text stringlengths 78 3.17k |
|---|
<｜begin▁of▁sentence｜>
### Instruction:
FABRICQ_MGR-7-ERR_SYSDB_EDM_REG
### Response:
(Severity: 7), (Category: FABRIC), (Description: Fabricq Sysdb Register EDM error), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative... |
<｜begin▁of▁sentence｜>
### Instruction:
PLIM_ASIC-3-IMDR_ERR
### Response:
(Severity: 3), (Category: L2), (Description: Plim asic driver imdr errors. Typically these errors indicate failure in system services during the imdr procedure.), (Recommended Action: Check whether process 'plaspa_server' is up and running. Check... |
<｜begin▁of▁sentence｜>
### Instruction:
OSPF-3-BGPLS_MEM_SHUT
### Response:
(Severity: 3), (Category: ROUTING), (Description: The router or OSPF process is experiencing low memory condition. As a setup to stabilizing system, the BGP-LS feature is first being disabled so as to recover memory for OSPF and system to be abl... |
<｜begin▁of▁sentence｜>
### Instruction:
CROSSBAR-1-IN_BUF_CRC_ERROR_LNK3
### Response:
(Severity: 1), (Category: PLATFORM), (Description: Crossbar driver detected excessive input buffer CRC error on link 3), (Recommended Action: If this alarm persists for a period of 60 seconds after all the cards are in IOS-XR RUN stat... |
<｜begin▁of▁sentence｜>
### Instruction:
LDA-4-OVERSUBSCRIPTION
### Response:
(Severity: 4), (Category: PLATFORM), (Description: A warning about an over subscription of ports . The warning message describes that this particular NP is over subscribed.), (Recommended Action: The warning is not critical.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
MPLS_LSD-3-ERR_IPC_SEND
### Response:
(Severity: 3), (Category: ROUTING), (Description: AIPC ipc_sendv returns an unexpected error other than flow control.), (Recommended Action: AIPC return unexpected ERROR code. A chance of losing lsd information. Please collect show tech for mp... |
<｜begin▁of▁sentence｜>
### Instruction:
INSTMGR-6-INSTALL_LOAD_PHASE_STARTED
### Response:
(Severity: 6), (Category: INSTALL), (Description: The load phase of an ISSU operation has started - another message will be output when the phase finishes.), (Recommended Action: No action is required.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
CIH-3-ASIC_ERROR_SHUTDOWN_LINK_FABRIC
### Response:
(Severity: 3), (Category: PLATFORM), (Description: An ASIC error has occured and cause fabric link shutdown.), (Recommended Action: An error that causes fabric link shutdown has happened and been handled *None*)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
PIM_MA-3-ERR
### Response:
(Severity: 3), (Category: ROUTING), (Description: Internal error.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide... |
<｜begin▁of▁sentence｜>
### Instruction:
XTC-5-SR_POLICY_BFD_SESSION_STATE_CHANGE
### Response:
(Severity: 5), (Category: OS), (Description: BFD session state has changed for a particular LSP.), (Recommended Action: If the session state is down, then it means that dataplane may be dropping traffic. If the session state i... |
<｜begin▁of▁sentence｜>
### Instruction:
BRIDGE-2-XAUI_1_LQ_OFLOW_1
### Response:
(Severity: 2), (Category: PLATFORM), (Description: Queue overflow error on XAUI 1 LQ on bridge instance-1.), (Recommended Action: If the error persists, please reload the board using the command 'hw-module location <> reload'. If the messag... |
<｜begin▁of▁sentence｜>
### Instruction:
CFM-6-EFD_CHANGE
### Response:
(Severity: 6), (Category: L2), (Description: An interface was shut down or brought up by a local MEP after a fault condition was detected or cleared. The action is taken because the service to which the local MEP belongs has EFD configured; this mess... |
<｜begin▁of▁sentence｜>
### Instruction:
KIM-3-ADD_CONNECTED_ROUTE_FAIL
### Response:
(Severity: 3), (Category: INFRA), (Description: A failure occurred when attempting to create a connected route in the TPA system for the specified vrf interface. Forwarding for TPA applications (including telemetry) will likely be impac... |
<｜begin▁of▁sentence｜>
### Instruction:
OIRD-7-TIMER_INIT_FAIL
### Response:
(Severity: 7), (Category: PLATFORM), (Description: Failed to init timer events.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provid... |
<｜begin▁of▁sentence｜>
### Instruction:
FSYNC-6-SSM_EEEC
### Response:
(Severity: 6), (Category: L2), (Description: The quality level of the source has been changed to or from EEEC.), (Recommended Action: None, this is an informational condition that does not require troubleshooting.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
INTF_MGBL-7-INIT_FAILED
### Response:
(Severity: 7), (Category: PKT_INFRA), (Description: The process failed to initialise and will exit.), (Recommended Action: The process will be restarted automatically. If the error happens repeatedly then contact support. Copy the error messag... |
<｜begin▁of▁sentence｜>
### Instruction:
TACACSD-3-BAGS_UNREG_ERR
### Response:
(Severity: 3), (Category: SECURITY), (Description: An internal software error occurred.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative ... |
<｜begin▁of▁sentence｜>
### Instruction:
OSPFv3_UV-3-ERR_SYSDB_CONNECT
### Response:
(Severity: 3), (Category: ROUTING), (Description: The ospfv3_uv process was unable to bind to SysDB.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical suppo... |
<｜begin▁of▁sentence｜>
### Instruction:
HBAGENT-4-SET_THREAD_NEW_PRIORITY
### Response:
(Severity: 4), (Category: PLATFORM), (Description: Unable to set the heartbeat pulse of this node to high priority. Proceeding with default priority, however in a high CPU consumption, this node's heartbeat pulse may get lost, causin... |
<｜begin▁of▁sentence｜>
### Instruction:
CT_DSP-1-ALARM_OPTICS_GLOBAL_ALARM
### Response:
(Severity: 1), (Category: PLATFORM), (Description: '.'), (Recommended Action: --)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
CROSSBAR-1-LOW_OUT_MEM_UCORR_ECC_ERROR_LNK2
### Response:
(Severity: 1), (Category: PLATFORM), (Description: Crossbar driver detected multicast output memory uncorrectable ECC error on link 2), (Recommended Action: If this alarm persists for a period of 60 seconds after all the ca... |
<｜begin▁of▁sentence｜>
### Instruction:
CFP-3-LANE_1_HIGH_TX_POWER_WARNING
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Environmental monitoring has detected a CFP Tx power greater than or equal to the high Tx power warning threshold. The CFP is the pluggable optics on the line cards. The Tx power th... |
<｜begin▁of▁sentence｜>
### Instruction:
FIA-3-ERR_ECM_CREATE
### Response:
(Severity: 3), (Category: FABRIC), (Description: The FIA driver encountered an event connection manager error. The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times the error is encountered, to... |
<｜begin▁of▁sentence｜>
### Instruction:
SHELFMGR_HAL-3-POWER_FEED_REDUNDANCY
### Response:
(Severity: 3), (Category: PLATFORM), (Description: The router will have insufficient power to sustain traffic in the event of an AC power feed failure.), (Recommended Action: - Please collect the following CLI command to determine... |
<｜begin▁of▁sentence｜>
### Instruction:
FIA-1-SKT_NI_INTR_BA_STALLED_0
### Response:
(Severity: 1), (Category: FABRIC), (Description: SKT_NI_INTR_BA_STALLED interrupt on FIA), (Recommended Action: Wait a few minutes. If it doesn't recover, please reload the board using command 'reload location <>'. Make sure board is se... |
<｜begin▁of▁sentence｜>
### Instruction:
PLAT_CLIENT-2-SIA_EXPIRE_CLOCK_CHANGE
### Response:
(Severity: 2), (Category: LICENSE), (Description: SIA Grace period will expire if clock is set back in time for more than 24 hours.), (Recommended Action: Register the device to Cisco CSSM Server and rectify SIA OOC)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
MRIB_API-7-ASYNC_WAR
### Response:
(Severity: 7), (Category: ROUTING), (Description: 'A recoverable error condition occurred in the MRIB API'), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support ... |
<｜begin▁of▁sentence｜>
### Instruction:
PA-6-INFO_GENERAL
### Response:
(Severity: 6), (Category: OS), (Description: The PA encountered some problem in genric nature or plain information.), (Recommended Action: Restarting lpts_pa may fix the issue.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
LS_PRM-3-SHMWIN_ERR
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Operation on the shared memory window encountered the error.), (Recommended Action: Please collect output of the following commands: show platform show log show process blocked location <> show sh... |
<｜begin▁of▁sentence｜>
### Instruction:
AMT-3-NET_ERR
### Response:
(Severity: 3), (Category: ROUTING), (Description: Internal error.), (Recommended Action: --)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
PINGMIB-3-NOTHREADCREATE
### Response:
(Severity: 3), (Category: SNMP), (Description: A software error occured when the ping mib process try to create a PING request processing thread), (Recommended Action: The process will attempt to recover from this situation by exit. If this m... |
<｜begin▁of▁sentence｜>
### Instruction:
LTRACE_SDT_SHOW-7-EXTEND_FAIL
### Response:
(Severity: 7), (Category: OS), (Description: The show decode helper library attempted to extend its database of decode trace string data and was unable to do so. Any trace using this string may not be printable.), (Recommended Action: Co... |
<｜begin▁of▁sentence｜>
### Instruction:
PAK-7-EXCEPTION_LITE
### Response:
(Severity: 7), (Category: PKT_INFRA), (Description: An software exception had occurred in the packet manager library. The client process terminated with exit code -1. The reason is that the client passed an invalid packet to packet manager librar... |
<｜begin▁of▁sentence｜>
### Instruction:
SI-3-SD_FAIL
### Response:
(Severity: 3), (Category: SERVICES), (Description: And API call to service director failed. Details of the operation are part of the error message. This may impact service bringup on the configured location.), (Recommended Action: This may prevent functi... |
<｜begin▁of▁sentence｜>
### Instruction:
EGRESSQ_HW_DLL-3-RLDRAM_BIST_FAILURE
### Response:
(Severity: 3), (Category: L2), (Description: Egress queueing ASIC encountered a failure when doing BIST testing on its external Redunced-Latency-DRAM (RLDRAM). Possible cause for this error condition is a faulty hardware.), (Recom... |
<｜begin▁of▁sentence｜>
### Instruction:
CONFIGCLI-3-FILE_OPERATION
### Response:
(Severity: 3), (Category: MGBL), (Description: config process failed to perform a file operation due to either filesystem restart/busy or an internal error.), (Recommended Action: This error could happen when config process can not perform ... |
<｜begin▁of▁sentence｜>
### Instruction:
HA_WD-3-OPEN_PROCFS
### Response:
(Severity: 3), (Category: HA), (Description: Failed to open procfs file or directory.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and pro... |
<｜begin▁of▁sentence｜>
### Instruction:
SYSLOG-5-LOG_NOTICE
### Response:
(Severity: 5), (Category: OS), (Description: A Notice message logged.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the represe... |
<｜begin▁of▁sentence｜>
### Instruction:
PCIER-2-PCIE_FC_ENUM_ERR
### Response:
(Severity: 2), (Category: PLATFORM), (Description: A PCIE enumeration error was detected for this Fabric Card. The error prevents this card to do traffic switching thereby making it unusable), (Recommended Action: Please correct the problem b... |
<｜begin▁of▁sentence｜>
### Instruction:
INSTALL-6-RP_SWITCHOVER
### Response:
(Severity: 6), (Category: INFRA), (Description: An RP switchover has occurred during an install operation. The formerly active RP will be removed from the install operation, and will remain out of service until the install transaction is compl... |
<｜begin▁of▁sentence｜>
### Instruction:
CFM-4-NOTIFY_BNM_FAILED
### Response:
(Severity: 4), (Category: L2), (Description: The CFM packet handling module has detected that there is a new BNM link, a bandwidth change on a BNM link, or the periodic timer has expired but has failed to notify the management module. As a res... |
<｜begin▁of▁sentence｜>
### Instruction:
OSPFv3_UV-3-ERR_MEM_ALLOC_FAIL
### Response:
(Severity: 3), (Category: ROUTING), (Description: The ospfv3_uv process was unable to allocate memory for the specified resource.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, c... |
<｜begin▁of▁sentence｜>
### Instruction:
OT-3-LIB_INIT_FAIL
### Response:
(Severity: 3), (Category: SERVICES), (Description: An initialization routine from a dynamically loaded library failed.), (Recommended Action: 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technic... |
<｜begin▁of▁sentence｜>
### Instruction:
INBAR_HB_TOPAZ-4-LTRACE_INIT_FAIL
### Response:
(Severity: 4), (Category: FABRIC), (Description: ltrace initialization failed.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative ... |
<｜begin▁of▁sentence｜>
### Instruction:
FIA-1-PKT_INT_ERR_AT_DDRIF_0_1
### Response:
(Severity: 1), (Category: FABRIC), (Description: Packet Integrity Error at DDR interface from Punt/Bridge-0 FPGA on FIA 0.), (Recommended Action: Verify correct version of Punt/Bridge FPGA is loaded. If the message recurs, copy the erro... |
<｜begin▁of▁sentence｜>
### Instruction:
RPL_COORD-7-DBGINIT
### Response:
(Severity: 7), (Category: ROUTING), (Description: The rpl multi-version coordinator was unable to setup the debug handlers. This will not affect its operational, but will prevent debug commands for the coordinator from functioning.), (Recommended ... |
<｜begin▁of▁sentence｜>
### Instruction:
MPLS_LSD-3-ERR_IPC_BAD_MSG
### Response:
(Severity: 3), (Category: ROUTING), (Description: LSD received a message with bad size or bad version.), (Recommended Action: Please collect show tech for mpls_lsd and aipc for further investigation.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
STANDBY-3-ERR_REGISTER
### Response:
(Severity: 3), (Category: IP), (Description: Registration for an IOSXR service failed during HSRP's operation. This may indicate a connection failure with the IOSXR service as indicated in the error message.), (Recommended Action: Restart the H... |
<｜begin▁of▁sentence｜>
### Instruction:
ISIS-5-AUTH_VERIFY_FAILED
### Response:
(Severity: 5), (Category: ROUTING), (Description: The process encountered an error when verifying the authentication digest. This may be due to misconfiguration on the local or remote system. It is possible that no currently valid keys are a... |
<｜begin▁of▁sentence｜>
### Instruction:
PWRMON-1-IDPROM_INVALID
### Response:
(Severity: 1), (Category: PLATFORM), (Description: 'The IDPROM may be corrupted.'), (Recommended Action: Try restarting the using CLI command in exec mode - process restart pwr_mgmt If the error exists try -insert and re-insert the PM If the e... |
<｜begin▁of▁sentence｜>
### Instruction:
SAM-4-WARNING_CSS_CERTIFICATE_EXPIRED
### Response:
(Severity: 4), (Category: SECURITY), (Description: SAM found the expired CSS certificate in table had been accepted by user.), (Recommended Action: 'Copy the error message exactly as it appears on the console or in the system log... |
<｜begin▁of▁sentence｜>
### Instruction:
T3E3-4-LOOPSTATUS
### Response:
(Severity: 4), (Category: L2), (Description: A configurable controller loopback status.), (Recommended Action: No action reqiured. Msg displays loop status)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
MVRP-4-MAD_INIT_FAILED
### Response:
(Severity: 4), (Category: L2), (Description: The MVRP IO process has failed to reinitialise with the MAD following a change in bridging configuration. Periodic retries will occur to successfully reinitialise with the MAD. Until the MAD is initi... |
<｜begin▁of▁sentence｜>
### Instruction:
LIBNOTIFY-7-PARAMETER_MISSING_OR_NULL
### Response:
(Severity: 7), (Category: INSTALL), (Description: An invalid parameter has been unexpectedly passed to the Install infrastructure. This is a coding error. The current request or operation will not be completed.), (Recommended Act... |
<｜begin▁of▁sentence｜>
### Instruction:
How to display rollback changes in Cisco IOS XR?
### Response:
To display the changes that will be rolled back, use the 'show configuration rollback changes' command. RP/0/RSP0/CPU0:router#show configuration rollback changes
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
CPA_INTF_WDMON-3-ERROR
### Response:
(Severity: 3), (Category: PLATFORM), (Description: This message indicates that a failure has occured in the CPA interface), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco t... |
<｜begin▁of▁sentence｜>
### Instruction:
AAA-3-LIB_UTIL_ERROR_NO_MEM
### Response:
(Severity: 3), (Category: SECURITY), (Description: Failed to allocate memory.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and pro... |
<｜begin▁of▁sentence｜>
### Instruction:
PEXRC-2-WARN_INIT
### Response:
(Severity: 2), (Category: PLATFORM), (Description: The message can be displayed whenever there is a driver initialization error.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco... |
<｜begin▁of▁sentence｜>
### Instruction:
RSPP_MA-3-EVENT
### Response:
(Severity: 3), (Category: SERVICES), (Description: An error occured receiving an event from the OS. The process will restart.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system lo... |
<｜begin▁of▁sentence｜>
### Instruction:
HFR_L2FIB_METRO_SHOW-3-INVALID_ARG_TYPE
### Response:
(Severity: 3), (Category: PLATFORM), (Description: HFR_L2FIB_METRO_SHOW has encountered an init or a sysdb error.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call you... |
<｜begin▁of▁sentence｜>
### Instruction:
INST_IO-7-DEVICE_FULL
### Response:
(Severity: 7), (Category: INSTALL), (Description: An attempt to open or write to a file on the specified device failed because the device had insufficient free space. The node may be in an inconsistent state due to a missing or truncated file; c... |
<｜begin▁of▁sentence｜>
### Instruction:
LICMGR-4-NO_OPERATION_ID
### Response:
(Severity: 4), (Category: LICENSE), (Description: The license manager encountered an error while attempting to read the license operation ID. Without a valid license operation ID the license manager will not be able to support licenses locked... |
<｜begin▁of▁sentence｜>
### Instruction:
MSDP-3-INIT_FAILED
### Response:
(Severity: 3), (Category: ROUTING), (Description: An unrecoverable error occurred at system initialization.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log. Issue the <CmdBold>show processes m... |
<｜begin▁of▁sentence｜>
### Instruction:
FIA-1-PKT_INT_ERR_AT_DDRIF_1_0
### Response:
(Severity: 1), (Category: FABRIC), (Description: Packet Integrity Error at DDR interface from Punt/Bridge-1 FPGA on FIA), (Recommended Action: Verify correct version of Punt/Bridge FPGA is loaded. If the message recurs, copy the error m... |
<｜begin▁of▁sentence｜>
### Instruction:
DUMPER-7-KERNEL_INFO_MMAP_FAILURE
### Response:
(Severity: 7), (Category: OS), (Description: Space might not have been allocated for storing kernel dump information), (Recommended Action: Please contact support with the following data. 1. show exception 2. admin show exception tra... |
<｜begin▁of▁sentence｜>
### Instruction:
LPTS_PA_FF_CL-7-DEBUG_INIT_EVENT
### Response:
(Severity: 7), (Category: OS), (Description: An error was returned when calling the debug_init_event() function.), (Recommended Action: Restarting lpts_pa may fix the issue.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
FIA-1-OOB_FC_1_ERROR_ALERT
### Response:
(Severity: 1), (Category: FABRIC), (Description: Out Of Band flow control error detected for SPAUI-1 on FIA instance, traffic would be impacted.), (Recommended Action: Please reload the board in the next maintenance window. If this fault ha... |
<｜begin▁of▁sentence｜>
### Instruction:
NP-0-SYSDB_CONFIG_TIMEOUT
### Response:
(Severity: 0), (Category: PLATFORM), (Description: Unable to retrieve configuration information from sysdb. The linecard will be reloaded.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system lo... |
<｜begin▁of▁sentence｜>
### Instruction:
FCA-2-XFP_I2C_ERROR
### Response:
(Severity: 2), (Category: PLATFORM), (Description: Port controller driver detected I2C access error on XFP port.), (Recommended Action: Ensure that the XFP plugged in is supported. If not, please replace the XFP. If the problem persists, please OI... |
<｜begin▁of▁sentence｜>
### Instruction:
PFDIAGBASE-3-CHKSUM_ERROR
### Response:
(Severity: 3), (Category: DIAG), (Description: Diagnostics detected a software error computing the checksum of a recieved packet. This is not a service impacting error.), (Recommended Action: Another software component will attempt to fix th... |
<｜begin▁of▁sentence｜>
### Instruction:
INBAR_HB-3-FGID_ERR
### Response:
(Severity: 3), (Category: FABRIC), (Description: Inbar HB running on context node failed to unregister itself with the FGID Controller while node is going down.), (Recommended Action: Copy the error message exactly as it appears on the console or ... |
<｜begin▁of▁sentence｜>
### Instruction:
sse_qosrm-3-MUTEX_DESTROY_ERROR
### Response:
(Severity: 3), (Category: PKT_INFRA), (Description: Failed to create the mutex.), (Recommended Action: Restart the process to recover from the issue.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
DUMPER-5-TIMEOUT
### Response:
(Severity: 5), (Category: OS), (Description: dumper restarted due to watchdog timeout.), (Recommended Action: No action required. Ignore.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
CFP-2-LANE_5_HIGH_BIAS_ALARM
### Response:
(Severity: 2), (Category: PLATFORM), (Description: Environmental monitoring has detected a CFP laser bias greater than or equal to the high laser bias alarm threshold. The CFP is the pluggable optics on the line cards. The laser bias thre... |
<｜begin▁of▁sentence｜>
### Instruction:
ISIS-4-INTF_PROTECT_INFRA_UPDATE
### Response:
(Severity: 4), (Category: ROUTING), (Description: IS-IS failed to register or unregister with protect infrastructure for high priority link-down notifications on the specified interface. IS-IS will still react to regular link-down eve... |
<｜begin▁of▁sentence｜>
### Instruction:
IPV4_MA-3-EVM_ATTACH_FAILED
### Response:
(Severity: 3), (Category: IP), (Description: The IPv4 MA process could not register the handler for the indicated event. This can happen when the process is (re)starting. The process recovers by restarting itself. If the error message does... |
<｜begin▁of▁sentence｜>
### Instruction:
SSHD_CONF_PRX-3-ERR_SYSDB_BIND
### Response:
(Severity: 3), (Category: SECURITY), (Description: Internal error.), (Recommended Action: 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide th... |
<｜begin▁of▁sentence｜>
### Instruction:
SLICE_MGR_PROXY-3-SHMWIN_ERROR
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Initialization of shared memory window failed), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support ... |
<｜begin▁of▁sentence｜>
### Instruction:
PLAT_CLIENT-2-SIA_LICENSE_PENDING_STATE
### Response:
(Severity: 2), (Category: LICENSE), (Description: SIA License status couldn't be obtained.), (Recommended Action: The customer should check the connection to the backend Smart Licensing server.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
VLANIFMIB-4-MIBLIB
### Response:
(Severity: 4), (Category: SNMP), (Description: The VLAN Interface table relationship MIB encountered an internal error. It is likely that an SNMP query that was in progress will not have been completed.), (Recommended Action: Retry the operation th... |
<｜begin▁of▁sentence｜>
### Instruction:
NPU_CFG-3-ERR_EVM_CREATE
### Response:
(Severity: 3), (Category: FABRIC), (Description: The npu config (npu_cfg) failed to create an event manager during the initialization. The driver will be non-operational due to this error.), (Recommended Action: The npu_cfg will recover by re... |
<｜begin▁of▁sentence｜>
### Instruction:
DRP_REDDRV-3-ERR_RMF_REGISTER
### Response:
(Severity: 3), (Category: PLATFORM), (Description: RMF registraton got failed as reply status is not ok. Please refer the reply status for more detail.), (Recommended Action: *SUPPORT*)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
RSP_CPUCTRL-3-SAC0_ECTW_RD_PERR
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Error reported by the cpu control fpga), (Recommended Action: Check and upgrade FPGAs on the board.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
DUMPER-7-EVM_FILE_ATTACH_FAIL
### Response:
(Severity: 7), (Category: OS), (Description: Dumper uses resource manager for various resons. Unexpected failure to attach pathname to the process might cause problem in the core dumping scenario.), (Recommended Action: Collect the follo... |
<｜begin▁of▁sentence｜>
### Instruction:
SYSDB-4-SC_WRLOCK
### Response:
(Severity: 4), (Category: SYSDB), (Description: An error occurred invoking a SysDB function. The details are in the error string.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the sys... |
<｜begin▁of▁sentence｜>
### Instruction:
QSFP_PLUS-3-LANE_1_LOW_RX_POWER_WARNING
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Environmental monitoring has detected a QSFP+ Rx power less than or equal to the low Rx power warning threshold. The QSFP+ is the pluggable optics on the line cards. The Rx pow... |
<｜begin▁of▁sentence｜>
### Instruction:
SHELFMGR-3-BOARD_NOT_SUPPORTED_ONSLOT
### Response:
(Severity: 3), (Category: PLATFORM), (Description: This message indicates that the node is being shutdown because it is not supported on the specified CRS platform.), (Recommended Action: Remove the unsupported board and replace ... |
<｜begin▁of▁sentence｜>
### Instruction:
PLAT_L2FIB_DEBUG-7-REGISTER_FAILED
### Response:
(Severity: 7), (Category: PLATFORM), (Description: Failed to initialize the debugging module in the platform L2FIB component.), (Recommended Action: None, platform software will correct itself if this happens.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
CIH-3-COMMON_ERROR
### Response:
(Severity: 3), (Category: PLATFORM), (Description: The CIH library encountered an error related to memory or data value.), (Recommended Action: An error would be reported to the client application which should handle this condition appropriately. *... |
<｜begin▁of▁sentence｜>
### Instruction:
SSHD-3-ERR_SYSDB_UNPACK
### Response:
(Severity: 3), (Category: SECURITY), (Description: Internal error.), (Recommended Action: 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the repre... |
<｜begin▁of▁sentence｜>
### Instruction:
FABRICQ-4-FI_TOPOLOGY
### Response:
(Severity: 4), (Category: FABRIC), (Description: An inconsistency between the expected and observed topologies of the fabric was detected.), (Recommended Action: *SUPPORT*)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
IPV4_MRIB-3-EXIT_ERR
### Response:
(Severity: 3), (Category: ROUTING), (Description: An unrecoverable error occurred at system initialization time.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call ... |
<｜begin▁of▁sentence｜>
### Instruction:
SLC-5-NSF_START
### Response:
None
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
CIH-1-ASIC_ERROR_PERSIST_SCRUB_THRESH
### Response:
(Severity: 1), (Category: PLATFORM), (Description: ASIC errors have occured and need memory scrubbing, such errors have crossed threshold.), (Recommended Action: Errors have been handled. *None*)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
OPTICS-6-OIR_INFO
### Response:
(Severity: 6), (Category: DRIVER), (Description: Optics driver module oir detecred.Insertion/Removal of Optics.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical suppor... |
<｜begin▁of▁sentence｜>
### Instruction:
CPAK-3-LANE_4_LOW_RX_POWER_WARNING
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Environmental monitoring has detected a CPAK Rx power less than or equal to the low Rx power warning threshold. The CPAK is the pluggable optics on the line cards. The Rx power thre... |
<｜begin▁of▁sentence｜>
### Instruction:
METRO_STATS-7-ERR_MEM
### Response:
(Severity: 7), (Category: L2), (Description: An error occurred in Hardware Stats Manager during shared memory operations. This may be because the system is running low on memory. The types of errors are: 1 Cannot open/reset/close shared memory w... |
<｜begin▁of▁sentence｜>
### Instruction:
What is the BGP route refresh capability?
### Response:
The BGP route refresh capability allows a router to dynamically request a re-advertisement of routes from a neighbor. This eliminates the need to store received routes as with soft reconfiguration. It is enabled by default if... |
<｜begin▁of▁sentence｜>
### Instruction:
HA_EEM-0-ACTION_SYSLOG_LOG_EMERG
### Response:
(Severity: 0), (Category: HA), (Description: The action_syslog call from tcl script.), (Recommended Action: Please verify command(s) mentioned in tcl script prior to error message are working fine (on router prompt). If issue is still... |
<｜begin▁of▁sentence｜>
### Instruction:
CT_DSP-1-ALARM_LOS_PORTR1
### Response:
(Severity: 1), (Category: PLATFORM), (Description: 'Tx CAUI LOS'), (Recommended Action: Check/replace cable. Check/replace optics module.)
<|EOT|>
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.