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 CDMA2000 not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 CDMA2000 supported | TSPC_CDMA2000
23
DTM GPRS Multi Slot Class
Bit
2 1
0 0 Unused. If received, the
network shall interpret
this as ‘01’
0 1 Multislot class 5
supported
1 0 Multislot class 9
supported
1 1 Multislot class 11
supported
TSPC_DTM_GPRS_Multislot_Class_1
TSPC_DTM_GPRS_Multislot_Class_5
TSPC_DTM_GPRS_Multislot_Class_9
TSPC_D... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 Single Slot DTM not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 Single Slot DTM supported | TSPC_DTM_GPRS_Singleslot_Allocation
TSPC_DTM_EGPRS_Singleslot_Allocation
25
DTM EGPRS Multi Slot Class
This field indicates the DTM GPRS multislot capabilities of the MS. It is coded as follows:
Bit
2 1
0 0 Unused. If received, the network shall interpret this as ‘01’
0 1 Multislot class 5 supported
1 0 Multislot cl... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 UMTS 1.28 Mcps TDD not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 UMTS 1.28 Mcps TDD supported | TSPC_Type_UTRAN1.28_TDD
30
GERAN Feature Package 1
0 GERAN feature package 1 not supported.
1 GERAN feature package 1 supported.
TSPC_GERAN_FEATURE_PACKAGE_1
31
Extended DTM GPRS Multi Slot Class
DGMSC Bit 2 1 Bit 2 1
0 0 0 0 Unused. If received, it shall be interpreted as ‘01 00’
0 0 0 1 Unused. If received, it... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 The mobile station does not require the offset | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 The mobile station requires the offset | TSPC_Offset_Required
47
DTM EGPRS High Multi Slot Class
This field indicates the DTM EGPRS multislot capabilities of the MS. This field may be included only if the mobile station supports EGPRS DTM. This field is coded as the DTM GPRS High Multi Slot Class field. When this field is not present, the MS supports the DTM ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 The mobile station does not support Repeated SACCH | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 The mobile station supports Repeated SACCH and Repeated Downlink FACCH | An MS that only supports Repeated Downlink FACCH shall set this bit field to ‘0’.
NOTE 1)
TSPC_Repeated_SACCH
TSPC_Repeated_FACCH
49
GSM 710 Associated Radio Capability
See the semantic rule for the sending of this field.
This field indicates whether GSM 710 band is supported and its associated radio capability.
The ra... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 The mobile station does not support the Ciphering Mode Setting IE in the | DTM ASSIGNMENT COMMAND message
1 The mobile station supports the Ciphering Mode Setting IE in the DTM ASSIGNMENT COMMAND
message
TSPC_Ciphering_Mode_Setting_Cap
52
Additional Positioning Capabilities
0 The mobile station does not support additional positioning capabilities which can be retrieved using RRLP
1 The mo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 E-UTRAN Neighbour Cell measurements and measurement reporting while having an RR connection | not supported |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 E-UTRAN Neighbour Cell measurements and measurement reporting while having an RR connection | supported
TSPC_E-UTRA_Measurement_Reporting
56
Priority Based Cell Reselection
Bit |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 Priority-based cell reselection not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 Priority-based cell reselection supported | TSPC_Priority_Based_Cell_Reselection
57
UTRA CSG Cells Reporting
Bit |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 Reporting of UTRAN CSG cells not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 Reporting of UTRAN CSG cells supported | TSPC_UTRA_CSG_Cells_Reporting
58
VAMOS Level
Bits
2 1
0 0 VAMOS not supported
0 1 VAMOS I supported
1 0 VAMOS II supported
1 1 VAMOS III supported.
(NOTE 1)
TSPC_VAMOS_Type1
TSPC_VAMOS_Type2
TSPC_VAMOS_Type3
59
TIGHTER Capability
Bits
2 1
0 0 TIGHTER not supported
0 1 TIGHTER supported for speech and signalling c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 Selective Ciphering of Downlink SACCH not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 Selective Ciphering of Downlink SACCH supported | TSPC_Selective_Ciphering_DL_SACCH
61
ER Band Support
Bit |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 0 ER-GSM not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 1 ER-GSM supported | NOTE 3)
TSPC_Type_ER_GSM_Band
NOTE 1: An MS indicating support for VAMOS (Item 58) shall also indicate support for either “Downlink Advanced Receiver Performance – phase I” or “Downlink Advanced Receiver Performance – phase II” (Item 43), and for “Repeated SACCH and Repeated Downlink FACCH” (Item 48).
((TSPC_VAMOS_Type... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.1 Classmark change | This procedure allows the MS to indicate to the network that a change in the classmark (e.g. due to addition of power amplification) has taken place. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.1.1 Conformance requirements | If the RF power capability of the MS is changed during a call, this change shall be signalled to the network.
If the RF power capability of the MS is changed in idle mode, the up to date RF power capability shall be signalled to the network during RR connection establishment.
References
3GPP TS 04.08 / 3GPP TS 44.018 s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.1.2 Test purpose | To verify that if the RF power capability or any other capability indicated in a Classmark IE of the MS is changed during a call, the change is communicated on the DCCH to the network.
To verify that if the RF power capability or any other capability indicated in a Classmark IE of the MS is changed in idle mode, the ou... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and with no additional power amplification applied.
Specific PICS statements
• TSPC_Type_xxx (all appropriate power classes)
• TSPC_AddInfo_Full_rate_version_1
• TSPC_AddInfo_Fu... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.2 Classmark interrogation | This procedure allows the network to request the MS to supply all its classmark information to the network.
Networks may systematically use this procedure (e.g. during location updating) and, it if is incorrectly implemented in the MS, the basic connection establishment procedure may systematically fail. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.2.1 Conformance requirements | On receipt of a CLASSMARK ENQUIRY message, the MS sends a CLASSMARK CHANGE message to the network containing the Mobile Station Classmark 2 information element and depending upon the contents of this information element, possibly the Mobile Station Classmark 3 information element.
References
3GPP TS 04.08 / 3GPP TS 44.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.2.2 Test purpose | To verify that if the network requests the MS to supply all its classmark information then this information is communicated on the DCCH to the network. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.2.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
"Idle, updated", with TMSI allocated.
Specific PICS statements
-
PIXIT statements
-
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is switched off (or has its power removed).
The SS then sets the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.3 Classmark interrogation / UTRAN Classmark Change | This procedure allows the network to request the MS to supply all its classmark information to the network. In addition the network may request a MS supporting UTRAN to send the UTRAN classmark information.
Networks may systematically use this procedure (e.g. during location updating) and, it if is incorrectly implemen... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.3.1 Conformance requirements | On receipt of a CLASSMARK ENQUIRY message, the MS sends a CLASSMARK CHANGE message to the network containing the Mobile Station Classmark 2 information element and depending upon the contents of this information element, possibly the Mobile Station Classmark 3 information element.
References
3GPP TS 04.08 / 3GPP TS 44.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.3.2 Test purpose | To verify that if the network requests the MS to supply all its classmark information, including the UTRA Classmark information, then this information is communicated on the DCCH to the network. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.3.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters. In SI3 is ATT flag is set to 1 and Early Classmark Sending Control flag is set to Low.
Mobile Station:
Powered off.
Specific PICS statements
-
PIXIT statements
Test Procedure
The MS is switched on (or its power is re-applied). The MS then initiates a loca... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.4 Early UTRAN Classmark Sending | This procedure allows the network to request the MS to supply all its classmark information to the network. In addition the network may request a MS supporting UTRAN to send the UTRAN classmark information.
Networks may systematically use this procedure (e.g. during location updating) and, it if is incorrectly implemen... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.4.1 Conformance requirements | Early classmark sending consists in the mobile station sending as early as possible after access a CLASSMARK CHANGE message to provide the network with additional classmark information. In addition a MS supporting UTRAN sends a UTRAN Classmark Change message; an MS supporting CDMA2000 sends a CDMA2000 Classmark Change.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.4.2 Test purpose | To verify that if the network requests the MS to supply all its classmark information, including the UTRAN Classmark information, then this information is communicated on the DCCH to the network. The request of the classmark information is indicated in SYSTEM INFORMATION TYPE 3. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.11.4.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
The SS shall transmit SI3 with ATT flag is set to 1 and both Early Classmark Sending Restriction and 3G Early Classmark Sending Restriction parameter set to High.
Mobile Station:
Powered off.
Specific PICS statements
-
PIXIT statements
• Contents of Mobil... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12 Test of channel release | The purpose of this procedure is to deactivate the dedicated channels in use. When the channels are released, the MS returns to the CCCH configuration, idle mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.1 Channel release / SDCCH | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.1.1 Conformance requirements | After the acknowledgement of the Layer 2 disconnection by the network, the MS shall not produce any further RF-transmission.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.13.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.1.2 Test purpose | To verify that the MS is able to correctly release an SDCCH after having received a CHANNEL RELEASE message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated.
Specific PICS statements
-
PIXIT statements
-
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is paged and allocated a dedicated chan... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.2 Channel release / SDCCH - no L2 ACK | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.2.1 Conformance requirements | After the expiry of timer T3110 the MS shall not produce any further RF-transmission.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.13.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.2.2 Test purpose | To verify that the MS is able to correctly release a SDCCH after having received a CHANNEL RELEASE message, even if the SS does not L2 acknowledge the L2 DISC frame. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.2.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated.
Specific PICS statements
-
PIXIT statements
-
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is paged and allocated a dedicated chan... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.3 Channel release / TCH-F | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.3.1 Conformance requirements | After the acknowledgement of the Layer 2 disconnection by the network the MS shall not produce any further RF-transmission.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.13.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.3.2 Test purpose | To verify that the MS is able to correctly release a full-rate TCH after having received a CHANNEL RELEASE message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.3.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated.
Specific PICS statements
-
PIXIT statements
-
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is paged and allocated a dedicated chan... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.4 Channel release / TCH-F - no L2 ACK | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.4.1 Conformance requirements | After the expiry of timer T3110 the MS shall not produce any further RF-transmission.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.13.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.4.2 Test purpose | To verify that the MS is able to correctly release a TCH/F after having received a CHANNEL RELEASE message, even if the SS does not L2 acknowledge the L2 DISC frame. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.12.4.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated.
Specific PICS statements
-
PIXIT statements
-
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is paged and allocated a dedicated chan... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.13 Test of starting time | The Assignment, Handover and immediate assignment procedures can include a delayed change of frequency list, MAIO and HSN. This series of tests checks the behaviour of the Mobile Station when receiving channel allocation messages with a starting time and channel description for both before and after the starting time. ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.13.1 Dedicated assignment with starting time / successful case / time not elapsed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.6.13.1.1 Conformance requirement | A Mobile Station receiving an ASSIGNMENT COMMAND message with a starting time and channel descriptions for both after and before the starting time, and ready to access before the indicated time has elapsed, shall perform the assignment on the channels as described for before the starting time and shall start using the ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.