hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.4.1 Conformance requirement | 1) In acceptance to a SETUP message indicating speech, the MS shall indicate and include in the CALL CONFIRMED message all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message specifying either speech full rate version 1 or speech full rate version 2 or speech half rate version 1 (for... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.4.2 Test purpose | 1) To verify that, in acceptance to a SETUP message indicating speech, the MS indicates and includes in the CALL CONFIRMED message all the speech versions that it supports.
2) To verify that upon receipt of the ASSIGNMENT COMMAND message specifying either speech full rate version 1 or speech full rate version 2 or spe... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.4.3 Method of test | Specific PICS statements:
- Speech supported for Half rate version 1 (TSPC_AddInfo_Half_rate_version_1)
- Immediate connect supported for all circuit switched basic services. (TSPC_AddInfo_ImmConn)
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Initial Conditi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.5 Structured procedures / emergency call | NOTE: This test is derived from the ones described in subclauses 26.9.6.1.1 and 26.9.6.1.2 and respectively entitled "Structured procedures / emergency call / idle updated, preferred channel rate " and "Structured procedures / emergency call / idle updated, non-preferred channel rate".
This test applies to mobiles supp... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.5.1 Conformance requirement | 1) For R97/98 MS: The MS in the "idle, updated" state, as after a successful location update, after the number 112 (for GSM 900 and 1 DCS 800 MS), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850, PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850, PCS 1 900 MS in Mexico) has been entered ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.5.2 Test purpose | 1) To verify that an R97/98 MS supporting speech in the MM state "idle, updated", when made to call the number 112, (for GSM 900 and DCS 1800 MS), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in Mexico) sends a CHA... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.5.3 Method of test | Specific PICS statements:
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Use of R99 Emergency numbers (TSPC_R99_Emerg)
PIXIT statements:
- .
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI an... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.6 EFR Signalling / Directed Retry / Mobile Originated Call | This test is derived from the one defined in subclause 26.9.7 and entitled "Directed Retry / MS originated call". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.6.1 Conformance requirements | The MS shall correctly apply the Directed Retry procedure from SDCCH/8 (no frequency hopping) to TCH/EFR with frequency hopping in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "mobile originating call proceeding" state shall, upon receipt of a CONNECT message... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.6.2 Test purpose | To test that, when the MS is ordered to perform a non-synchronized handover after the CALL PROCEED message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advanc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.6.3 Method of test | Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below.
Cell Allocation = Allocate as per the table below. PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
PLMN_PERM = 00001010.
Cell B has:
BCCH ARFCN =See the t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.7 EFR Signalling / Directed Retry / Mobile Terminated Call | This test is applicable to all MS which support EFR speech.
NOTE: This test is derived from the one defined in subclause 26.9.8 and entitled "Directed Retry / MS originated call". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.7.1 Conformance requirements | The MS shall correctly apply the Directed Retry procedure from SDCCH/8 with frequency hopping to TCH/EFR with frequency hopping and starting time in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "call delivered" state shall, if the MS supports immediate connec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.7.2 Test purpose | To test that when the MS is ordered to perform a non-synchronized handover after the CALL CONFIRM message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.7.3 Method of test | Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below
Cell Allocation = Allocate as per the table below.
PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
PLMN_PERM = 00001010.
Cell B has:
BCCH ARFCN = See the t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.12.8 Default contents of layer 3 messages for Enhanced Full rate speech tests | Refer to table 26.6, except for:
Contents of ASSIGNMENT COMMAND message:
Protocol Discriminator
RR Management
Skip Indicator
0000
Message Type
00101110
Channel Description
- Channel Type and TDMA offset
TCH/F + ACCHs
- Timeslot Number
Chosen arbitrarily by the test house
- Training Sequence Code
Chosen arbitrarily by t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1 Multislot signalling / RR | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1 Multislot signalling / RR / Measurement | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.1 Multislot signalling / RR / Measurement / symmetric | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.1.1 Conformance requirements | The MS shall continuously send MEASUREMENT REPORT messages, on every uplink HSCSD channel used, on every SACCH blocks and the measurement valid indication shall be set to valid (0) within the second block at the latest. After 20 s the values in the MEASUREMENT REPORT message shall contain measurement results for the 4 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.1.2 Test purpose | 1) To test that, when a combination of normal neighbours, and non-permitted NCCs is "on air", the MS reports only on normal neighbours and that in symmetric HSCSD configuration the neighbouring cell measurement reports are copied on every uplink HSCSD channel used. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.1.3 Method of test | Initial Conditions
System Simulator:
For GSM 450 or GSM 480: 8 cells with the following settings:
Transmitter
Level
NCC
BSCC
ARFCN
ARFCN
Cell Identity
(GSM 450)
(GSM 480)
Serving, S1
‑60
1
3
260
307
0001H
Neighbour, N1
‑85
1
5
264
311
0002H
Neighbour, N2
‑80
1
7
268
315
0003H
Neighbour, N3
‑75
2
1
272
319
0004H
Neighbo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.2 Multislot signalling / RR / Measurement / asymmetric | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.2.1 Conformance requirements | The MS shall continuously send MEASUREMENT REPORT messages, on every uplink HSCSD channel used, on every SACCH blocks and the measurement valid indication shall be set to valid (0) within the second block at the latest. After 20 s the values in the MEASUREMENT REPORT message shall contain measurement results for the 4 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.2.2 Test purpose | 1) To test that, when a combination of normal neighbours, barred cells and non-permitted NCCs is "on air", the MS reports only on normal neighbours and that in asymmetric HSCSD configuration the neighbouring cell measurement reports are copied on every uplink HSCSD channel used. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.2.3 Method of test | Initial Conditions
System Simulator:
For GSM 450 or GSM 480: 8 cells with the following settings:
Transmitter
Level
NCC
BSCC
ARFCN
ARFCN
Cell Identity
(GSM 450)
(GSM 480)
Serving, S1
‑60
1
3
260
307
0001H
Neighbour, N1
‑85
1
5
264
311
0002H
Neighbour, N2
‑80
1
7
268
315
0003H
Neighbour, N3
‑75
2
1
272
319
0004H
Neighbo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.3 Multislot signaling / RR / Measurement / asymmetric / change of the reported subchannel | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.3.1 Conformance requirements | The MS shall continuously send MEASUREMENT REPORT messages, on the main channel, reporting the worst subchannel. One of the other subchannels is made worse than the one originally reported one and the MEASUREMENT REPORTs sent on the main channel are based on the new worst subchannel.
References
3GPP TS 04.08 / 3GPP TS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.3.2 Test purpose | 1) To test that the MS shall report on the main SACCH: RXLEV_FULL and RXLEV_SUB from the main channel and the worst RXQUAL_FULL values and RXQUAL_SUB values from the main channel and the unidirectional channels.
2) To test that, when an another subchannel becomes the worst, MEASUREMENT REPORTs sent on the main channel ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.1.3.3 Method of test | Initial Conditions
System Simulator:
For GSM 450 or GSM 480: 1 cell with the following settings:
Transmitter
Level
NCC
BCC
ARFCN
ARFCN
Cell Identity
(GSM 450)
(GSM 480)
Serving, S1
‑60
1
3
260
307
0001H
For GSM 900 or DCS 1 800: 1 cell with the following settings:
Transmitter
Level
NCC
BCC
ARFCN
ARFCN
Cell Identity
(GS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.2 Multislot signalling / RR / Dedicated assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.2.1 Multislot signalling / RR / Dedicated assignment / successful case | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.2.1.1 Conformance requirements | 1) Upon receipt of the ASSIGNMENT COMMAND message, the mobile station initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, thei... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.2.1.2 Test purpose | 1) To verify that upon receipt of an ASSIGNMENT COMMAND, the MS switches to the channel(s) defined in the ASSIGNMENT COMMAND, establishes the link and sends an ASSIGNMENT COMPLETE message. This is tested for an MS supporting TCH and multislot configuration in the special cases of a transition.
1.1) from non-hopping SDC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.2.1.3 Method of test | Initial Conditions
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
GSM 450:
- BCCH ARFCN =263.
- Throughout the test, the CA broadcast in System Information 1 is (259, 261, 263, 265, 267, 269, 271, 273, 275, 277).
- Note that the actual CA of the cell contain... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.2.2 Multislot signalling / RR / Dedicated assignment / failure / general case | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.2.2.1 Conformance requirements | On the mobile station side, if a lower layer failure happens on the new channel before the ASSIGNMENT COMPLETE message has been sent, the mobile station deactivates the new channels, reactivates the old channels, reconnects the TCHs if any and triggers the establishment of the main signalling link. It then sends an ASS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.2.2.2 Test purpose | 1) To test that, when the MS fails to seize the new channel, the MS reactivates the old channel.
2) This is tested in the special cases of transition:
2.1) from non-hopping SDCCH to hopping symmetric multislot configuration;
2.2) from hopping asymmetric multislot configuration to non-hopping symmetric;
2.3) from non ho... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.2.2.3 Method of test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is "idle updated".
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen Final State of the MS
The MS is "idle updated".
Test Procedure
A mobile terminated RR connection is established... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3 Test of handover | With the Handover procedure, it is possible to completely alter the channels allocated to a MS. This makes it possible in particular to switch a call in progress from one cell to another. The procedure is always initiated by the network and with the MS in a dedicated mode.
Subclauses 26.13.1.3.1 to 26.13.1.3.5 contain ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.1 Multislot signalling / RR / Handover / successful / active call / non-synchronized | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.1.1 Conformance requirements | 1) The MS shall correctly apply the handover procedure in the non-synchronized case when a multislot connection is in progress and when handover is performed from a non-hopping multislot configuration towards a hopping multislot configuration.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 44.018 subclau... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.1.2 Test purpose | 1) To test that when the MS is ordered to make a non-synchronized handover from non-hopping multislot configuration to hopping multislot configuration, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS.
2) To test that the MS ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.1.3 Method of test | Initial Conditions
System Simulator:
- 2 cells, A and B with same LAI, default parameters except:
- Early classmark sending enabled in SI3 rest octets
GSM 450:
Cell A has:
- BCCH ARFCN = 263
Cell B has:
- BCCH ARFCN = 274
- Cell Allocation = (260, 262, 264, 266, 268, 270, 272, 274, 276, 279, 281, 283, 285, 287, 289, 29... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.2 Multislot signalling / RR / Handover / successful / call under establishment / non synchronized / resource upgrading | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.2.1 Conformance requirements | 1) The MS shall correctly apply the handover procedure from non-hopping multislot configuration to non-hopping multislot configuration in the non-synchronized case during call establishment.
2) The MS shall activate the new channels that belongs to same multislot configuration correctly, taking into account upgraded re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.2.2 Test purpose | 1) To test that when the MS is ordered to make a non-synchronized handover from non-hopping multislot configuration to a non-hopping multislot configuration, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS.
2) To test that t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.2.3 Method of test | Initial Conditions
System Simulator:
- 2 cells, A and B with same LAI, default parameters except:
- Early classmark sending enabled in SI3 rest octets
GSM 450:
Cell A has:
- BCCH ARFCN = 263
- PLMN colour code, NCC = as defaults.
- BS colour code, BCC = as defaults.
- PLMN_PERM = 00001010.
Cell B has:
- BCCH ARFCN = 27... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.3 Multislot signalling / RR / Handover / successful / active call / finely synchronized / resource downgrading | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.3.1 Conformance requirements | 1) The MS shall correctly apply the handover procedure from multislot configuration with frequency hopping to multislot configuration without frequency hopping in the finely synchronized case when a call is in progress. Resources are downgraded in handover procedure.
References
Conformance requirement 1: 3GPP TS 04.08 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.3.2 Test purpose | 1) To test that when the MS is ordered to make a finely synchronized handover to a synchronized cell from a hopping multislot configuration to a non-hopping multislot configuration, it sends 4 access bursts on the main DCCH (before completion, additional access bursts may also be sent on the SACCH) and then activates t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.3.3 Method of test | Initial Conditions
System Simulator:
- 2 cells, A and B, with same LAI, default parameters, except:
- Early classmark sending enabled in SI3 rest octets- The BCCH of cell A is sent k bit periods before the BCCH of cell B. The timing advance in cell A sent to the MS is y bit periods. k and y are selected such that 0 < (... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.4 Multislot signalling / RR / Handover / successful / call under establishment / finely synchronized / relocation of channels | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.4.1 Conformance requirements | 1) The MS shall correctly apply the handover procedure from hopping, multislot configuration, finely synchronized case to hopping, multislot configuration, synchronized case during call establishment.
2) The MS shall not change number of channels in multislot configuration but the place of each channel is changed.
3) I... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.4.2 Test purpose | 1) To test that when the MS is ordered to make a finely synchronized handover to a synchronized cell, it sends 4 access bursts on the main DCCH (before completion, additional access bursts may also be sent on the SACCH) and then activates the channel correctly, taking into account power command, new order of channels i... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.4.3 Method of test | Initial Conditions
System Simulator:
- 2 cells, A and B, with same LAI, default parameters, except:
- Early classmark sending enabled in SI3 rest octets.
- The BCCH of cell A is sent k bit periods before the BCCH of cell B. The timing advance in cell A sent to the MS is y bit periods. k and y are selected such that 0 <... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.5 Multislot signalling / RR /Handover / successful / call under establishment / pre-synchronized / resource upgrading | If an MS does not implement the pre-synchronized handover procedure correctly then calls may fail.
If an MS does not report the observed time difference between cells correctly then pseudo synchronized handovers might not be possible for any MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.5.1 Conformance requirements | 1) If during call establishment a Layer 3 MM or CC message just sent by the MS is not Layer 2 acknowledged before the channel change caused by the HANDOVER COMMAND message, the MS shall send the Layer 3 message to the new cell, using the same value in the N(SD) field, after the handover procedure.
2) When the Timing Ad... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.5.2 Test purpose | 1) To verify that when the MS is ordered to make a pre-synchronized handover from hopping multislot configuration to non-hopping multislot configuration, it sends 4 access bursts on the main DCCH (before completion, additional access bursts may also be sent on the SACCH) and then activates the channel correctly and cor... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.3.5.3 Method of test | Initial Conditions
System Simulator:
- 2 cells, A and B, with same LAI, default parameters, except:
- Early classmark sending enabled in SI3 rest octets.
- The BCCH of cell A is sent k bit periods before the BCCH of cell B.
Mobile Station:
- The MS is in the "idle, updated" state, with a TMSI allocated and camped on ce... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.4 Multislot signalling / RR / Test of the channel mode modify procedure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.4.1 Conformance requirements | 1) When the MS has received the CHANNEL MODE MODIFY message, the mobile station changes the mode for the indicated channel and then replies by a CHANNEL MODE MODIFY ACKNOWLEDGE message indicating the new channel mode.
2) If the mobile station does not support the indicated mode, it shall retain the old mode and return ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.4.2 Test purpose | 1) To verify that the MS, in an RR connected state, acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGEMENT message specifying and switching to the correct mode for the channels in a multislot configuration:
- the new mode if that mode is supported;
- the old mode if the new mode is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.4.3 Method of test | Initial Conditions
System Simulator:
- 1 cells, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Mobile Station:
- The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
• Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
supported radio interface rates: 12k... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.5 Multislot signalling / RR / Early classmark sending | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.5.1 Conformance requirement | 1) MS uses Controlled Early Classmark Sending procedure when indicated in SYSTEM INFORMATION TYPE 3 (ES ind bit in SI 3 Rest Octets).
1.1) If Controlled Early Classmark Sending is not allowed by network the MS does not send a CLASSMARK CHANGE message.
1.2) If Controlled Early Classmark Sending is allowed by network the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.5.2 Test purpose | 1) To verify that the MS sends its multislot class in Mobile Station Classmark 3 using Controlled Early Classmark Sending procedure if allowed by network.
2) To verify that the MS does not perform Early Classmark Sending if it is not allowed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.5.3 Method of test | Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
MS is in MM-state "idle, updated... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.1.6 Default contents of layer 3 messages for RR tests | 26.13.1.6.1 Default contents of GSM 900 layer 3 messages for RR tests
This subclause contains the default values of GSM 900 L3 messages, which unless indicated otherwise in subclause 26.13 shall be transmitted by the system simulator and which are required to be received from the GSM 900 MS under test.
The necessary L3... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2 Multislot signalling / CC | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1 Multislot signalling / CC / In-call functions | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1 Multislot signalling / CC / In-call functions / User initiated service level upgrade / successful | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1.1 Definition | Multislot connection is established. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is successfully performed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1.2 Conformance requirements | 1) MS shall send MODIFY message to SS indicating that User initiated service level upgrade is initiated.
2) MS enters CC state 'Mobile originating modify (U26)' after sending MODIFY.
3) MS enters CC state 'Active (U10)' when MODIFY COMPLETE is received.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.0... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1.3 Test purpose | 1) To verify that the procedure is initiated by the MS in the "active" state of a multislot connection. It sends a MODIFY message including the wanted value of the "maximum number of traffic channels" and/or the "wanted air interface" parameters; and enters the "mobile originating modify" state. Other parameters of the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.1.4 Method of test | Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection.
System simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.2 Multislot signalling / CC / In-call functions / User initiated service level downgrade / successful | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 25.13.2.1.2.1 Definition | Multislot connection is established. Multislot configuration has the maximum number of timeslots supported by the MS. User initiated service level downgrade is successfully performed. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.2.2 Conformance requirements | 1) MS shall send MODIFY message to SS indicating that User initiated service level downgrade is initiated.
2) MS enters CC state 'Mobile originating modify (U26)' after sending MODIFY.
3) MS enters CC state 'Active (U10)' when MODIFY COMPLETE is received.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.2.3 Test purpose | 1) To verify that the procedure is initiated by the MS in the "active" state of a multislot connection. It sends a MODIFY message including the wanted value of the "maximum number of traffic channels" and/or the "wanted air interface" parameters; and enters the "mobile originating modify" state. Other parameters of the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.2.4 Method of test | Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection. Multislot configuration has maximum number of timeslots supported by the MS.
System simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Specific PICS statements:
- Mult... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3 Multislot signalling / CC / In-call functions / User initiated service level upgrade / Time-out of timer T323 | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3.1 Definition | Multislot connection is established. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is requested. Timer T323 expires. Call is cleared. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3.2 Conformance requirements | 1) MS shall send MODIFY message to SS indicating that User initiated service level upgrade is initiated.
2) After timer T323 has expired MS starts call clearing by sending DISCONNECT message.
3) After receipt of RELEASE message the MS sends RELEASE COMPLETE message and goes to idle updated state.
References
Conformance... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3.3 Test purpose | 1) To verify that upon expiration of T323 (accuracy ± 10%) the MS shall initiate the procedures for call clearing with cause #102 "recovery on timer expiry". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.3.4 Method of test | Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection.
System simulator:
- 1 cell, default parameters
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final state of the MS
"Idle, updated", with TMSI allocated.
Test pro... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4 Multislot signalling / CC / In-call functions / User initiated service level upgrade / modify reject | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4.1 Definition | Multislot connection is established. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is requested. SS responds to upgrade request by rejecting it. MS enters the active multislot connection state. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4.2 Conformance requirements | 1) MS shall send MODIFY message to SS indicating that User initiated service level upgrade is initiated.
2) MS enters CC state 'Mobile originating modify (U26)' after sending MODIFY.
3) MS enters CC state 'Active (U10)' when MODIFY REJECT is received.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4.3 Test purpose | 1) To verify that upon receipt of the MODIFY REJECT message with the bearer capability negotiated at the call setup, the MS is continuously sending user information according to current call mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.4.4 Method of test | Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection.
System simulator:
- 1 cell, default parameters
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final state of the MS
MS is in the active state of a service using a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.2.1.5 Multislot signalling / CC / In call functions / contents of some of the messages | The following messages are used for testing in-call modification procedures, test cases 26.13.2.1.*, as default messages for those ones defined below. If any other values are defined in the expected sequence of the actual test cases, those values take precedence over the ones defined hereafter.
SETUP (MS to SS)
Informa... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3 Multislot signalling / Structured procedures | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.1 Multislot signalling / Structured procedures / MS originated call / early assignment / HSCSD / non-transparent | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.1.1 Conformance requirements | 1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.1.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, displays the dialled number in the way described in a PICS/PIXIT statement.
2) To verify that the... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.1.3 Method of test | Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
- Way to display th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.2 Multislot signalling / Structured procedures / MS originated call / late assignment / HSCSD / non-transparent | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.2.1 Conformance requirements | 1) An MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS , shall start to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.13.3.2.2 Test purpose | 1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL R... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.