hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9 Structured procedures | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.1 Structured procedures / general | The purpose of these tests is to verify that the MS performs certain elementary procedures of the RR, MM, and CC protocol correctly within a structured procedure. The term "structured procedure" is defined in 3GPP TS 04.08 / 3GPP TS 23.108, clause 7, where also examples of structured procedures are given.
The reason fo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.2 Structured procedures / MS originated call / early assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.2.1 Conformance requirements | 1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice that is supported by the MS, shall start to initia... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.2.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS as declared in a PICS/PIXIT statement, displays the dialled number in the way described in a PICS/PIXIT statement.
2) To verify that the MS in MM state "idle, up... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.2.3 Method of test | (* this affects the 'correct' contents of the SETUP message *)
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1)... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.3 Structured procedures / MS originated call / late assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.3.1 Conformance requirement | 1) An MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS , shall start to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.
2) Upon receipt of the A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.3.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message.
2) To ver... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.3.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1)
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.4 Structured procedures / MS terminated call / early assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.4.1 Conformance requirements | 1) The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does not refuse the call.
2, 3) Upon receipt of the ASSIGNMENT COMMAND message the MS continues a mobile terminating call establishment with early establishment of the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.4.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, after being paged by the network on the correct paging subchannel, after initiating the immediate assignment procedure by sending the CHANNEL REQUEST message, after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.4.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_Add... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.5 Structured procedures / MS terminated call / late assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.5.1 Conformance requirement | TP1, TP2: The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does not refuse the call. The MS on acceptance of the call sends a CONNECT, otherwise user alerting is initiated.
TP3: The MS indicates acceptance of a call by s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.5.2 Test purpose | 1) To verify that the MS in "Idle, Updated" state with a TMSI assigned, after being paged by the network on the correct paging subchannel, after initiating the immediate assignment procedure by sending the CHANNEL REQUEST message, after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after having establ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.5.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_Add... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6 Structured procedures / emergency call | Emergency call establishment can be initiated by an MS whether location updating has been successful or not and whether a SIM is inserted into the MS or not; but only if the MS is equipped for speech.
If the procedures tested in this subclause are not correctly implemented in the MS, establishment, maintenance and clea... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1 Structured procedures / emergency call / idle updated | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1.1 Structured procedures / emergency call / idle updated / preferred channel rate | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1.1.1 Conformance requirement | 1) For R97/98 MS: The MS in the "idle, updated" state, as after a successful location update, after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1.1.2 Test purpose | 1) To verify that an R97/R98 MS supporting speech in the MM state "idle, updated", when made to call the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico), sends a CHANNE... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Use of R99 Emergency numbers (TSPC_R99_Emerg)
PIXIT statemen... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1.2 Structured procedures / emergency call / idle updated, non-preferred channel rate | This test is identical to the test in subclause 26.9.6.1.1 except that in step 14 the assigned TCH has the non-preferred rate. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1.3 Structured procedures / emergency call / idle updated / EAB active | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1.3.1 Conformance requirement | The preliminary access barring check shall indicate network access is barred if all of the following conditions are satisfied:
• the establishment cause for the request received from the MM sublayer is not "emergency call".
• the SYSTEM INFORMATION TYPE 21 message is broadcast in the cell and includes EAB information;
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1.3.2 Test purpose | To verify that the MS, configured for Extended Access class Barring can initiate an emergency call when EAB is being broadcast
To verify that the Low Access Priority indicator is set in the Service Request message |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.1.3.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
The SYSTEM INFORMATION TYPE 3 message indicates that the SYSTEM INFORMATION TYPE 21 is sent on the BCCH by setting the SYSTEM INFORMATION 21 Indicator in the SI3 Rest Octet IE.
The SYSTEM INFORMATION TYPE 21 is sent on the BCCH. The SI 21 Rest Octets info... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.2 Structured procedures / emergency call / idle, no IMSI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.2.1 Structured procedures / emergency call / idle, no IMSI / accept case | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.2.1.1 Conformance requirement | 1) The MS in the "idle, updated" state, as after a successful location update, after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.2.1.2 Test purpose | 1) To verify that the MS in the "idle, no IMSI" state (no SIM inserted) when made to call the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico), sends a CHANNEL REQUEST m... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.2.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Specific PICS statements:
- .
PIXIT statements:
- .
Foreseen Final State of the MS
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Test procedure
The MS is made to initiate an... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.2.2 Structured procedures / emergency call / idle, no IMSI / reject case | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.2.2.1 Conformance requirement | 1) The MS in the "idle, no IMSI" state (no SIM inserted), after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered, shall send a CHANNEL REQUEST messa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.2.2.2 Test purpose | 1) To verify that the MS in the "idle, no IMSI" state (no SIM inserted) when made to call the number 112, (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) sends a CHANNEL REQUEST m... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.6.2.2.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Specific PICS statements:
- .
PIXIT statements:
- .
Foreseen Final State of the MS
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Test procedure
The MS is made to initiate an... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.7 Directed Retry / Mobile Originated Call | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.7.1 Conformance requirements | The MS shall correctly apply the Directed Retry procedure from SDCCH/8 (with frequency hopping) or SDCCH/4 to TCH/F or TCH/H with or without frequency hopping in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "mobile originating call proceeding" state shall, up... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.7.2 Test purpose | To test that, when the MS is ordered to perform a non-synchronized handover after the CALL PROCEED message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advanc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.7.3 Method of test | Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below.
Cell Allocation = (See the table below.
PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
PLMN_PERM = 00001010.
Cell B has:
BCCH ARFCN = See the table below... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.8 Directed Retry / Mobile Terminated Call | This test is applicable to all MS which support at least one MT circuit switched basic service. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.8.1 Conformance requirements | The MS shall correctly apply the Directed Retry procedure from SDCCH/8 (with frequency hopping) or SDCCH/4 to TCH/F or TCH/H with or without frequency hopping in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "call delivered" state shall, if the MS supports imm... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.8.2 Test purpose | To test that when the MS is ordered to perform a non-synchronized handover after the CALL CONFIRM message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.8.3 Method of test | Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below.
Cell Allocation = See the table below.
PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
PLMN_PERM = 00001010.
Cell B has:
BCCH ARFCN = See the table belo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.9.9 Default contents of messages | ALERTING (mobile station to network direction)
Information element
Value/remark
Facility
Not checked
User-user
Not checked
SS version
Not checked
ALERTING (network to mobile station direction)
Information element
Value/remark
Facility
Omitted
Progress indicator
Omitted
User-user
Omitted
ASSIGNMENT COMMAND
Information e... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.1 E-GSM or R-GSM or ER-GSM signalling / general considerations | Subclause 26.10 only applies to E-GSM, R-GSM and ER-GSM mobile stations. The details of frequencies used in different test cases are listed below.
Table 26.1: Frequencies used for E-GSM or R-GSM or ER-GSM signalling tests
Test Case
Frequencies used in the test case
E-GSM testing
R-GSM or ER-GSM testing
26.10.2.1
neighb... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2 E-GSM or R-GSM or ER-GSM signalling / RR | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.1 E-GSM or R-GSM or ER-GSM signalling / RR / Measurement | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.1.1 Conformance requirements | The MS shall continuously send MEASUREMENT REPORT messages on every SACCH blocks and the measurement valid indication shall be set to valid (0) within the second block at the latest. After 20 s the values in the MEASUREMENT REPORT message shall contain measurement results for the 6 th strongest cells belonging to the s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.1.2 Test purpose | To test that, when the SS gives information about neighbouring cells indicated either in SI5 and SI5bis messages or in SI5 and SI5ter messages, the MS reports appropriate results. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.1.3 Method of test | Initial Conditions
System Simulator:
8 cells with the following settings:
E-GSM:
Transmitter
Level
NCC
BCC
ARFCN
Cell Identity
Serving, S1
‑60
1
3
002
0001H
Neighbour, N1
‑85
1
5
990
0002H
Neighbour, N2
‑80
1
7
1005
0003H
Neighbour, N3
‑75
1
1
000
0004H
Neighbour, N4
‑55
1
3
026
0005H
Neighbour, N5
‑50
1
5
1020
0006H
N... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.2 E-GSM or R-GSM or ER-GSM signalling / RR / Immediate assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.2.1 Conformance requirement | Following a PAGING REQUEST message, the MS shall correctly set up an RR connection on a supported channel described in the IMMEDIATE ASSIGNMENT message, using some E-GSM or R-GSM or ER-GSM frequency.
Reference(s)
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.2.2 Test purpose | To verify that the MS can correctly set up a dedicated control channel when E-GSM or R-GSM or ER-GSM frequencies are used.
This tested for a SDCCH/8. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.2.3 Method of test | Initial Conditions
System Simulator:
1 cell.
E-GSM:
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
SYSTEM INFORMATION type 1 message contains the following frequencies in the Cell Channel Description IE: 0, 30, 40, 66, 80, 1 005, 1 010, 1 015 (use range 1 024 to encode).
BCCH car... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.3 E-GSM or R-GSM or ER-GSM signalling / RR / channel assignment procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.3.1 Conformance requirements | 1. Upon receipt of the ASSIGNMENT COMMAND message, the mobile station initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, thei... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.3.2 Test purpose | 1. To verify that upon receipt of an ASSIGNMENT COMMAND, the MS switches to the channel defined in the ASSIGNMENT COMMAND, establishes the link and sends an ASSIGNMENT COMPLETE message.
2. To verify that an MS, having received an ASSIGNMENT COMMAND, is able in case of frequency hopping to decode the mobile allocation a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.3.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in the "idle, updated" state with a TMSI allocated.
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
-
Foreseen Final State o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.4 E-GSM or R-GSM or ER-GSM signalling / RR / Handover | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.4.1 E-GSM or R-GSM or ER-GSM signalling / RR / Handover / Successful handover | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.4.1.1 Conformance requirements | The MS shall correctly apply the handover procedure from a channel without frequency hopping in the primary band to a channel with frequency hopping using P-GSM and E-GSM or P-GSM and R-GSM or ER-GSM frequencies whatever the coding used for the frequency hopping description.
References
3GPP TS 04.08 / 3GPP TS 44.018, s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.4.1.2 Test purpose | To check that the MS correctly performs a non-synchronized handover, from a non hopping primary band SDCCH to a hopping TCH or SDCCH using E-GSM or R-GSM or ER-GSM frequencies, whatever the coding used for the hopping sequence description and that it activates the new channel correctly.
This is tested in the following ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.4.1.3 Method of test | Initial Conditions
System Simulator:
E-GSM:
2 cells A and B with same LAI, default parameters;
except for Cell A: the broadcasted Cell Channel Description in SYSTEM INFORMATION type 1 message contains the following frequencies: 20, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114 (encoded using Bit Map 0 format);
The broad... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.4.2 E-GSM or R-GSM or ER-GSM signalling / RR / Handover / layer 1 failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.4.2.1 Conformance requirements | During a handover from a channel in the E-GSM or R-GSM or ER-GSM band to a channel in the P-GSM band, or the contrary, the MS shall correctly return to the old channel in the case of an handover failure caused by a layer 1 failure on the target cell.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.4.2.2 Test purpose | To check that the MS correctly returns to the old channel in the case of a handover failure caused by a layer 1 failure on the target cell, even if the origin is in the P-GSM band and the target in the E-GSM or R-GSM or ER-GSM band. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.4.2.3 Method of test | Initial Conditions
System Simulator:
E-GSM:
2 cells with same LAI, default parameters.
Cell A: The broadcasted BCCH frequency list for Cell A in SYSTEM INFORMATION type 2 and 5 contains the following frequencies: 10, 20, 40, 80, 90, 100, 110 and 120 (encoded in Bit Map 0 format).
The BCCH carrier number of Cell B is 40... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.5 E-GSM or R-GSM or ER-GSM signalling / RR / Frequency Redefinition | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.5.1 Conformance requirements | 1) To verify that the MS, after receiving a FREQUENCY REDEFINITION message, correctly starts using the new frequencies, and hopping sequence when some E-GSM or R-GSM or ER-GSM frequencies are used.
2) The last received Cell Channel Description information element is used to decode the Mobile Allocation IE received on t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.5.2 Test purpose | 1) To verify that the MS, after receiving a FREQUENCY REDEFINITION message, starts using the new frequencies and hopping sequence when some E-GSM or R-GSM or ER-GSM frequencies are used.
2) To check that the last received Cell Channel Description information element is used to decode the Mobile Allocation IE received i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.2.5.3 Method of test | Initial conditions
System Simulator:
1 cell; default parameters.
Mobile Station:
The MS is in "idle, updated" state with TMSI allocated.
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
-
Foreseen final state of the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3 E-GSM or R-GSM or ER-GSM signalling / Structured procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3.1 E-GSM or R-GSM or ER-GSM signalling / Structured procedure / Mobile originated call | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3.1.1 Conformance requirement | 1) An MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS , shall start to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.
2) Upon receipt of the A... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3.1.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message.
2) To ver... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3.1.3 Method of test | Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
- Way to indicate mobile originated alerting.
-. Way to display the called number
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3.2 E-GSM or R-GSM or ER-GSM signalling / Structured procedures / emergency call | Emergency call establishment can be initiated by an MS whether location updating has been successful or not and whether a SIM is inserted into the MS or not; but only if the MS is equipped for speech.
This subclause is only applicable to an MS supporting speech. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3.2.1 Conformance requirement | 1) The MS in the "idle, updated" state, as after a successful location update, after the number 112 has been entered by user, shall send a CHANNEL REQUEST message with correct establishment cause ("emergency call").
2) After assignment of a dedicated channel the first layer message sent by the MS on the assigned dedica... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3.2.2 Test purpose | 1) To verify that the MS in the "idle, no IMSI" state (no SIM inserted) when made to call the number 112, sends a CHANNEL REQUEST message with establishment cause "emergency call".
2) To verify that after assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel is a CM ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3.2.3 Method of test | Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band )
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
-
Initial Conditions
System Simulator:
1 cell, default parameters except:
See Table 26.1
Mobile Station:
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Fores... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.3.3 Default contents of messages | Same as in subclause 26.9.7 except for the following.
ASSIGNMENT COMMAND
E-GSM:
Information element
Value/remark
Description of the first channel
describes non-hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
ARFCN = 990
Power Command
-
Chosen arbitrarily but within the range supported by the MS.
Frequency list... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.10.4 E-GSM or R-GSM or ER-GSM signalling / Default message contents | Default SYSTEM INFORMATION:
NOTE: SYSTEM INFORMATION 7, and SYSTEM INFORMATION 8 messages are not used.
SYSTEM INFORMATION type 1 message
Information elements
Value/Remark
Cell Channel Description
For Cell A
- Format identifier
Bit Map 0
- Cell Allocation ARFCN
Channel Numbers 20, 30, 50 and 70.
For Cell B
- Format ide... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11 Multiband signalling | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.1 General considerations | This subclause applies only to Multiband mobile stations, as defined in 3GPP TS 02.06 subclause 3.2.1.
Conformance requirements of clause 26 fully apply to any Multiband MS in the whole supported band(s) of operation of the mobile station.
A Multiband mobile station has the functionality to perform handover, channel as... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2 Multiband signalling / RR | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.1 Multiband signalling / RR / Immediate assignment procedure | To inform the multiband network of the MSs additional frequency and power capability, the multiband MS has to send a CLASSMARK CHANGE as soon as possible in a connection establishment. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.1.1 Conformance requirement | Following a PAGING REQUEST message, the MS shall correctly set up an RR connection on a supported channel described in the IMMEDIATE ASSIGNMENT message. On the MS side, the procedure is terminated when the establishment of the main signalling link is confirmed. When the ES bit is set to 1 in the Classmark 1 or the Clas... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.1.2 Test purpose | To verify that the MS can correctly set up a dedicated control channel and that a multi band MS is able to perform early sending of CLASSMARK CHANGE.
To verify the performance requirement on early sending of the CLASSMARK CHANGE message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.1.3 Method of test | Initial Conditions
System Simulator:
For 450/900 MS:
1 cell.
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
BCCH carrier number 263.
For 480/900 MS:
1 cell.
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
BCCH carrier number 310.
For 450/1 8... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.2 Multiband signalling / RR / Handover | This subclause applies to any multiband mobile stations.
The purpose of this extra section is to test the handover where the target cell uses frequencies outside the frequency band of the serving cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.2.1 Multiband signalling / RR / Handover / successful / active call / non-synchronized | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.2.1.1 Conformance requirements | The MS shall correctly apply the handover procedure in the non-synchronized case when a call is in progress and when handover is performed from a TCH/F without frequency hopping in one band towards a TCH/F without frequency hopping in another band.
When the MS releases a TCH or SDCCH and returns to idle mode, it shall,... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.2.1.2 Test purpose | To test that when the MS is ordered to make a non-synchronized handover it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly handles the Timing Advance IE in the PHYSICAL INFORMATION message. To tes... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.2.1.3 Method of test | Initial Conditions
For execution counter M =1, 2
System Simulator:
For 450/900 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 263
Cell Allocation = (259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291)
Cell B has:
BCCH ARFCN = 20
Cell Allocation =... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.2.2 Multiband signalling / RR / Handover / layer 1 failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.2.2.1 Conformance requirements | During a handover from a channel in the lower band to a channel in the upper band, or the contrary, the MS shall correctly return to the old channel in the case of an handover failure caused by a layer 1 failure on the target cell.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.11.2.2.2.2 Test purpose | To check that the MS correctly returns to the old channel in the case of an handover failure caused by a layer 1 failure on the target cell, if the origin is in the lower band and the target is in the upper band or the contrary. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.