hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.6.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.6.2 Test purpose | To verify that during a mobile originated call, the MS applies TSC set and different channel rates during handover from VAMOS to non VAMOS mode |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.6.3 Method of Test | Initial Conditions
System Simulator:
2 cells, default parameters.
Cell A: TSC as defined in table 26.21-1 Cell A TSC set for execution counter M.
Cell B: TSC as defined in table 26.21-1 Cell B TSC set for execution counter M.
Mobile Station:
in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.7 VAMOS Signalling / Emergency call | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.7.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.7.2 Test purpose | To verify for emergency call setup procedure that the MS applies the correct VAMOS TSC set allocated by ASSIGNMENT COMMAND message. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.7.3 Method of Test | Initial Conditions
System Simulator:
1 cell, default parameters, TSC as defined in table 26.21-1 Cell A TSC set for execution counter M.
Mobile Station:
in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:
- VAMOS II supported ( TSPC_VAMOS_Type2)
- VAMOS III supported (TSPC_VAMOS_Type3)
- Spee... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.8 VAMOS Signalling / MS Originated call / Early assignment / Handover to different AMR codec rates | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.8.1 Conformance requirements | 1) VAMOS allows multiplexing of two users simultaneously on the same physical resource in the circuit switched mode both in downlink and in uplink, using the same timeslot number, ARFCN and TDMA frame number. Hence, a basic physical channel capable of VAMOS supports up to 4 TCH channels along with their associated cont... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.8.2 Test purpose | To verify that during a mobile originated call and after handover procedure the MS applies TSC set and different AMR codec rates in VAMOS mode. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.21.8.3 Method of Test | Initial Conditions
System Simulator:
2 cells, default parameters.
Cell A: TSC as defined in table 26.21-1 Cell A TSC set for execution counter M.
Cell B: TSC as defined in table 26.21-1 Cell B TSC set for execution counter M.
Mobile Station:
in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22 Test of other features | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22.1 Layer 2 fill bits randomisation | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22.1.1 Conformance requirements | The end of the useful part of the frame, i.e. the octets following the length indicator field in type A frames and the octets following the information field in type B frames, is determined by a length indicator contained in the length indicator field. The useful part of a Bbis frames takes all N201 octets of that fram... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22.1.2 Test purpose | An MS shall correctly decode all LAPDm frames with randomised fill bits.
An MS supporting randomisation of fill bits in the Uplink direction shall a) correctly encode the first octet of a frame containing fill bytes and b) send a random sequence of bits during a signalling sequence. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 26.22.1.3 Method of Test | Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is switched off.
Specific PICS statements:
- L2 fill bits randomisation in uplink (TSPC_UL_L2_Fill_Bits_Randomisation)
- at least one short message service (TSPC_AddInfo_SMS)
- MSsupporting at least one bearer capability service (TS... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1 MS identification by short IMSI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1 MS identification by short IMSI - Normal case | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.1 Definition | The IMSI is used for unique identification of the MS by a GSM network. The IMSI is stored in the SIM and read during the SIM/ME initialization procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.2 Conformance requirement | On the receipt of an IMMEDIATE ASSIGNMENT message the MS shall send PAGING RESPONSE containing the IMSI of the SIM.
3GPP TS 11.11, subclauses 11.2.1 and 11.4.2, 3GPP TS 04.08 / 3GPP TS 24.008, subclause 10.5.1.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.3 Test purpose | 1) To verify that the ME uses the IMSI of the SIM.
2) To verify that the ME can handle an IMSI of less than the maximum length. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI-MCC: 246
LAI-MNC 81 or 813 (see Note 0)
LAI-LAC: 0001
Access control: unrestricted.
The default SIM is installed into the ME and the MS is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.4.2 Procedure | a) The SS sends PAGING REQUEST to the MS using the IMSI stored in the SIM.
b) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
c) After receipt of a PAGING RESPONSE from the MS, the SS sends CHANNEL RELEASE to the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.1.5 Test requirement | After step b) the MS shall send PAGING RESPONSE to the SS containing the IMSI stored in the SIM.
27.1.1a MS identification by short IMSI - for GPRS
27.1.1a.1 Definition
The IMSI is used for unique identification of the MS by a GSM network. The IMSI is stored in the SIM and read during the SIM/ME initialization procedur... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2 MS identification by short IMSI, Phase 1 DCS SIM | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.1 Definition | Different from Phase 2, the IMSI in a Phase 1 DCS SIM is stored in a directory DFDCS1800 with the specific identifier "7F 21". To ensure backwards compatibility, if selection of the phase 2 identifier "7F 20" fails, the MS shall select "7F 21". Otherwise access to the IMSI and other data is impossible with a Phase 1 DC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.3 Test purpose | To verify that the ME uses the identifier "7F 21" to select DFDCS1800 in a Phase 1 DCS SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI (MCC/MNC/LAC): 246/81/0001.
Access control: unrestricted.
A phase 1 DCS SIM (identifier of DFDCS1800 is "7F 21", DFGSM not existing) with default values is installed into the ME and the MS is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.4.2 Procedure | a) The SS sends PAGING REQUEST to the MS using the IMSI stored in the SIM.
b) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
c) After receipt of a PAGING RESPONSE from the MS, the SS sends CHANNEL RELEASE to the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.1.2.5 Test requirement | After step b) the MS shall send PAGING RESPONSE to the SS containing the IMSI stored in the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2 MS identification by short TMSI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.1 Definition | The TMSI is temporarily used for identification of the MS by a GSM network. It will have been previously assigned by the network. The TMSI is stored in the SIM by the ME and read during the SIM/ME initialization procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.2 Conformance requirement | On the receipt of an IMMEDIATE ASSIGNMENT message the MS shall send PAGING RESPONSE containing the TMSI stored in the SIM.
3GPP TS 11.11, subclauses 11.2.1 and 11.4.5, 3GPP TS 04.08 / 3GPP TS 24.008, subclause 10.5.1.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.3 Test purpose | 1) To verify that the ME uses the TMSI stored in the SIM.
2) To verify that the ME can handle a TMSI of less than maximum length. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI-MCC: 246
LAI-MNC 81 or 813 (see Note 0)
LAI-LAC: 0001
Access control: unrestricted.
The default SIM is used with the following exception.
EFLOCI (Location Information)
Logically: LAI-MCC: 246
LAI-MNC: 81 or 813 (See Note 0... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.4.2 Procedure | a) The SS sends PAGING REQUEST to the MS using the TMSI stored in the SIM.
b) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
c) After receipt of a PAGING RESPONSE from the MS, the SS sends CHANNEL RELEASE to the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.2.5 Test requirement | After step b) the MS shall send PAGING RESPONSE to the SS containing the TMSI stored in the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3 MS identification by long TMSI | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.1 Definition | The TMSI is temporarily used for identification of the MS by a GSM network. It will have been previously assigned by the network. The TMSI is stored in the SIM by the ME and read during the SIM/ME initialization procedure. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.2 Conformance requirement | On the receipt of an IMMEDIATE ASSIGNMENT message the MS shall send PAGING RESPONSE containing the correct TMSI stored in the SIM.
3GPP TS 11.11, subclauses 11.2.1 and 11.4.5, 3GPP TS 04.08 / 3GPP TS 24.008, subclause 10.5.1.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.3 Test purpose | 1) To verify that the ME uses the TMSI stored in the SIM.
2) To verify that the ME can handle a TMSI of maximum length.
3) To verify that the ME does not respond to page requests containing a previous TMSI. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.4.1 Initial conditions | Prior to this test, the ME shall have been operated with a SIM containing TMSI "2143". This will be achieved by executing the previous test (27.2) prior to this test. Only under this condition will test be verified.
The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI-MCC: 2... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.4.2 Procedure | a) The SS sends PAGING REQUEST to the MS using the TMSI "2143".
b) The SS sends PAGING REQUEST to the MS using the TMSI stored in the SIM.
c) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
d) After receipt of a PAGING RESPONSE from the MS, the SS sends CHANNEL RELEASE to th... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.3.5 Test requirement | 1) After step a) the MS shall not respond to the PAGING REQUEST.
2) After step c) the MS shall send PAGING RESPONSE to the SS containing the TMSI stored in the SIM. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.4 MS identification by long IMSI, TMSI updating and cipher key sequence number assignment | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.4.1 Definition | The IMSI and TMSI are used for identification of the MS by a GSM network. They are read from the SIM during the SIM/ME initialization procedure. Within the authentication procedure the network sends a cipher key sequence number to the MS. In addition the network may allocate a new TMSI to the MS. Cipher key sequence nu... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.4.2 Conformance requirement | 1. On the receipt of an IMMEDIATE ASSIGNMENT message the MS shall send PAGING RESPONSE containing the correct IMSI stored in the SIM.
3GPP TS 11.11, subclauses 11.2.1 and 11.4.2, 3GPP TS 04.08 / 3GPP TS 24.008, subclause 10.5.1.4.
2. After call termination the SIM shall contain the cipher key sequence number and TMSI r... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.4.3 Test purpose | 1) To verify that the ME uses the IMSI stored in the SIM.
2) To verify that the ME does not respond to page requests containing a previous IMSI.
3) To verify that the ME can handle an IMSI of maximum length.
4) To verify that the ME correctly updates the cipher key sequence number at call termination.
5) To verify that... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.4.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.4.4.1 Initial conditions | Prior to this test, the ME shall have been operated with a SIM containing IMSI "246813579". This will be achieved by executing the previous test (27.3) prior to this test. Only under this condition will this test be verified.
The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.4.4.2 Procedure | a) The SS sends PAGING REQUEST to the MS using the IMSI "246813579".
b) The SS sends PAGING REQUEST to the MS using the IMSI stored in the SIM.
c) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
d) After receipt of a PAGING RESPONSE from the MS, the SS sends AUTHENTICATION R... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.4.5 Test requirement | 1) After step a) the MS shall not respond to the PAGING REQUEST.
2) After step c) the MS shall send PAGING RESPONSE to the SS containing the IMSI stored in the SIM.
3) After step e) the MS shall send TMSI REALLOCATION COMPLETE to the SS.
4) After step g) the SIM shall contain the following values.
EFLOCI (Location Info... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.5 Forbidden PLMNs, location updating and undefined cipher key | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.5.1 Definition | A list of forbidden PLMNs stored in the SIM and providing storage for up to 4 entries is managed by the MS. In automatic PLMN selection mode the MS controls location updating attempts to appropriate networks with respect to this list of forbidden PLMNs. As a result of a location update reject with the cause "PLMN not a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.5.2 Conformance requirement | 1. In automatic PLMN selection mode the MS shall only attempt a LOCATION UPDATE if it receives a BCCH containing a LAI that is not indicated in the EFFPLMN in the SIM.
3GPP TS 02.11, subclause 2.3, 3GPP TS 11.11, subclauses 11.2.1 and 11.4.8.
2. After receipt of a LOCATION UPDATE REJECT message with the cause "PLMN not... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.5.3 Test purpose | 1) To verify that in automatic PLMN selection mode the MS does not attempt to access PLMNs stored in EFFPLMN on the SIM.
2) To verify that the EFFPLMN is correctly updated by the ME after receipt of a LOCATION UPDATE REJECT message with cause "PLMN not allowed".
3) To verify that the EFKc has been correctly updated by ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.5.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.5.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI-MCC: 234
LAI-MNC 02 or 023 (see Note 0)
LAI-LAC: 0001
Access control: unrestricted.
The default SIM is used with the following exception:
EFIMSI (IMSI)
Logically: 246811111111111 (2-digit MNC) or 246813111111111 (3-digit M... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.5.4.2 Procedure | a) The MS is powered on.
b) The SS stops all RF output on the BCCH for a long enough period of time to cause a cell reselection procedure in the MS. The BCCH is changed to contain:
LAI (MCC/MNC): 234/03 or 234/034 (see Note 0).
The SS then resumes RF output on the BCCH.
c) The SS stops all RF output on the BCCH for a l... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.5.5 Test requirement | 1) After each of the steps a) to d) the MS shall not attempt a LOCATION UPDATE.
2) After step f) the MS shall send LOCATION UPDATE REQUEST to the SS.
3) After step h) the MS shall send LOCATION UPDATE REQUEST to the SS.
4) After step i) the MS shall respond with TMSI REALLOCATION COMPLETE.
5) After step k) the SIM shal... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.6 MS updating forbidden PLMNs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.6.1 Definition | A list of forbidden PLMNs stored in the SIM provides storage for up to 4 entries, and is managed by the MS. In automatic PLMN selection mode the MS controls location updating attempts to appropriate networks with respect to this list of forbidden PLMNs. As a result of a location update reject with the cause "PLMN not a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.6.2 Conformance requirement | After the receipt of a LOCATION UPDATE REJECT message with the cause "PLMN not allowed" the MS shall update the EFFPLMN in the SIM.
3GPP TS 02.11, subclause 3.2.2.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.6.3 Test purpose | To verify that the MS correctly updates the EFFPLMN, i.e. fill up existing gaps in the elementary file before overwriting any existing entries. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.6.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.6.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI-MCC: 234
LAI-MNC 03 or 034 (see Note 0)
LAI-LAC: 0001
Access control: unrestricted.
The default SIM is used with the following exception:
Bands using 2-digit MNC (see Note 0) begin
EFFPLMN (Forbidden PLMNs)
Logically:
PLMN... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.6.4.2 Procedure | a) The MS is powered on.
b) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
c) After receipt of a LOCATION UPDATE REQUEST from the MS, the SS sends LOCATION UPDATE REJECT to the MS with the cause "PLMN not allowed", followed by CHANNEL RELEASE.
d) The MS is soft powered down... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.6.5 Test requirement | 1) After step b) the MS shall send LOCATION UPDATE REQUEST to the SS.
2) After step d) the SIM shall contain:
EFFPLMN (Forbidden PLMNs)
Logically:
PLMN1
PLMN2
PLMN3
PLMN4
MCC
234
234
234
234
MNC (See Note 0)
2-digit
Either
02
03
04
05
Or
02
04
05
03
3-digit
Either
023
034
045
056
Or
023
045
056
023
Coding:
B1
B2
B3
B4
... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.7 MS deleting forbidden PLMNs | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.7.1 Definition | In manual PLMN selection mode the MS allows location update attempts to all available PLMNs, including forbidden PLMNs (as indicated by the forbidden PLMN list on the SIM). As a result of a successful location update procedure onto a PLMN which is in the forbidden PLMN list, the forbidden PLMN list is automatically upd... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.7.2 Conformance requirement | 1. In manual PLMN selection mode the MS shall be able to perform a LOCATION UPDATE attempt to a PLMN which is in the forbidden PLMN list.
3GPP TS 02.11, subclause 3.2.2.2.
2. After receipt of LOCATION UPDATE ACCEPT the MS shall delete the forbidden PLMN from the forbidden PLMN list.
3GPP TS 02.11, subclause 3.2.2.4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.7.3 Test purpose | 1) To verify that in automatic PLMN selection mode the MS does not attempt to access PLMNs stored in EFFPLMN on the SIM.
2) To verify that the MS is able to perform a LOCATION UPDATE on a forbidden PLMN in manual PLMN selection mode.
3) To verify that the MS after a successful LOCATION UPDATE deletes the PLMN in the EF... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.7.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.7.4.1 Initial conditions | The SS transmits on the BCCH, with the following network parameters:
Attach/detach: disabled.
LAI-MCC: 234
LAI-MNC 01 or 012 (see Note 0)
LAI-LAC: 0001
Access control: unrestricted.
The default SIM is used with the following exception:
EFFPLMN (Forbidden PLMNs)
Logically: PLMN1: empty
PLMN2: empty
PLMN3: MCC: 234
MNC: ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.7.4.2 Procedure | a) The MS is powered on.
b) PLMN with MCC/MNC of 234/01 or 234/012 (see Note 0) is manually selected.
c) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
d) After receipt of a LOCATION UPDATE REQUEST from the MS, the SS sends LOCATION UPDATE ACCEPT with:
LAI-MCC: 234
LAI-MNC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.7.5 Test requirement | 1) After step a) the MS shall not attempt a LOCATION UPDATE.
2) After step c) the MS shall send LOCATION UPDATE REQUEST to the SS.
3) After step d) the MS shall respond with TMSI REALLOCATION COMPLETE.
4) After step f) the SIM shall contain the following values:
EFLOCI (Location Information)
Logically: LAI-MCC: 234
LAI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.8 MS updating the PLMN selector list | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.8.1 Definition | The PLMN selector list gives in priority order the preferred PLMNs on which the MS shall register. The list is stored on the SIM in the EFPLMNsel. Update and deletion of PLMNs may be performed by the subscriber. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.8.2 Conformance requirement | The MS shall correctly replace the selected PLMN in the PLMN selector list.
3GPP TS 11.11, subclause 11.5.5. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.8.3 Test purpose | To verify that the MS correctly updates the EFPLMNsel. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.8.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.8.4.1 Initial conditions | No SS is required for this test.
The default SIM is used.
The SIM is installed into the ME and the MS is powered on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.8.4.2 Procedure | a) The user shall initiate an MMI dependent procedure to change the second PLMN in the PLMN selector list to MCC/MNC of 567/01 or 567/018 (see Note 0).
b) The MS is soft powered down. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.8.5 Test requirement | After step b) the SIM shall contain the following values:
EFPLMNsel (PLMN Selector)
Logically:
PLMN
1st
2nd
3rd
4th
5th
6th
7th
8th
MCC
234
567
234
234
234
234
246
246
2-digit MNC
01
01
03
04
05
06
81
82
3-digit MNC
012
018
034
045
056
067
813
824
Coding:
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
2-digit MNC
32
F4
10
65
F... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.9 MS recognizing the priority order of the PLMN selector list | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.9.1 Definition | The PLMN selector list gives in priority order the preferred PLMNs on which the MS shall register. The list is stored on the SIM in the EFPLMNsel. Update and deletion of PLMNs may be performed by the subscriber by the use of the PIN. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.9.2 Conformance requirement | When registering onto a VPLMN the MS shall take into account the priority order of the PLMNs in the preferred list on the SIM.
3GPP TS 02.11, subclause 3.2.2.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.9.3 Test purpose | To verify that the PLMN with the higher priority (defined by its position in EFPLMNsel) takes precedence over the PLMN with the lower priority when the MS performs a network selection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.9.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.9.4.1 Initial conditions | The SS transmits on two BCCHs, with the following network parameters:
Attach / Detach
LAI
Access Control
MCC
MNC (2-digit)
MNC (3-digit)
LAC
BCCH 1
disabled
234
33
334
0001
unrestricted
BCCH 2
disabled
234
34
345
0001
unrestricted
The default SIM is used with the following exception:
EFPLMNsel (PLMN Selector)
Logically... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.9.4.2 Procedure | a) The MS is powered on.
b) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
c) After receipt of a LOCATION UPDATE REQUEST from the MS, the SS sends LOCATION UPDATE ACCEPT with:
LAI-MCC: 234
LAI-MNC 34 or 345 (see Note 0)
TMSI: "34567890".
to the MS
d) After receipt of a TMSI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.9.5 Test requirement | 1) After step b) the MS shall send LOCATION UPDATE REQUEST containing an MCC/MNC of 234/34 or 234/345 (see Note 0) to the SS.
2) After step c) the MS shall respond with TMSI REALLOCATION COMPLETE.
3) After step e) the SIM shall contain the following values:
EFLOCI (Location Information)
Logically: LAI-MCC: 234
LAI-MNC... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.10 MS access control management | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.10.1 Definition | Access Control allows restriction of call access attempts. All mobile stations are assigned to a "low order class", and optionally (for priority uses) also to one or more "high order classes".
A "high order class" is only valid in the HPLMN or HPLMN country. Otherwise, the "low order class" is used.
The classes are pro... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.10.2 Conformance requirement | 1. The ME shall read the access control value as part of the SIM/ME initialization procedure, and subsequently adopt this value.
3GPP TS 11.11, subclause 11.2.1.
2. If the MS is a member of at least one access class which corresponds to the permitted classes as signalled over the air interface, and the access class is ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 27.10.3 Test purpose | 1) To verify that the ME reads the access control value as part of the SIM/ME initialization procedure, and subsequently adopts this value.
2) To verify that the MS controls its network access in accordance with its access control class and the conditions imposed by the serving network.
3) For PCS 1 900: To verify the ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.