text stringlengths 78 3.17k |
|---|
<｜begin▁of▁sentence｜>
### Instruction:
NVGEN-3-INVALIDINPUT
### Response:
(Severity: 3), (Category: MGBL), (Description: 'The input is invalid. The calling function and the command are displayed'), (Recommended Action: *SH_TECH*)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
INGRESSQ-7-ERR_CLIENT_REG
### Response:
(Severity: 7), (Category: FABRIC), (Description: Ingressq client failed to Register/Unregister with Ingressq Server process. This error is also detected from the client's side. Retrial attempts would be made by the client.), (Recommended Act... |
<｜begin▁of▁sentence｜>
### Instruction:
FIA-1-SKT_SMC1_INTR_DISP_ERROR_LANE_INDICATE_15_0
### Response:
(Severity: 1), (Category: FABRIC), (Description: SKT_SMC1_INTR_DISP_ERROR_LANE_INDICATE_15 interrupt on FIA), (Recommended Action: Wait a few minutes. If it doesn't recover, please reload the board using command 'relo... |
<｜begin▁of▁sentence｜>
### Instruction:
SYS-3-MMAPSHIFT
### Response:
(Severity: 3), (Category: MGBL), (Description: The packet subsystem was not able to initialize memory.), (Recommended Action: The router will not start properly with this condition.\n' 'Call your technical support representative for assistance.)
<|EOT... |
<｜begin▁of▁sentence｜>
### Instruction:
UCP_LCTRL-7-ERR_INIT_SERVER
### Response:
(Severity: 7), (Category: ROUTING), (Description: The ucp lctrl server could not be initialized.), (Recommended Action: No action is required.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
IMUX-1-RX_MTA_FRM_LEN_ERR
### Response:
(Severity: 1), (Category: PLATFORM), (Description: Ingress MUX encountered Rx serdes lane metaframe length error.), (Recommended Action: This fault would result in traffic loss. Ensure the ingress MUX FPGA version is latest. Reload the card ... |
<｜begin▁of▁sentence｜>
### Instruction:
BPE-7-ERR_LWM_REPLY
### Response:
(Severity: 7), (Category: PLATFORM), (Description: bpe LWM reply error), (Recommended Action: Please attempt to correct the error by restarting the process by issuing the command in exec mode -process restart bpe If the message recurs, copy the er... |
<｜begin▁of▁sentence｜>
### Instruction:
What is the function of the 'install rollback' command in Cisco IOS XR?
### Response:
The 'install rollback' command in Cisco IOS XR is used to revert the router's software to a previous committed state, useful for undoing changes that may have caused issues.
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
What are the different types of OSPF LSAs and their functions?
### Response:
The main types of OSPF LSAs are\n- Type 1 Router LSA (lists all router's links/states in an area)\n- Type 2 Network LSA (generated by DR, lists all routers on a segment)\n- Type 3/4 Summary LSA (generated... |
<｜begin▁of▁sentence｜>
### Instruction:
INTCTRL-3-ERR_INIT
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Interrupt controller Driver encountered a fatal error and is not able to recover.), (Recommended Action: Please attempt to correct the error by restarting the process. Issue the command in exec mod... |
<｜begin▁of▁sentence｜>
### Instruction:
BCDLPROD-3-MSG_SEND_FAIL
### Response:
(Severity: 3), (Category: OS), (Description: A call to function for sending BCDL msg to consumers failed. This could lead to inconsistency between BCDL producers and consumers.), (Recommended Action: Contact support.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
FSDB-1-ERR_PLANE_CONFIG
### Response:
(Severity: 1), (Category: FABRIC), (Description: The fabric plane configuration for this multi-chassis system cannot be implemented with the hardware that has been discovered. This error may cause one or more fabric planes to stay down which w... |
<｜begin▁of▁sentence｜>
### Instruction:
What is the purpose of the 'allocate global' sub-command under 'mpls label range'?
### Response:
The 'allocate global' sub-command is used to allocate labels from the global label pool. By default, IOS XR uses per-interface label space. The 'allocate global' command switches the l... |
<｜begin▁of▁sentence｜>
### Instruction:
FGID_SVR-4-WARNING_INTERNAL_SW
### Response:
(Severity: 4), (Category: FABRIC), (Description: The FGID Server encountered the annunciated SW error.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call ... |
<｜begin▁of▁sentence｜>
### Instruction:
LICMGR-4-AUDIT_PROBLEM
### Response:
(Severity: 4), (Category: LICENSE), (Description: The license manager encountered a problem during an internal audit. Check the error string to determine what has happened.), (Recommended Action: Copy the error message exactly as it appears on ... |
<｜begin▁of▁sentence｜>
### Instruction:
PIM-3-ERR_MEM_ALLOC
### Response:
(Severity: 3), (Category: ROUTING), (Description: Error in allocating memory.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support represe... |
<｜begin▁of▁sentence｜>
### Instruction:
NP-0-ALL_NPS_FAILED
### Response:
(Severity: 0), (Category: PLATFORM), (Description: 'All active NPs on the line card have non-recoverable failures. The line card is no longer operational and will be reloaded.'), (Recommended Action: Copy the error message exactly as it appears on... |
<｜begin▁of▁sentence｜>
### Instruction:
CFM-5-SATELLITE_PORT_MESSAGE_RECEIVED
### Response:
(Severity: 5), (Category: L2), (Description: A notification message has been received from a Satellite regarding the operational status of CFM on Satellite fabric links.), (Recommended Action: Depending on the content of the noti... |
<｜begin▁of▁sentence｜>
### Instruction:
FIB_IPV6-3-WARNING
### Response:
(Severity: 3), (Category: L2), (Description: A runtime error occurred in ASR9K IPv6 FIB module. The reason for the failure is also displayed. Please call Cisco Support with the error information.), (Recommended Action: Please collect the console lo... |
<｜begin▁of▁sentence｜>
### Instruction:
PLATFORM_LPTS_PIFIB-7-ERR_CONN_INIT
### Response:
(Severity: 7), (Category: OS), (Description: An internal error was detected when trying to connect to the respective component.), (Recommended Action: When this issue happens, it will trigger an automatic restart. Check the status ... |
<｜begin▁of▁sentence｜>
### Instruction:
MPLS_MCAST-2-ERR_DLL_INIT
### Response:
(Severity: 2), (Category: PLATFORM), (Description: A failure occurred during the initialization of the mpls mcast platform ingress netio DLL.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the c... |
<｜begin▁of▁sentence｜>
### Instruction:
CONFIG-3-UNLOCK_ERR
### Response:
(Severity: 3), (Category: MGBL), (Description: An error was encountered during deletion of the configuration lock. This configuration operation (e.g. save/restore configuration, CLI commit) is successful, but subsequent configuration operations co... |
<｜begin▁of▁sentence｜>
### Instruction:
CLKCTRL-3-RX_ALARM_FRAME_ERR
### Response:
(Severity: 3), (Category: PLATFORM), (Description: For UTI mode alarm is raised if frame error rate exceeds 2%.), (Recommended Action: 1) Ensure valid BITS/UTI signal is applied at input port.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
FIA-1-SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8_0
### Response:
(Severity: 1), (Category: FABRIC), (Description: SKT_SMC0_INTR_ALIGN_ERROR_LANE_INDICATE_8 interrupt on FIA), (Recommended Action: Wait a few minutes. If it doesn't recover, please reload the board using command 'relo... |
<｜begin▁of▁sentence｜>
### Instruction:
SNMP-3-TARGETNONE
### Response:
(Severity: 3), (Category: SNMP), (Description: A configuration command refers to an SNMP target that has not yet been configured.), (Recommended Action: You must configure an SNMP target before you can refer to it. Examine your configuration. Ensure... |
<｜begin▁of▁sentence｜>
### Instruction:
IFMGR-3-MISSING_RULES
### Response:
(Severity: 3), (Category: PKT_INFRA), (Description: IM is unable to create an interface/caps due to static information about the resource type being missing. The system may be in an inconsistent state.), (Recommended Action: Copy the error messa... |
<｜begin▁of▁sentence｜>
### Instruction:
OSPFv3-3-PKTDROP_STR
### Response:
(Severity: 3), (Category: ROUTING), (Description: An input packet was dropped for the specified reason.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support rep... |
<｜begin▁of▁sentence｜>
### Instruction:
SHMWIN-6-FILE_EXISTS
### Response:
(Severity: 6), (Category: OS), (Description: SHMWIN encountered an error condition, the file was existing already.), (Recommended Action: No action is required.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
NVGEN-3-LOCK_ERR
### Response:
(Severity: 3), (Category: MGBL), (Description: A lock operation on shared resource, called by nvgen failed due to the mentioned error.), (Recommended Action: Collect the output of show logging and inform Copy the error message exactly as it appears o... |
<｜begin▁of▁sentence｜>
### Instruction:
DUMPER-4-FLT_STACK
### Response:
(Severity: 4), (Category: OS), (Description: Signal info.), (Recommended Action: No action required.Ignore.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
RVM_MGR-3-ERROR
### Response:
(Severity: 3), (Category: PKT_INFRA), (Description: Error message), (Recommended Action: none.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
SCONBKUP-6-INTERNAL_INFO
### Response:
(Severity: 6), (Category: MGBL), (Description: This is a informational message indicating that cfgmgr debug logs have been collected during reload.), (Recommended Action: This is a info message. No action to be taken)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
ETHERNET_LOOPBACK-3-TRACE_INIT
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Failed to initialize trace in the platform Ethernet loopback component), (Recommended Action: No action is required.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
BRIDGE-3-NPU_1_PKT_MAXLEN_ERR_3
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Packet maximum length error on NPU-1 interface on bridge instance-3.), (Recommended Action: If the error persists, please reload the board using the command 'reload location <>'. If th... |
<｜begin▁of▁sentence｜>
### Instruction:
XCVR-3-DEBUG_INIT_FAILED
### Response:
(Severity: 3), (Category: PLATFORM), (Description: This is an informational message from the XCVR stating that failed to initialize a debug event type structure provided by the application with the supplied data), (Recommended Action: *RECUR*... |
<｜begin▁of▁sentence｜>
### Instruction:
INSTMGR_LIB-6-TEST_ISSU_RUN_RELOAD_SLEEP
### Response:
(Severity: 6), (Category: INSTALL), (Description: Informs the user how many seconds the node is sleeping before reloading during a 'test ISSU-run' operation.), (Recommended Action: No action is required.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
HFR_TUNNEL_EA-3-INIT_ERR1
### Response:
(Severity: 3), (Category: PLATFORM), (Description: This is an error message in the CRS platform specific code software to indicate errors that happened during initialisation. This error is most likely caused by a temporary situation, so is u... |
<｜begin▁of▁sentence｜>
### Instruction:
What is the function of the XML Management Interface in Cisco IOS XR?
### Response:
The XML Management Interface in Cisco IOS XR allows for the configuration and monitoring of devices using XML over secure HTTP (HTTPS), providing a standardized and programmable interface.
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
CFM-6-MEP_CHANGE
### Response:
(Severity: 6), (Category: L2), (Description: A CCM message was received from a new peer MEP, or a previously-known peer MEP timed out (i.e. its configured loss threshold was exceeded). This message appears because the service which the local MEP belo... |
<｜begin▁of▁sentence｜>
### Instruction:
MEDIAAPI-4-INVALID_PARM_FORMAT_PART
### Response:
(Severity: 4), (Category: MEDIA), (Description: An invalid parameter value was passed to the driver to format and partition the media device.), (Recommended Action: Check the syntax for the the format command Report this message to... |
<｜begin▁of▁sentence｜>
### Instruction:
How to configure inter-VRF route leaking in MPLS L3VPN?
### Response:
To configure inter-VRF route leaking in MPLS L3VPN, use import and export route-target commands between VRFs. vrf MyVRF
import route-target 65000:200
vrf MyVRF2
export route-target 65000:200
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
IMFPGA-3-SI5347_PLL_LOL
### Response:
(Severity: 3), (Category: PLATFORM), (Description: SI5347 PLL loss of lock detected/cleared for RSP), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support repr... |
<｜begin▁of▁sentence｜>
### Instruction:
RIP-3-ERR_THREAD_MUTEX_LOCK
### Response:
(Severity: 3), (Category: ROUTING), (Description: Internal error during locking of a RIP resource.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Ci... |
<｜begin▁of▁sentence｜>
### Instruction:
RSPP_MA-4-DUP_REMOVE
### Response:
(Severity: 4), (Category: SERVICES), (Description: The given attachment configuration, which was previously invalid due to duplicate attachments being configured on different interfaces, is now valid as the duplicate attachment configuration has ... |
<｜begin▁of▁sentence｜>
### Instruction:
BRIDGE-2-XAUI_1_HQ_PKT_LEN_1
### Response:
(Severity: 2), (Category: PLATFORM), (Description: Queue packet length error on XAUI 1 HQ on bridge instance-1.), (Recommended Action: If the error persists, please reload the board using the command 'hw-module location <> reload'. If the... |
<｜begin▁of▁sentence｜>
### Instruction:
SYNCFS2LIB-7-MUTEX_UNLOCK
### Response:
(Severity: 7), (Category: MEDIA), (Description: A required mutex unlock failed.), (Recommended Action: Contact customer support)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
L2SNOOP-3-INIT_ERR
### Response:
(Severity: 3), (Category: IP), (Description: An software error occurred while starting up of L2SNOOP process. If this occurred during process startup, then the process may be restarted.), (Recommended Action: The process will attempt to recover fro... |
<｜begin▁of▁sentence｜>
### Instruction:
BRIDGE-2-DEC_A_PKT_LEN_ERR_1
### Response:
(Severity: 2), (Category: PLATFORM), (Description: Packet with invalid length encountered by decoder A on bridge instance-1.), (Recommended Action: If the error persists, please reload the board using the command 'hw-module location <> re... |
<｜begin▁of▁sentence｜>
### Instruction:
ETH_LB-3-INTERNAL_PROBLEM
### Response:
(Severity: 3), (Category: L2), (Description: An internal error has occurred, causing the feature to not be able to function properly.), (Recommended Action: The process is automatically restarted. If the problem persists, Copy the error mess... |
<｜begin▁of▁sentence｜>
### Instruction:
LPTS_PREIFIB-3-REASS_LIST
### Response:
(Severity: 3), (Category: OS), (Description: The list of reassembly servers is incorrect.), (Recommended Action: Please try restarting pifibm_server_lc and pifibm_server_rp processes.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
OTN_FRAMER-3-PCI_DEV_RECOVERY_CB
### Response:
(Severity: 3), (Category: OS), (Description: pci devices recovery cb messages), (Recommended Action: Informational only.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
NVRAW_LIB-4-REBOOT_HIST
### Response:
(Severity: 4), (Category: MEDIA), (Description: Information to collect the logs), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provi... |
<｜begin▁of▁sentence｜>
### Instruction:
CPAK-3-LANE_2_LOW_TEMP_WARNING
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Environmental monitoring has detected a CPAK laser temperature less than or equal to the low temperature warning threshold. The CPAK is the pluggable optics on the line cards. The tempe... |
<｜begin▁of▁sentence｜>
### Instruction:
CDP-4-DUPLEX_MISMATCH
### Response:
(Severity: 4), (Category: L2), (Description: CDP discovered mismatching duplex configuration on neighboring interfaces.), (Recommended Action: Configure the interfaces with the same duplex (full or half).)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
RTC-2-CAL_CHIP_NOT_FOUND
### Response:
(Severity: 2), (Category: MGBL), (Description: Unable to find calendar chip.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide... |
<｜begin▁of▁sentence｜>
### Instruction:
SPM-3-ERROR_PTHREAD_INIT
### Response:
(Severity: 3), (Category: SECURITY), (Description: Internal error.), (Recommended Action: 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the repr... |
<｜begin▁of▁sentence｜>
### Instruction:
NPUXBAR_BRIDGE-1-EBS_OC_HDR_CRC_ERR
### Response:
(Severity: 1), (Category: PLATFORM), (Description: EBS from FIA header checksum error.), (Recommended Action: None.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
FHRP_OUTPUT-3-WARN_COMMS_INIT
### Response:
(Severity: 3), (Category: IP), (Description: The FHRP output process communications failed to initialize correctly. In this situation the FHRP output process retries the initialization, but may not recover if the failure to initialize pe... |
<｜begin▁of▁sentence｜>
### Instruction:
RSP_CPUCTRL-3-ARB_ECTW_RDATA_TO
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Error reported by the cpu control fpga), (Recommended Action: Check and upgrade FPGAs on the board.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
LOGIN_SHELL-6-SIGNAL_HANDLER_INFO
### Response:
(Severity: 6), (Category: MGMT), (Description: This comes when registration of signal fails due to some system issue), (Recommended Action: The work-around is restart process would resolve the issue)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
I2CCTRL-2-MASTERSHIP_DENIED
### Response:
(Severity: 2), (Category: PLATFORM), (Description: SMBus Mastership Denied by Bus-Master Mux), (Recommended Action: Please attempt to correct the error by reloading the card by issuing the command in admin mode -reload location <> If the m... |
<｜begin▁of▁sentence｜>
### Instruction:
What is the purpose of the MPLS TE FRR backup tunnel timers feature?
### Response:
The MPLS TE FRR backup tunnel timers feature allows the configuration of hold and delay timers for backup tunnels. The hold timer specifies how long a backup tunnel should remain in place after the ... |
<｜begin▁of▁sentence｜>
### Instruction:
SVII_ADJ_LIB-3-INIT_FAILED
### Response:
(Severity: 3), (Category: PKT_INFRA), (Description: The SVI Adjacency Manager Library's initialization has failed. The process will exit and automatically restart.), (Recommended Action: If the message recurs, copy the error message exactly... |
<｜begin▁of▁sentence｜>
### Instruction:
PERF_MEAS-3-CFG_PORT_FAILED_TO_OPEN
### Response:
(Severity: 3), (Category: ROUTING), (Description: After several retries, the configured port has failed to open. The first argument is the name of the configured port and the second argument is the port number.), (Recommended Actio... |
<｜begin▁of▁sentence｜>
### Instruction:
PSE-4-IMDR_RESET_FAILED
### Response:
(Severity: 4), (Category: L2), (Description: This is an error message in the PSE Driver to indicate that it failed to perform iMDR reset of specified pse instance due to the specified reason.), (Recommended Action: No action is required.)
<|EO... |
<｜begin▁of▁sentence｜>
### Instruction:
What is the purpose of OSPF areas and how do they help with scalability?
### Response:
OSPF allows a network to be divided into areas. An area is a logical collection of OSPF networks, routers, and links that have the same area identification. Areas limit the scope of link-state a... |
<｜begin▁of▁sentence｜>
### Instruction:
SHELFMGRV2-4-CARD_POST_NOT_TRIGGER
### Response:
(Severity: 4), (Category: PLATFORM), (Description: The card is reloaded due to a faulty HW/ASIC. The Online Diags process can't perform the required diagnostic testing on the falling device, hence the card will then be reloaded with... |
<｜begin▁of▁sentence｜>
### Instruction:
EIGRP-6-PAK_SEND
### Response:
(Severity: 6), (Category: ROUTING), (Description: Failed to send a packet. This can happen if other processes involved in packet forwarding are restarting. This may or may not be transient. If the packet which was not sent is HELLO then the EIGRP adj... |
<｜begin▁of▁sentence｜>
### Instruction:
PROCMGR-3-SYSDB_EDM_REG_ERROR
### Response:
(Severity: 3), (Category: PLATFORM), (Description: Procmgr failed to register with Sysdb EDM. This may be a program level error.), (Recommended Action: Provide the required information to support If the message recurs, copy the error mes... |
<｜begin▁of▁sentence｜>
### Instruction:
CARD-3-CPI_NOT_READY
### Response:
(Severity: 3), (Category: PLATFORM), (Description: ClkCtrl driver detected a card cpi not ready condition), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support r... |
<｜begin▁of▁sentence｜>
### Instruction:
CROSSBAR-1-HI_FPOE_DB_CORR_ECC_ERROR_LNK2
### Response:
(Severity: 1), (Category: PLATFORM), (Description: Crossbar driver detected unicast FPOE correctable ECC error on link 2), (Recommended Action: If this alarm persists for a period of 60 seconds after all the cards are in IOS-... |
<｜begin▁of▁sentence｜>
### Instruction:
VKG_IPV6_EA-3-FAILURE1
### Response:
(Severity: 3), (Category: PLATFORM), (Description: This is a failure message in the ASR9K platform specific code software to indicate anomolies that are not serious failure. This failure is most likely caused by a temporary situation, so is unl... |
<｜begin▁of▁sentence｜>
### Instruction:
FIA-1-SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5_0
### Response:
(Severity: 1), (Category: FABRIC), (Description: SKT_SMC0_INTR_OOB_ERROR_LANE_INDICATE_5 interrupt on FIA), (Recommended Action: Wait a few minutes. If it doesn't recover, please reload the board using command 'reload l... |
<｜begin▁of▁sentence｜>
### Instruction:
ARP_GMP-4-WARN_INIT
### Response:
(Severity: 4), (Category: IP), (Description: The ARP GMP process failed to initialize correctly. In this situation it restarts, but it may not recover if there is a persistant error in the IOSXR system and the ARP GMP is later unable to reestablis... |
<｜begin▁of▁sentence｜>
### Instruction:
MEMPOOL_EDM-1-SYSDB_REGISTRATION_FAILURE
### Response:
(Severity: 1), (Category: OS), (Description: Sysdb registration failure), (Recommended Action: 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative... |
<｜begin▁of▁sentence｜>
### Instruction:
OIRD-7-MMAP_FAIL
### Response:
(Severity: 7), (Category: PLATFORM), (Description: Failed to mmap OIR registers.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the... |
<｜begin▁of▁sentence｜>
### Instruction:
LPTS_PREIFIB-3-DATAPATH_CMD
### Response:
(Severity: 3), (Category: OS), (Description: The given Pre-IFIB datapath control command returns error.), (Recommended Action: Copy the error message exactly as it appears, and report it to your technical support representative. Copy the e... |
<｜begin▁of▁sentence｜>
### Instruction:
ENVMON-4-CBC_WDOG_EXCEED_THRESHOLD
### Response:
(Severity: 4), (Category: PLATFORM), (Description: Watchdog stats are collected on active RP.If watchdog toggle is not seen for long time, the message will be displayed.), (Recommended Action: Collect the output from RSP : admin sho... |
<｜begin▁of▁sentence｜>
### Instruction:
SYSDB-7-STARTUP
### Response:
(Severity: 7), (Category: SYSDB), (Description: A startup request failed during the second round of callbacks.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Ci... |
<｜begin▁of▁sentence｜>
### Instruction:
KIM-3-DEFAULT_ROUTE_CREATION_FAIL
### Response:
(Severity: 3), (Category: INFRA), (Description: A failure occurred when attempting to create a default route in the TPA system for the specified vrf. Forwarding for TPA applications (including telemetry) will likely be impacted.), (R... |
<｜begin▁of▁sentence｜>
### Instruction:
OT-6-LIB_AVAIL
### Response:
None
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
LIB_VMAN-3-INCONSISTENT_CPUTUNES_CONFIG
### Response:
(Severity: 3), (Category: OS), (Description: The virtual service machine definition file is requesting invalid CPU tunes parameter.), (Recommended Action: Use a different valid machine definition file for the virtual service. I... |
<｜begin▁of▁sentence｜>
### Instruction:
What is the purpose of the install activate auto-abort-timer command in IOS XR?
### Response:
The 'install activate auto-abort-timer' command is used to set a timer for the automatic rollback of an installation if the user doesn't commit the changes within the specified time. This... |
<｜begin▁of▁sentence｜>
### Instruction:
QSFP_PLUS-2-LANE_1_LOW_RX_POWER_ALARM
### Response:
(Severity: 2), (Category: PLATFORM), (Description: Environmental monitoring has detected a QSFP+ Rx power less than or equal to the low Rx power alarm threshold. The QSFP+ is the pluggable optics on the line cards. The Rx power t... |
<｜begin▁of▁sentence｜>
### Instruction:
NPUXBAR_BRIDGE-1-EBS_CPP_HP_FIFO_MBE
### Response:
(Severity: 1), (Category: PLATFORM), (Description: EBS to CPP high priority FIFO multiple bits error.), (Recommended Action: None.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
OFA_PLUGIN-3-BD_INVALID_LS_LAYER
### Response:
(Severity: 3), (Category: L2), (Description: Unable to assign bridge domain because logical switch is not layer2 type.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your ... |
<｜begin▁of▁sentence｜>
### Instruction:
PKG-3-CORRUPT_INSTALL_FILE
### Response:
(Severity: 3), (Category: INSTALL), (Description: An install file is corrupt. This may affect the system in a number of ways including preventing nodes from booting and preventing install operations.), (Recommended Action: First attempt to ... |
<｜begin▁of▁sentence｜>
### Instruction:
SYSDB-4-SC_FIND
### Response:
(Severity: 4), (Category: SYSDB), (Description: An error occurred invoking a SysDB function. The details are in the error string.), (Recommended Action: If the message recurs, copy the error message exactly as it appears on the console or in the syste... |
<｜begin▁of▁sentence｜>
### Instruction:
SIM_IPC-3-SYSDB_LIST_FAIL
### Response:
(Severity: 3), (Category: PLATFORM), (Description: The message indicates the failure while updating the data items in the system database.), (Recommended Action: Please collect the console log and CLI output. Copy the error message exactly a... |
<｜begin▁of▁sentence｜>
### Instruction:
ISLM-4-SESSION_THRESHOLD_EXCEEDED
### Response:
(Severity: 4), (Category: SUBSCRIBER), (Description: This syslog is printed when the configured session threshold has been exceeded.), (Recommended Action: This is warning to alert the user that sessions may be near the limit that is... |
<｜begin▁of▁sentence｜>
### Instruction:
FPD_CLIENT-3-INIT_ERROR
### Response:
(Severity: 3), (Category: PLATFORM), (Description: A failure has occured in the FPD Client during process initialization.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco ... |
<｜begin▁of▁sentence｜>
### Instruction:
T1E1_LNM-3-REMWARNNOISE
### Response:
(Severity: 3), (Category: L2), (Description: Noise on the link has either crossed or fallen below the threshold value configured by the user for link removal on the controller identified in the message. Video or voice quality may be affected i... |
<｜begin▁of▁sentence｜>
### Instruction:
SHELFMGRV2-3-SLOT_SPECIFIC_FAILURE
### Response:
(Severity: 3), (Category: PLATFORM), (Description: This message indicates that an operation to get Card Control Block CCB for specific to a slot has failed.), (Recommended Action: Copy the error message exactly as it appears on the ... |
<｜begin▁of▁sentence｜>
### Instruction:
TZ-3-INTERNAL
### Response:
(Severity: 3), (Category: OS), (Description: Serious problem occured.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representativ... |
<｜begin▁of▁sentence｜>
### Instruction:
ISIS-4-EVENT_CONN_ERROR_FAIL
### Response:
(Severity: 4), (Category: ROUTING), (Description: After detecting an error with the connection to the specified service, IS-IS failed to reset that connection. This is an internal error. It requires a restart of the process for recovery.)... |
<｜begin▁of▁sentence｜>
### Instruction:
BFM-4-INIT_ERROR
### Response:
(Severity: 4), (Category: PKT_INFRA), (Description: bfm encountered a error and is not able to recover from the error trying again. A reason text will be supplied call support with this text.), (Recommended Action: Copy the error message exactly as i... |
<｜begin▁of▁sentence｜>
### Instruction:
LOCALD-3-BAG_ENCODE_ERR
### Response:
(Severity: 3), (Category: SECURITY), (Description: Failed to encode a bag.), (Recommended Action: Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide th... |
<｜begin▁of▁sentence｜>
### Instruction:
IKEv2-6-KEYRING_NOT_FOUND
### Response:
(Severity: 6), (Category: SECURITY), (Description: Keyring not found in IKEv2 profile.), (Recommended Action: Configure and attach keyring to IKEv2 profile.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
PHYS_COMMON-6-AINS_STARTED
### Response:
(Severity: 6), (Category: L1), (Description: The notification Indicating Successful (Re)Start of Automatic In-Service Soak Timer), (Recommended Action: None.)
<|EOT|>
|
<｜begin▁of▁sentence｜>
### Instruction:
CANB_SERVER-6-RP_ISOLATION_RESET_REQ
### Response:
(Severity: 6), (Category: PLATFORM), (Description: This is an informational message indicating that RP Isolation is in force, CPU reset request for the target slot is ignored.), (Recommended Action: No action is required.)
<|EOT|>... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.