hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.3.5.9.4 Method of test | Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U8 by using table 26.8.1.3/1.
Foreseen final state of the MS
U8, connect request.
Maximum durati... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4 In call functions | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.1 In-call functions / DTMF information transfer | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.1.1 In-call functions / DTMF information transfer / basic procedures | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.1.1.1 Definition | Dual Tone Multi Frequency (DTMF) is an inband one out of four plus one out of four signalling system primarily used from terminal instruments in telecommunication networks.
The support of DTMF is only permitted when a bearer capability for speech is in use or during the speech phase of alternate speech/data and alterna... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.1.1.2 Conformance requirement | 1) An MS supporting the Mobile originating DTMF protocol control procedure, having a CC entity for speech in state U10, "Active": when made to send a DTMF tone, shall send a START DTMF message on the correct DCCH.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.3.
2) An MS supporting the Mobile originating DTM... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.1.1.3 Test purpose | 1) To verify that an MS supporting the Mobile originating DTMF protocol control procedure, having a CC entity for speech in state U10, "Active": when made to send a DTMF tone, sends a START DTMF message on the correct DCCH.
2) To verify that an MS supporting the Mobile originating DTMF protocol control procedure, havin... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.1.1.4 Method of test | Specific PICS statements
-
PIXIT statements
- supported character set (e.g. 0‑9, #, *, A, B, C, D);
- if and how DTMF tone is indicated to the user.
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in CC-state "active".
Foreseen final state of the MS
CC-state "active".
Maximum ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.2 In-call functions / user notification | User notification procedure allows the network to notify a MS of any call-related event during the "active" state of a call. It also may allow a MS to notify the remote user of any appropriate call-related event during the "active" state of a call by sending a NOTIFY message containing a notification indicator to the n... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.2.1 In-call functions / User notification / MS terminated | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.2.1.1 Definition | This is a case for testing user notification procedure terminated by the mobile station. The test is applicable for those equipments supporting at least one circuit switched basic service. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.2.1.2 Conformance requirement | 1) A CC entity of a MS in CC-state U10, "active", upon receiving of a NOTIFY message shall remain in the active state.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.2.1.3 Test purpose | To verify that a CC entity of a MS in CC-state U10, "active", upon receiving of a NOTIFY message remains in the active state. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.2.1.4 Method of test | Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in CC-state "active".
Foreseen final state of the MS
CC-state "active".
Maximum duration of test
10 s.
Test procedure
The MS being in the call active state, the SS will send a NOTIFY ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3 In-call functions / channel changes | The two following test cases are for testing some elementary radio resource level procedures during an active state of a call to ensure call maintenance also during physical channel changes. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.1 In-call functions / channel changes / a successful channel change in active state/ Handover and Assignment Command | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.1.1 Definition | This is a case to test a change of a physical channel during active state of a call. This test is applicable for any equipment supporting at least one mobile terminating circuit switched basic service. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.1.2 Conformance requirement | 1) The MS being in the call active state after having successful completed a channel assignment or a handover command, shall remain in the call active state.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.4.3.2,
3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.6.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.1.3 Test purpose | To verify that the MS being in the call active state after having successful completed a channel assignment or having completed a handover command remains in the call active state. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.1.4 Method of test | Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in CC-state "active".
Foreseen final state of the MS
CC-state "active".
Maximum duration of test
10 s.
Test procedure
The SS initiates a call to the Mobile Station, using an arbitrari... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.2 In-call functions / channel changes / an unsuccessful channel change in active mode/ Handover and Assignment Command | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.2.1 Definition | This is a case to test an unsuccessful change of a physical channel during active state of a call. This test is applicable for any equipment supporting at least one mobile terminating circuit switched basic service. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.2.2 Conformance requirement | 1) The MS, when returning to the old channel after handover or Assignment failure and having established the link, shall remain in the call active state.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.4.3. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.2.3 Test purpose | To verify that the MS, when returning to the old channel after handover or Assignment failure and correctly establishing the link, will remain in the call active state. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.3.2.4 Method of test | Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in CC-state "active".
Foreseen final state of the MS
CC-state "active".
Maximum duration of test
30 s.
Test procedure
The SS initiates a call to the Mobile Station, using an arbitrari... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.4 In-call functions / MS terminated in-call modification | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.4.1 In-call functions / MS terminated in-call modification / modify when new mode is not supported | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.4.1.1 Definition | This is to test a special case of a in-call modification procedure, in which the new mode is not supported (and consequently not one of those negotiated and agreed during the establishment phase of the call). This test is applicable for any equipment supporting at least one circuit switched basic service. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.4.1.2 Conformance requirement | 1) In the case that the MS supports the network originated in-call modification procedure, the MS after having received a MODIFY message with a new mode which is not the actual one and cannot be supported by the MS shall reject it by sending a MODIFY REJECT message or a STATUS message.
2) In the case that the MS does n... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.4.1.3 Test purpose | 1) To verify that an MS supporting the network originated in-call modification procedure, after having received a MODIFY message with a new mode which is not the actual one and cannot be supported by the MS, rejects it by sending a MODIFY REJECT.
2) To verify that an MS not supporting the network originated in-call mod... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.4.1.4 Method of test | Specific PICS statements
- the MS supports the network originated in-call modification procedure (p = Yes/No) (TSPC_AddInfo_InCallMod)
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in CC-state "active".
Foreseen final state of the MS
CC-state "active".
Max... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5 In-call functions / MS originated in-call modification | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.1 In-call functions / MS originated in-call modification / a successful case of modifying | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.1.1 Definition | This test is to test a successful case of in-call modification, which is triggered by the calling tone identification (CNG) received by the MS. This test is applicable for any equipment supporting any dual mode bearer capability service (BS61 - Alternate Speech/Data, BS81 - Speech followed by Data, Teleservice 61 - Alt... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.1.2 Conformance requirement | 1) The procedure shall be initiated by the MS in the "active" state of the call. It shall send a MODIFY message including the new mode to be changed to; and enter the "mobile originating modify" state. The new mode given in the MODIFY message shall be one of those already negotiated and agreed during the establishment ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.1.3 Test purpose | 1) To verify that the procedure is initiated by the MS in the "active" state of the call. It sends a MODIFY message including the new mode to be changed to; and enters the "mobile originating modify" state. The new mode given in the MODIFY message is one of those already negotiated and agreed during the establishment p... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.1.4 Method of test | Specific PICS statements
-
PIXIT statements
- a way to activate a dual mode call
- a way to activate in-call modificationInitial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
CC-state "active".
Maxi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.2 In-call functions / MS originated in-call modification / modify rejected | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.2.1 Definition | This is to test a special case of a in-call modification procedure, in which the in-call modification is rejected. This test is applicable for any equipment supporting any dual mode bearer capability service (BS61 - Alternate Speech/Data, BS81 - Speech followed by Data, Teleservice 61 - Alternate Speech/Group 3 fax). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.2.2 Conformance requirement | 1) Upon receipt of the MODIFY REJECT message with the old bearer capability the MS shall: resume sending Bm-channel information according to the present call mode; resume interpreting received Bm-channel information according to the present call mode; and enter the "active" state.
References
3GPP TS 04.08 / 3GPP TS 24.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.2.3 Test purpose | To verify that upon receipt of the MODIFY REJECT message with the old bearer capability the MS resumes sending Bm-channel information according to the present call mode; resumes interpreting received Bm-channel information according to the present call mode; and enters the "active" state. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.2.4 Method of test | Specific PICS statements
-
PIXIT statements
- a way to activate a dual mode call
- a way to activate in-call modification
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
CC-state "active".
Max... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.3 In-call functions / MS originated in-call modification / an abnormal case of acceptance | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.3.1 Definition | This is to test a special case of a in-call modification procedure, in which the in-call modification is accepted incorrectly. This test is applicable for any equipment supporting any dual mode bearer capability service (BS61 - Alternate Speech/Data, BS81 - Speech followed by Data, Teleservice 61 - Alternate Speech/Gro... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.3.2 Conformance requirement | 1) Upon receipt of the MODIFY COMPLETE message indicating a call mode which does not correspond to the requested one the MS shall discard it and take no action.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.4.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.3.3 Test purpose | To verify that upon receipt of the MODIFY COMPLETE message indicating a call mode which does not correspond to the requested one the MS discards it and takes no action. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.3.4 Method of test | Specific PICS statements
-
PIXIT statements
- a way to activate a dual mode call
- a way to activate in-call modification
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
CC-state U26 "Mobile O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.4 In-call functions / MS originated in-call modification / an abnormal case of rejection | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.4.1 Definition | This is to test a special case of a in-call modification procedure, in which the in-call modification is rejected incorrectly. This test is applicable for any equipment supporting any dual mode bearer capability service (BS61 - Alternate Speech/Data, BS81 - Speech followed by Data, Teleservice 61 - Alternate Speech/Gro... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.4.2 Conformance requirement | 1) Upon receipt of the MODIFY REJECT message indicating a call mode which does not correspond to the actual one the MS shall discard it and take no action.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.4.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.4.3 Test purpose | To verify that upon receipt of the MODIFY REJECT message indicating a call mode which does not correspond to the actual one the MS discards it and takes no action. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.4.4 Method of test | Specific PICS statements
-
PIXIT statements
- a way to activate a dual mode call
- a way to activate in-call modification
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
CC-state U26 "Mobile O... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.5 In-call functions / MS originated in-call modification / time-out of timer T323 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.5.1 Definition | This is to test a special case of a in-call modification procedure, in which timer T323 expires in state U26, mobile originating modify. This test is applicable for any equipment supporting any dual mode bearer capability service (BS61 - Alternate Speech/Data, BS81 - Speech followed by Data, Teleservice 61 - Alternate ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.5.2 Conformance requirement | 1) Upon expiration of T323 the MS shall initiate the procedures for call clearing with cause #102 "recovery on timer expiry".
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.4.3.4.3. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.5.3 Test purpose | To verify that upon expiration of T323 (accuracy ± 10 %) the MS shall initiate the procedures for call clearing with cause #102 "recovery on timer expiry". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.5.4 Method of test | Specific PICS statements
-
PIXIT statements
- a way to activate a dual mode call
- a way to activate in-call modification
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
CC-state U11 "disconne... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.6 In-call functions / MS originated in-call modification / a successful channel change in state mobile originating modify | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.6.1 Definition | This is to test a special case of a in-call modification procedure, in which a change of a physical channel occurs in state U26, mobile originating modify. This test is applicable for any equipment supporting any dual mode bearer capability service (BS61 - Alternate Speech/Data, BS81 - Speech followed by Data, Teleserv... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.6.2 Conformance requirement | 1) A CC-entity of the MS in CC-state U26, "Mobile Originating Modify", after successful completion of a channel assignment procedure or channel mode modify procedure shall remain in the call state U26.
2) Upon receipt of the MODIFY COMPLETE message the MS shall start sending channel information according to the new cal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.6.3 Test purpose | 1) To verify that a CC-entity of the MS in CC-state U26, "Mobile Originating Modify", after successful completion of a channel assignment procedure remains in the call state U26.
2) To verify that upon receipt of the MODIFY COMPLETE message the MS starts sending channel information according to the new call mode and en... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.6.4 Method of test | Specific PICS statements
-
PIXIT statements
- a way to activate a dual mode call
- a way to activate in-call modification
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
CC-state U10, active.
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.7 In-call functions / MS originated in-call modification / an unsuccessful channel change in state mobile originating modify | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.7.1 Definition | This is to test a special case of a in-call modification procedure, in which an unsuccessful change of a physical channel occurs in state U26, mobile originating modify. This test is applicable for any equipment supporting any dual mode bearer capability service (BS61 - Alternate Speech/Data, BS81 - Speech followed by ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.7.2 Conformance requirement | 1) A CC-entity of the MS in CC-state U26, "Mobile Originating Modify", when returning to the old channel after handover failure and having established the link, shall remain in the call state U26.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.4.3.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.7.3 Test purpose | To verify that a CC-entity of the MS in CC-state U26, "Mobile Originating Modify", when returning to the old channel after handover failure and having established the link, remains in the call state U26. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.7.4 Method of test | Specific PICS statements
-
PIXIT statements
- a way to activate a dual mode call
- a way to activate in-call modification
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
CC-state U26, mobile o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.8 In-call functions / MS originated in-call modification / unknown message received | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.8.1 Definition | This is to test a special case of a in-call modification procedure, in which an unknown message is received in state U26, mobile originating modify. This test is applicable for any equipment supporting any dual mode bearer capability service (BS61 - Alternate Speech/Data, BS81 - Speech followed by Data, Teleservice 61 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.8.2 Conformance requirement | A CC entity of a MS in CC-state U26, "Mobile Originating Modify", having received an unknown message from its peer entity shall return a STATUS message.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 8.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.8.3 Test purpose | To verify that a CC entity of a MS in CC-state U26, "Mobile Originating Modify", having received an unknown message from its peer entity returns a STATUS message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.8.4 Method of test | Specific PICS statements
-
PIXIT statements
- a way to activate a dual mode call
- a way to activate in-call modification
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
CC-state U26, mobile o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.9 In-call functions / MS originated in-call modification / a release complete received | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.9.1 Definition | The call control entity of the MS being in the state, U26, the call is cleared by a RELEASE COMPLETE message sent by the SS. This test is applicable for any equipment supporting any dual mode bearer capability service (BS61 - Alternate Speech / Data, BS81 - Speech followed by Data, Teleservice 61 - Alternate Speech / G... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.9.2 Conformance requirement | 1) A CC entity of the MS in CC-state U26, "mobile originating modify", upon receipt of a RELEASE COMPLETE message with valid cause value, shall enter CC state U0, "Null".
2) On returning to idle mode, the CC entities relating to the seven mobile originating transaction identifiers shall be in state U0, "Null".
Referenc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.9.3 Test purpose | 1) To verify that a CC entity of the MS in CC-state U26, "mobile originating modify", upon receipt of a RELEASE COMPLETE message with valid cause value, enters CC state U0, "Null".
2) To verify that on returning to idle mode, the CC entities relating to the seven mobile originating transaction identifiers are in state ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.9.4 Method of test | Specific PICS statements
-
PIXIT statements
- a way to activate a dual mode call
- a way to activate in-call modification
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
The MS is in MM-state ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.1.4.5.10 In-call functions/MS originated in-call modification/contents of some of the messages | The following messages are used for testing in-call modification procedures, test cases 26.8.1.4.5.*, as default messages for those ones defined below. If any other values are defined in the expected sequence of the actual test cases, those values take precedence over the ones defined hereafter.
SETUP (MS to SS)
Inform... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2 Call Re-establishment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.1 Call Re-establishment/call present, re-establishment allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.1.1 Definition | This is to test a successful case of a call re-establishment procedure. This test is applicable for any equipment supporting at least one bearer capability. If the MS does not perform call re-establishment procedure correctly, the network will waste resources. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.1.2 Conformance requirement | 1) If the call is in the "active" state or "mobile originating modify" state, the indication from MM that re-establishment is possible shall cause call control to request re-establishment from the MM-connection, suspend any further message to be sent and await the completion of the re-establishment procedure.
2) When t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.1.3 Test purpose | The purpose of this test is to verify that the MS can correctly perform a call re-establishment procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.1.4 Method of test | Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
The SS simulates cells A and B. The LAC of cell A is different from the LAC of cell B. The PLMN identities of cell A and B are equal.
The call re-establishment parameter concerning cell A is set to an arbitrary value.
Cell B is not barre... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.2 Call Re-establishment/call present, re-establishment not allowed | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.2.1 Definition | This is to test a special case of a call re-establishment, in which it is not allowed for a MS to attempt re-establishment of a call. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.2.2 Conformance requirement | When a lower layer failure occurs while an MM-connection is active, if a cell allowing call re-establishment is not available, the MS shall release the MM-connection and shall not attempt call re-establishment.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 4.5.1.6 and 5.5.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.2.3 Test purpose | The purpose of this test is to verify that the MS does not attempt call re-establishment when it is not allowed to take place because of the unavailability of a cell allowing call re-establishment. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.2.4 Method of test | Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
The SS simulates cell A.
Cell A is not barred, the NCC of cell A is indicated as permitted in the PLMN permitted information element of SYSTEM INFORMATION TYPE 2 and 6 messages. The RE field of the RACH control parameters information ele... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.3 Call Re-establishment/call under establishment, transmission stopped | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.3.1 Definition | This is to test a special case of a call re-establishment, in which it is not allowed for a MS to attempt re-establishment of a call, since the call has not been established yet. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.3.2 Conformance requirement | When a lower layer failure occurs while an MM-connection is active, if the state of the call control entity is not "active", the MS shall release the MM-connection and shall not attempt call re-establishment.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 4.5.1.6 and 5.5.4.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.3.3 Test purpose | The purpose of this test is to verify that the MS does not attempt call re-establishment when it is not allowed to take place because of the call control state. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.2.3.4 Method of test | Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
The SS simulates cell A.
Cell A is not barred, the RACH control parameters information element sent in SYSTEM INFORMATION TYPE 1 to 4 messages of cell A specifies "call reestablishment allowed in the cell", the NCC of cell A is indicated... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.3 User to user signalling | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.3.1 Definition | The "user to user" information element is used to convey information between the mobile user and a remote ISDN user. This test is therefore applicable for any equipment supporting at least one mobile terminating circuit switched basic service.
NOTE: There is no test for an MS originating call including a "user-user" in... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.3.2 Conformance requirement | The inclusion of the "user-user" information element in downlink call control messages shall cause no adverse effects on the operation of the MS.
References
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.2, 9.3.7, 9.3.23.1 and 10.5.4.25. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.3.3 Purpose of the test | The purpose of this test is to verify that inclusion of the "user-user" information element in either of the down link messages, SETUP or DISCONNECT causes no adverse effects on the operation of the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.3.4 Method of test | Specific PICS statements
-
PIXIT statements
-
Initial conditions.
System Simulator:
The SS simulates 1 cell, with default parameters.
Mobile Station:
The MS is in MM-state "idle updated", with a valid TMSI and CKSN.
Foreseen final state of the MS
The MS is in MM-state "idle updated", with a valid TMSI and CKSN.
Maximum... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.8.4 Default contents of message | ALERTING (mobile station to network direction)
No default requirements defined for this message.
ALERTING (network to mobile station direction)
Information element
Value/remark
Facility
Omitted
Progress indicator
Omitted
User-user
Omitted
ASSIGNMENT COMMAND
Information element
Value/remark
Description of the first chan... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.