hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.3.3 Method of test | Initial Conditions
System Simulator:
- 2 cells, A and B, with same LAI, default parameters, except:
- Early classmark sending enabled in SI3 rest octets- The BCCH of cell A is sent k bit periods before the BCCH of cell B. The timing advance in cell A sent to the MS is y bit periods. k and y are selected such that 0 < (... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.4 Multislot signalling / RR / Handover / successful / call under establishment / finely synchronized / relocation of channels | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.4.1 Conformance requirements | 1) The MS shall correctly apply the handover procedure from hopping, multislot configuration, finely synchronized case to hopping, multislot configuration, synchronized case during call establishment.
2) The MS shall not change number of channels in multislot configuration but the place of each channel is changed.
3) I... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.4.2 Test purpose | 1) To test that when the MS is ordered to make a finely synchronized handover to a synchronized cell, it sends 4 access bursts on the main DCCH (before completion, additional access bursts may also be sent on the SACCH) and then activates the channel correctly, taking into account power command, new order of channels i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.4.3 Method of test | Initial Conditions
System Simulator:
- 2 cells, A and B, with same LAI, default parameters, except:
- Early classmark sending enabled in SI3 rest octets.
- The BCCH of cell A is sent k bit periods before the BCCH of cell B. The timing advance in cell A sent to the MS is y bit periods. k and y are selected such that 0 <... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.5 Multislot signalling / RR /Handover / successful / call under establishment / pre-synchronized / resource upgrading | If an MS does not implement the pre-synchronized handover procedure correctly then calls may fail.
If an MS does not report the observed time difference between cells correctly then pseudo synchronized handovers might not be possible for any MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.5.1 Conformance requirements | 1) If during call establishment a Layer 3 MM or CC message just sent by the MS is not Layer 2 acknowledged before the channel change caused by the HANDOVER COMMAND message, the MS shall send the Layer 3 message to the new cell, using the same value in the N(SD) field, after the handover procedure.
2) When the Timing Ad... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.5.2 Test purpose | 1) To verify that when the MS is ordered to make a pre-synchronized handover from hopping multislot configuration to non-hopping multislot configuration, it sends 4 access bursts on the main DCCH (before completion, additional access bursts may also be sent on the SACCH) and then activates the channel correctly and cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.5.3 Method of test | Initial Conditions
System Simulator:
- 2 cells, A and B, with same LAI, default parameters, except:
- Early classmark sending enabled in SI3 rest octets.
- The BCCH of cell A is sent k bit periods before the BCCH of cell B.
Mobile Station:
- The MS is in the "idle, updated" state, with a TMSI allocated and camped on ce... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.4 Multislot signalling / RR / Test of the channel mode modify procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.4.1 Conformance requirements | 1) When the MS has received the CHANNEL MODE MODIFY message, the mobile station changes the mode for the indicated channel and then replies by a CHANNEL MODE MODIFY ACKNOWLEDGE message indicating the new channel mode.
2) If the mobile station does not support the indicated mode, it shall retain the old mode and return ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.4.2 Test purpose | 1) To verify that the MS, in an RR connected state, acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGEMENT message specifying and switching to the correct mode for the channels in a multislot configuration:
- the new mode if that mode is supported;
- the old mode if the new mode is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.4.3 Method of test | Initial Conditions
System Simulator:
- 1 cells, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Mobile Station:
- The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
• Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
supported radio interface rates: 12k... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.5 Multislot signalling / RR / Early classmark sending | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.5.1 Conformance requirement | 1) MS uses Controlled Early Classmark Sending procedure when indicated in SYSTEM INFORMATION TYPE 3 (ES ind bit in SI 3 Rest Octets).
1.1) If Controlled Early Classmark Sending is not allowed by network the MS does not send a CLASSMARK CHANGE message.
1.2) If Controlled Early Classmark Sending is allowed by network the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.5.2 Test purpose | 1) To verify that the MS sends its multislot class in Mobile Station Classmark 3 using Controlled Early Classmark Sending procedure if allowed by network.
2) To verify that the MS does not perform Early Classmark Sending if it is not allowed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.5.3 Method of test | Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
MS is in MM-state "idle, updated... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.6 Default contents of layer 3 messages for RR tests | 26.13.1.6.1 Default contents of GSM 900 layer 3 messages for RR tests
This subclause contains the default values of GSM 900 L3 messages, which unless indicated otherwise in subclause 26.13 shall be transmitted by the system simulator and which are required to be received from the GSM 900 MS under test.
The necessary L3... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2 Multislot signalling / CC | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1 Multislot signalling / CC / In-call functions | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1 Multislot signalling / CC / In-call functions / User initiated service level upgrade / successful | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1.1 Definition | Multislot connection is established. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is successfully performed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1.2 Conformance requirements | 1) MS shall send MODIFY message to SS indicating that User initiated service level upgrade is initiated.
2) MS enters CC state 'Mobile originating modify (U26)' after sending MODIFY.
3) MS enters CC state 'Active (U10)' when MODIFY COMPLETE is received.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.0... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1.3 Test purpose | 1) To verify that the procedure is initiated by the MS in the "active" state of a multislot connection. It sends a MODIFY message including the wanted value of the "maximum number of traffic channels" and/or the "wanted air interface" parameters; and enters the "mobile originating modify" state. Other parameters of the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1.4 Method of test | Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection.
System simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.2 Multislot signalling / CC / In-call functions / User initiated service level downgrade / successful | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 25.13.2.1.2.1 Definition | Multislot connection is established. Multislot configuration has the maximum number of timeslots supported by the MS. User initiated service level downgrade is successfully performed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.2.2 Conformance requirements | 1) MS shall send MODIFY message to SS indicating that User initiated service level downgrade is initiated.
2) MS enters CC state 'Mobile originating modify (U26)' after sending MODIFY.
3) MS enters CC state 'Active (U10)' when MODIFY COMPLETE is received.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.2.3 Test purpose | 1) To verify that the procedure is initiated by the MS in the "active" state of a multislot connection. It sends a MODIFY message including the wanted value of the "maximum number of traffic channels" and/or the "wanted air interface" parameters; and enters the "mobile originating modify" state. Other parameters of the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.2.4 Method of test | Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection. Multislot configuration has maximum number of timeslots supported by the MS.
System simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Specific PICS statements:
- Mult... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3 Multislot signalling / CC / In-call functions / User initiated service level upgrade / Time-out of timer T323 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3.1 Definition | Multislot connection is established. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is requested. Timer T323 expires. Call is cleared. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3.2 Conformance requirements | 1) MS shall send MODIFY message to SS indicating that User initiated service level upgrade is initiated.
2) After timer T323 has expired MS starts call clearing by sending DISCONNECT message.
3) After receipt of RELEASE message the MS sends RELEASE COMPLETE message and goes to idle updated state.
References
Conformance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3.3 Test purpose | 1) To verify that upon expiration of T323 (accuracy ± 10%) the MS shall initiate the procedures for call clearing with cause #102 "recovery on timer expiry". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3.4 Method of test | Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection.
System simulator:
- 1 cell, default parameters
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final state of the MS
"Idle, updated", with TMSI allocated.
Test pro... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4 Multislot signalling / CC / In-call functions / User initiated service level upgrade / modify reject | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4.1 Definition | Multislot connection is established. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is requested. SS responds to upgrade request by rejecting it. MS enters the active multislot connection state. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4.2 Conformance requirements | 1) MS shall send MODIFY message to SS indicating that User initiated service level upgrade is initiated.
2) MS enters CC state 'Mobile originating modify (U26)' after sending MODIFY.
3) MS enters CC state 'Active (U10)' when MODIFY REJECT is received.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4.3 Test purpose | 1) To verify that upon receipt of the MODIFY REJECT message with the bearer capability negotiated at the call setup, the MS is continuously sending user information according to current call mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4.4 Method of test | Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection.
System simulator:
- 1 cell, default parameters
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final state of the MS
MS is in the active state of a service using a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.5 Multislot signalling / CC / In call functions / contents of some of the messages | The following messages are used for testing in-call modification procedures, test cases 26.13.2.1.*, as default messages for those ones defined below. If any other values are defined in the expected sequence of the actual test cases, those values take precedence over the ones defined hereafter.
SETUP (MS to SS)
Informa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3 Multislot signalling / Structured procedures | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.1 Multislot signalling / Structured procedures / MS originated call / early assignment / HSCSD / non-transparent | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.1.1 Conformance requirements | 1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.1.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, displays the dialled number in the way described in a PICS/PIXIT statement.
2) To verify that the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.1.3 Method of test | Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
- Way to display th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.2 Multislot signalling / Structured procedures / MS originated call / late assignment / HSCSD / non-transparent | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.2.1 Conformance requirements | 1) An MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS , shall start to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.2.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL R... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.2.3 Method of test | Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
- Way to display th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.3 Multislot signalling / Structured procedures / MS originated call / early assignment / HSCSD / Transparent | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.3.1 Conformance requirement | 1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.3.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, displays the dialled number in the way described in a PICS/PIXIT statement.
2) To verify that the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.3.3 Method of test | Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
- Way to display th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.4 Multislot signalling / Structured procedures / MS Terminated call / early assignment / HSCSD / non-transparent | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.4.1 Conformance requirement | 1) The MS is in MM state "idle, updated" and in RR idle mode when being paged by the network.
2) The MS sends CHANNEL REQUEST message to the network and after that it receives IMMEDIATE ASSIGNMENT message from the network
3) The MS sends PAGING RESPONSE message to network and after that MS sends its multislot class in ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.4.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, after being paged by the network on the correct paging subchannel, after initiating the immediate assignment procedure by sending the CHANNEL REQUEST message, after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.4.3 Method of test | Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
• Multislot class (TSPC_Type_Multislot_ClassX)
• Immediate connect supported for all... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.5 Multislot signalling / Structured procedures / MS Terminated call / early assignment / HSCSD / Transparent | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.5.1 Conformance requirement | 1) The MS is in MM state "idle, updated" and in RR idle mode when being paged by the network.
2) The MS sends CHANNEL REQUEST message to the network and after that it receives IMMEDIATE ASSIGNMENT message from the network.
3) The MS sends PAGING RESPONSE message to network and after that MS sends its multislot class in... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.5.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, after being paged by the network on the correct paging subchannel, after initiating the immediate assignment procedure by sending the CHANNEL REQUEST message, after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.5.3 Method of test | Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
• Multislot class (TSPC_Type_Multislot_ClassX)
• Immediate connect supported for all... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.6 Default test conditions during layer 3 tests | During tests in subclause 26.13 the following default test conditions shall apply if not otherwise stated within the test description. In the table below, decimal values are normally used. Sometimes a hexadecimal value, indicated with a "H", or a binary value, indicated with a "B" is given.
GSM 450
GSM 480
General sign... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.7 Default contents of messages | ALERTING (mobile station to network direction)
Information element
Value/remark
Facility
Not checked
User-user
Not checked
SS version
Not checked
ALERTING (network to mobile station direction)
Information element
Value/remark
Facility
Omitted
Progress indicator
Omitted
User-user
Omitted
ASSIGNMENT COMMAND
Information e... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1 VGCS-VBS / Notification | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.1 VGCS-VBS / Notification / notification indication | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.1.1 Conformance requirement | 1. Having received a NOTIFICATION/NCH or NOTIFICATION/FACCH which contains group call reference(s) that are active in the MS, the MS shall correctly indicate the notified group/broadcast call reference(s).
2. On request to respond to the call notification, the MS shall join the VGCS/VBS call on the correct channel if a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.1.2 Test purpose | 1. To verify that the MS indicates correctly the notified group/broadcast call reference(s) after receiving a NOTIFICATION/NCH or NOTIFICATION/FACCH message which contains group call reference(s) that are active in the MS.
2. To verify that the MS, on request to respond to a call notification, joins the VGCS/VBS call o... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.1.3 Method of test | Initial Conditions
System Simulator:
1 cell default parameters for ASCI testing
Mobile Station:
The MS is in MM-state "idle, updated". No automatic answering is configured.
Specific PICS statements:
- Support VGCS talking (TSPC_AddInfo_VGCS_Talking)
- Support VBS originating (TSPC_AddInfo_VBS_Originating)
PIXIT Stateme... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.2 VGCS-VBS / Notification / NCH position | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.2.1 Conformance requirement | The MS shall recognise correctly different NCH positions and blocks if supporting VGCS or VBS.
In the case the CCCH configuration is not compatible with the NCH position, the MS shall behave as if the NCH position field was not present.
Reference(s)
3GPP TS 05.02, subclauses 6.5.1 and 6.5.5, clause 7 and table 3.
3GPP ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.2.2 Test purpose | To verify that the MS recognises correctly different NCH positions of first block and number of blocks.
To verify that the MS behaves as if the NCH position field was not present when the CCCH configuration is not compatible with the NCH position. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.2.3 Method of test | Initial Conditions
System Simulator:
1 cell, BS_AG_BLKS_RES = 5, CCCH non-combined.
Mobile Station:
The MS is in MM-state "idle, updated". No automatic answering is configured.
Specific PICS statements:
-
PIXIT Statements:
- Way to configure VGCS or VBS.
- Way to indicate a call notification.
Foreseen Final State of th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.3 VGCS-VBS / Notification / Reduced NCH monitoring | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.3.1 Conformance requirement | 1. When the mobile station in idle mode enters a cell and deduces from the BCCH that an NCH is present, it shall read the NCH until it has received at least two messages on the NCH indicating NLN, with the two last received NLN being identical. Then it may stop reading the NCH until it receives on the PCH an NLN(PCH) d... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.3.2 Test purpose | To verify that:
1. when the MS in idle mode on a cell where a reduced monitoring is activated, it reads the NCH until it has received at least two NLN (NCH) being identical. Then it stops reading the NCH until it receives a PAGING REQUEST message of any TYPE containing an NLN (PCH) different from the last previously re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.3.3 Method of test | Initial Conditions
System Simulator:
2 cells with default parameters for ASCI testing, same LAI.
The values specified in Table 26.14.1.3 override the values in default contents of SI messages in subclauses 26.6.14. and 26.6.15.
Table 26.14.1.3: Default values of the system information fields
Parameter
3GPP TS 04.08 / 3... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.4 VGCS-VBS / Notification / Limited Service state | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.4.1 Conformance requirement | In state MM IDLE and service state LIMITED SERVICE:
1. The MS shall indicate notifications to the GCC or BCC sub-layer for which a channel description has been received in the notification by the RR sub-layer.
2. The MS shall reject requests of the GCC or BCC sub-layer to respond to notifications for which no channel d... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.4.2 Test purpose | To verify that while in state MM IDLE and service state LIMITED SERVICE:
1. The MS rejects requests from user to respond to notifications for which no channel description has been received in the notification by the RR sub-layer.
2. The MS indicates notifications for which a channel description has been received in the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.1.4.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
The MS, with SIM, is in MM-state "idle, limited service" because LA not allowed.
Specific PICS statements:
- Support VGCS originating (TSPC_AddInfo_VGCS_Originating)
- Support VBS originating (TSPC_AddInfo_VBS_Originat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.2 VGCS-VBS / Paging | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.2.1 VGCS-VBS / Paging / Paging indication | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.2.1.1 Conformance requirement | 1. Paging into on-going voice group calls shall be provided as an implementation option.
2. In group receive mode the MS shall be ready to receive paging information on the FACCH containing the mobile subscriber identity and the priority level if eMLPP applies.
3. In group transmit mode if the MS has received a paging ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.2.1.2 Test purpose | It is checked that:
1. When the MS in group receive mode if a NOTIFICATION/FACCH message on the voice group call channel containing in-band paging information is received, the MS provides an indication with the correct priority if applicable.
2. When the MS in group receive mode if a paging message with the own mobile ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.2.1.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
No automatic answering configured.
Specific PICS statements:
- Support VGCS talking (TSPC_AddInfo_VGCS_Talking)
- Support VBS originating (TSPC_AddInfo_VBS_Originating)
- Support eMLPP (TSPC_Serv_eMLPP)
- Support monit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.2.2 VGCS-VBS / Paging / Notification | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.2.2.1 Conformance requirement | A PAGING REQUEST TYPE 1 message may have an additional notification coded in the P1 rest octets information element. It allows to notify the mobile an emergency group or broadcast call even when the MS at the moment does not monitor the NCH channel.
Reference(s)
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.2.1, 3.3.3.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.2.2.2 Test purposes | To verify that:
1. the MS in idle mode indicates correctly an incoming broadcast or group call when having received a PAGING REQUEST TYPE 1 message whose P1 rest octets information element contains group call information addressing the MS.
2. the MS in group receive mode indicates correctly an incoming broadcast or gro... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.2.2.3 Method of test | Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
The MS is in MM-state "idle, updated" with a TMSI allocated.
Specific PICS statements:
- Support VGCS talking (TSPC_AddInfo_VGCS_Talking)
- Support VBS originating (TSPC_AddInfo_VBS_Originating)
PIXIT Statements:
- Way... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3 VGCS-VBS / RR Procedures | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3.1 VGCS-VBS / RR Procedures / frequency redefinition | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3.1.1 Conformance requirements | The MS, after receiving a FREQUENCY REDEFINITION message in group transmit mode, shall start using the new frequencies and hopping sequence in the correct time slot.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.5. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3.1.2 Test purpose | To verify that after receiving a FREQUENCY REDEFINITION message in group transmit mode, the MS starts using the new frequencies and hopping sequence at the time indicated in the message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3.1.3 Method of test | Initial Conditions
System Simulator:
1 cell, CCCH_CONF set to 1 basic physical channel used for CCCH, not combined with SDCCHs. The cell allocation is set to CA450(1), CA480(1), CAPGSM(1), CADCS(1), CAPCS(1), CA710(1), CA750(1), CA810(1) or CA850(1), depending on the band of operation of the Mobile Station (See PICS/P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3.2 VGCS-VBS / RR Procedures / assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3.2.1 Conformance requirements | 1. Upon receipt of the ASSIGNMENT COMMAND message in group transmit mode, the mobile station shall initiate a local end release of link layer connections, disconnect the physical channels, command the switching to the assigned channels and initiate the establishment of lower layer connections (this includes the activat... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3.2.2 Test purpose | 1. To verify that upon receipt of an ASSIGNMENT COMMAND in group transmit mode, the MS switches to the channel defined in the ASSIGNMENT COMMAND, establishes the link and sends an ASSIGNMENT COMPLETE message.
1.1 from non-hopping TCH/F to hopping TCH/F using a different timeslot;
1.2 from hopping TCH/F to non-hopping T... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3.2.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters except:
Band
BCCH ARFCN
Throughout the test, the CA broadcast in System Information 1 is
GSM 450
263
259, 261, 263, 265, 267, 269, 271, 273, 275, 277
GSM 480
310
306, 308, 310, 312, 314, 316, 318, 320, 322, 324
GSM 710
457
447, 454, 457, 463, 471, 479, 482... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.14.3.3 VGCS-VBS / RR Procedures / handover / successful in group transmit mode | This clause deals with signalling tests in non-synchronised handover in successful case.
Table 26.14.3.3.1 contains a summary of the different combinations of parameters which have to be tested. For execution counter=3, the target channel is dedicated mode.
Table 26.14.3.3.1
From
To
Timing Adv.
Start
Time
Sync
?
State
... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.