hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.10.5 Test requirement | After step 1 the UE shall transmit a RADIO BEARER SETUP COMPLETE message on the DCCH using AM RLC.
8.2.1.10a Radio Bearer Establishment for transition from CELL_FACH to CELL_DCH: Success (TDD Only)
8.2.1.10.1a Definition
The features and operation of Multi-frequency and UpPCH shifting have been introduced to core speci... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.11 Radio Bearer Establishment for transition from CELL_FACH to CELL_DCH: Failure (Unsupported configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.11.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.11.2 Conformance requirement | If the UTRAN instructs the UE to use a configuration, which it does not support and/or if the received message causes the variable UNSUPPORTED_CONFIGURATION to be set to TRUE, the UE shall:
1> transmit a failure response as specified in TS 25.331 subclause 8.2.2.9, setting the information elements as specified below:
2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.11.3 Test purpose | To confirm that the UE keeps its configuration and transmits a RADIO BEARER SETUP FAILURE message in case of it receiving a RADIO BEARER SETUP message, which includes parameters of an unsupported configuration. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.11.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH_FACH (state 6-8) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. SS then send a MEASUREMENT CONTROL message to UE. The UE shall perform periodical traffic volume measurement according to this message and then transmit MEASUREM... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.11.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on RACH at every 8s interval.
After step 1 the UE shall transmit a RADIO BEARER SETUP FAILURE message on the DCCH using AM .
After step 2, the UE shall transmit a MEASUREMENT REPORT ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.12 Radio Bearer Establishment for transition from CELL_FACH to CELL_DCH: Failure (Physical channel Failure and successful reversion to old configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.12.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.12.2 Conformance requirement | When a physical dedicated channel establishment is initiated by the UE, the UE shall start a timer T312 and wait for layer 1 to indicate N312 "in sync" indications. On receiving N312 "in sync" indications, the physical channel is considered established and the timer T312 is stopped and reset.
If the timer T312 expires ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.12.3 Test purpose | To confirm that the UE reverts to the old configuration and transmits a RADIO BEARER SETUP FAILURE message when the UE fails to configure the new radio bearer after it detects physical channel failure, followed by the T312 expiry. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.12.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH_FACH (state 6-8) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. SS then send a MEASUREMENT CONTROL message to UE. The UE shall perform periodical traffic volume measurement according to this message and then transmit MEASUREM... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.12.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on RACH at every 8s interval.
After step 1 the UE shall transmit a RADIO BEARER SETUP FAILURE message on the DCCH using AM RLC which is set to "physical channel failure" in IE "failu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.13 Radio Bearer Establishment for transition from CELL_FACH to CELL_DCH: Failure (Physical channel Failure and cell reselection) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.13.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.13.2 Conformance requirement | When a physical dedicated channel establishment is initiated by the UE, the UE shall start a timer T312 and wait for layer 1 to indicate N312 "in sync" indications. On receiving N312 "in sync" indications, the physical channel is considered established and the timer T312 is stopped and reset.
If the timer T312 expires ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.13.3 Test purpose | To confirm that the UE transmit a RADIO BEARER SETUP FAILURE message after it completes a cell update for the physical channel failure in the radio bearer establishment procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.13.4 Method of test | Initial Condition
System Simulator: 2 cells - Cell 1 and 2 are active.
UE: PS-DCCH_FACH (state 6-8) as specified in clause 7.4 of TS 34.108 in cell 1.
Test Procedure
Table 8.2.1.13
Parameter
Unit
Cell 1
Cell 2
T0
T1
T0
T1
UTRA RF Channel Number
Mid Range Test Frequency
Mid Range Test Frequency
CPICH Ec (FDD)
dBm/3.84... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.13.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on RACH at every 8s interval.
After step 4 the UE shall transmit a CELL UPDATE message on the CCCH with IE "Cell update cause" set to "cell reselection".
After step 6 the UE shall tr... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.14 Radio Bearer Establishment for transition from CELL_FACH to CELL_DCH: Failure (Incompatible simultaneous reconfiguration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.14.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.14.2 Conformance requirement | If the received message is any of the messages:
- RADIO BEARER SETUP; or
…
the UE shall:
2> if the variable ORDERED_RECONFIGURATION is set to TRUE; or
…
3> if the IE "RRC transaction identifier" of the received message is identical to the "RRC transaction identifier" stored for the same "Message Type" as the received m... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.14.3 Test purpose | To confirm that if the UE receives a RADIO BEARER SETUP message during a reconfiguring procedure due to a radio bearer message other than RADIO BEARER SETUP, it shall keep its configuration as if the RADIO BEARER SETUP message had not been received and complete the reconfiguration procedure according to the previously ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.14.4 Method of test | Initial Condition
System Simulator: 1 cell
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. The SS transmits a RADIO BEARER RECONFIGURATION message to the UE. The SS transmits a RADIO... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.14.5 Test requirement | After step 2 the UE shall transmit a RADIO BEARER SETUP FAILURE message on the DCCH using AM RLC with IE "failure cause" set to "Incompatible simultaneous reconfiguration".
After step 3 the UE shall configure the new configuration on the activation time and transmit a RADIO BEARER RECONFIGURATION COMPLETE message on th... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.15 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.16 Radio Bearer Establishment for transition from CELL_FACH to CELL_FACH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.16.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.16.2 Conformance requirement | If the UE receives:
- a RADIO BEARER SETUP message; or
it shall:
1> perform the physical layer synchronisation procedure as specified in TS 25.214;
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
The UE shall then:
1... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.16.3 Test purpose | To confirm that the UE establishes a new radio access bearer according to a RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.16.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH_FACH (state 6-8) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state, after the test operator is being prompted to make an outgoing packet-switched call. The SS transmits a RADIO BEARER SETUP message to the UE. After the UE receive... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.16.5 Test requirement | After step 1, the UE shall transmit a RADIO BEARER SETUP COMPLETE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.17 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: success (Subsequently received) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.17.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.17.2 Conformance requirement | If the IE "RRC transaction identifier" is included in a received message, the UE shall perform the actions below. The UE shall:
If the received message is any of the messages:
- RADIO BEARER SETUP; or
…
the UE shall:
2> if the variable ORDERED_RECONFIGURATION is set to TRUE; or
2> if the variable CELL_UPDATE_STARTED is... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.17.3 Test purpose | To confirm that if the UE receives a new RADIO BEARER SETUP message before the UE completes the configuration of the radio bearer according to a previous RADIO BEARER SETUP message, it ignores the new RADIO BEARER SETUP message and configures according to the previous RADIO BEARER SETUP message received. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.17.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH_DCH (state 6-5) or PS-DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. SS transmits a RADIO BEARER SETUP message to the UE before the UE completes the confi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.17.5 Test requirement | After step 2 the UE shall transmit a RADIO BEARER SETUP COMPLETE message on the DCCH using AM RLC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.18 Radio Bearer Establishment for transition from CELL_FACH to CELL_DCH: Success (Subsequently received) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.18.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.18.2 Conformance requirement | If the IE "RRC transaction identifier" is included in a received message, the UE shall perform the actions below. The UE shall:
If the received message is any of the messages:
- RADIO BEARER SETUP; or
…
the UE shall:
2> if the variable ORDERED_RECONFIGURATION is set to TRUE; or
2> if the variable CELL_UPDATE_STARTED is... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.18.3 Test purpose | To confirm that if the UE receives a new RADIO BEARER SETUP message before the UE completes the configuration of the radio bearer according to a previous RADIO BEARER SETUP message, it ignores the new RADIO BEARER SETUP message and configures according to the previous RADIO BEARER SETUP message received. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.18.4 Method of test | Initial Condition
System Simulator: 1 cell.
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS-DCCH_FACH (state 6-8) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. The SS transmits a RADIO BEARER SETUP message, requesting the UE to setup radio bearers using DP... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.18.5 Test requirement | After step 2 the UE shall transmit a RADIO BEARER SETUP COMPLETE message on the DCCH using AM RLC specified in step 1.
After step 3 the UE shall communicate with the SS on the radio bearer specified in the RADIO BEARER SETUP message in step 1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.19 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.20 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.21 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.22 Radio Bearer Establishment for transition from CELL_DCH to CELL_FACH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.22.1 Definition | - |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.22.2 Conformance requirement | If the UE receives:
-a RADIO BEARER SETUP message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
1> enter a state according to TS 25.331 subclause 8.6.3.3.
If after state transition the UE enters CELL_FAC... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.22.3 Test purpose | 1. To confirm that the UE transits from CELL_DCH to CELL_FACH according to the RADIO BEARER SETUP message.
2. To confirm that the UE transmits RADIO BEARER SETUP COMPLETE message on the uplink DCCH using AM RLC on a common physical channel in a different frequency. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.22.4 Method of test | Initial Condition
System Simulator: 2 cells–Cell 1 is active and cell 6 is inactive.
UE: "Registered idle mode on PS" (state 3) in cell 1 as specified in clause 7.4 of TS 34.108. If the UE supports both CS and PS domains, the initial UE state shall be "Registered idle mode on CS/PS" (state 7).
Test Procedure
Table 8.2.... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.22.5 Test requirement | After step 4 the UE shall transmit a CELL UPDATE message on the CCCH in cell 6.
After step 6 the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the DCCH using AM RLC in cell 6.
After step 7 the UE shall transmit a RADIO BEARER SETUP COMPLETE message on the DCCH using AM RLC in cell 6.
After step 8 th... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.23 Radio Bearer Establishment for transition from CELL_FACH to CELL_DCH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.23.1 Definition | - |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.23.2 Conformance requirement | If the UE receives:
-a RADIO BEARER SETUP message;
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (for FDD only);
1> act upon all received information e... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.23.3 Test purpose | 1. To confirm that the UE transits from CELL_FACH to CELL_DCH according to the RADIO BEARER SETUP message.
2. To confirm that the UE transmits RADIO BEARER SETUP COMPLETE message on the uplink DCCH using AM RLC on a dedicated physical channel in a different frequency. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.23.4 Method of test | Initial Condition
System Simulator: 2 cells–Cell 1 is active and cell 6 is inactive.
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: CS-DCCH_FACH (state 6-6) or PS_DCCH_FACH (state 6-8) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
Table ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.23.5 Test requirement | After step 3 the UE shall transmit a RADIO BEARER SETUP COMPLETE message on the DCCH using AM RLC in cell 6.
After step 4 the UE shall be in CELL_DCH state of cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.24 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.24.1 Definition | - |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.24.2 Conformance requirement | If the UE receives:
- a RADIO BEARER SETUP message;
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (for FDD only);
1> act upon all received information ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.24.3 Test purpose | 1. To confirm that the UE transits from CELL_DCH to CELL_DCH according to the RADIO BEARER SETUP message.
2. To confirm that the UE transmits the RADIO BEARER SETUP COMPLETE message on the uplink DCCH using AM RLC on a dedicated physical channel in a different frequency. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.24.4 Method of test | Initial Condition
System Simulator: 2 cells–Cell 1 is active and cell 6 is inactive.
CS-DCCH_DCH (state 6-5) or PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
Table 8.2.1.24
Parameter
Unit
Cell 1
Cell 6
T0
T1
T0
T1
UTRA RF Channel Numbe... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.24.5 Test requirement | After step 4 the UE shall transmit a RADIO BEARER SETUP COMPLETE message on the DCCH using AM RLC in cell 6.
After step 5 the UE shall be in CELL_DCH state of cell 6.
8.2.1.24a Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH (Inter band handover): Success
8.2.1.24a.1 Definition
This test case is ide... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.25 Radio Bearer Establishment for transition from CELL_FACH to CELL_FACH (Frequency modification): Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.25.1 Definition | - |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.25.2 Conformance requirement | If the UE receives:
-a RADIO BEARER SETUP message;
it shall:
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
1> enter a state according to TS 25.331 subclause 8.6.3.3.
If the UE was in CELL_FACH state upon reception ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.25.3 Test purpose | 1. To confirm that the UE transits from CELL_FACH to CELL_FACH according to the RADIO BEARER SETUP message.
2. To confirm that the UE transmits RADIO BEARER SETUP COMPLETE message on the uplink DCCH using AM RLC on a common physical channel in a different frequency. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.25.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 is active and cell 6 is inactive.
UE: "Registered idle mode on PS" (state 3) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain supported by the UE. If the UE supports both CS and PS domains, the initial UE state shall be "Registered idle m... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.25.5 Test requirement | After step 5 the UE shall transmit a CELL UPDATE message on the CCCH in cell 6.
After step 7 the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the DCCH using AM RLC in cell 6.
After step 8 the UE shall transmit a RADIO BEARER SETUP COMPLETE message on the DCCH using AM RLC in cell 6.
After step 9 th... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.26 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.27 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Success (two radio links, start of HS-DSCH reception) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.27.1 Definition and applicability | All UEs which support FDD and HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.27.2 Conformance requirement | In case the procedure was triggered by reception of a RADIO BEARER SETUP message, the UE shall:
1> transmit a RADIO BEARER SETUP COMPLETE as response message on the uplink DCCH using AM RLC.
…
The variable HS_DSCH_RECEPTION shall be set to "TRUE" only when all the following conditions are met:
1> the UE is in CELL_DCH ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.27.3 Test purpose | To confirm that the UE establishes a radio bearer mapped to HS-DSCH according to the received RADIO BEARER SETUP message when having two radio links established. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.27.4 Method of test | Initial Condition
System Simulator: 2 cells - Cell 1 and 2 are active
UE: PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE supports HS-PDSCH
Test Procedure
Table 8.2.1.27
Parameter
Unit
Cell 1
Cell 2
T0
T1
T0
T1
UTRA RF Channel Number
Mid Range Test ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.27.5 Test requirements | After step 3, the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
8.2.1.27a Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Success (start of HS-DSCH reception)
8.2.1.27a.1 Definition and applicability
All UEs which support TDD and HS-PDSCH.
8.2.1.27a.2 Conformance requirement
In case the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.28 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Success (RB mapping for both DL DCH and HS-DSCH in cell without HS-DSCH support) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.28.1 Definition and applicability | All UEs which support FDD or TDD and HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.28.2 Conformance requirement | In case the procedure was triggered by reception of a RADIO BEARER SETUP message, the UE shall:
1> transmit a RADIO BEARER SETUP COMPLETE as response message on the uplink DCCH using AM RLC.
…
The variable HS_DSCH_RECEPTION shall be set to "TRUE" only when all the following conditions are met:
1> the UE is in CELL_DCH ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.28.3 Test purpose | To confirm that the UE establishes a radio bearer mapped to DCH and HS-DSCH according to the received RADIO BEARER SETUP message in a cell without HS-DSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.28.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD or TDD
- UE supports HS-PDSCH
Test Procedure
The UE is in CELL_DCH state. Only signalling radio bearers have been established.
The test operator is prompted to ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.28.5 Test requirements | After step 1, the UE shall transmit a RADIO BEARER SETUP COMPLETE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.29 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Success (Timing re-initialized hard handover to another frequency, uplink TFCS restriction and start of HS-DSCH reception) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.29.1 Definition and applicability | All UEs which support FDD or TDD and HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.29.2 Conformance requirement | In case the procedure was triggered by reception of a RADIO BEARER SETUP message, the UE shall:
1> transmit a RADIO BEARER SETUP COMPLETE as response message on the uplink DCCH using AM RLC.
…
The variable HS_DSCH_RECEPTION shall be set to "TRUE" only when all the following conditions are met:
1> the UE is in CELL_DCH ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.29.3 Test purpose | To confirm that the UE establishes a radio bearer mapped to HS-DSCH using uplink TFCS restriction according to the received RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.29.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 is active and cell 6 is inactive.
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD or TDD
- UE supports HS-PDSCH
Test Procedure
Table ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.29.5 Test requirements | After step 1, the UE shall transmit a RADIO BEARER SETUP COMPLETE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.30 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Success (Timing re-initialised hard handover to another frequency, start of HS-DSCH reception) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.30.1 Definition and applicability | All UEs which support FDD or TDD and HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.30.2 Conformance requirement | In case the procedure was triggered by reception of a RADIO BEARER SETUP message, the UE shall:
1> transmit a RADIO BEARER SETUP COMPLETE as response message on the uplink DCCH using AM RLC.
…
The variable HS_DSCH_RECEPTION shall be set to "TRUE" only when all the following conditions are met:
1> the UE is in CELL_DCH ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.30.3 Test purpose | To confirm that the UE establishes a radio bearer mapped to HS-DSCH and starts HS-DSCH reception in conjunction with a interfrequency hard handover without prior measurement on the target frequency according to the received RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.30.4 Method of test | Initial Condition
System Simulator: 2 cells–Cells 1 and 6 are active.
UE: PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD or TDD
- UE supports HS-PDSCH
Test Procedure
The UE is in CELL_DCH state. Only signalling radio bearers have been established in cell... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.30.5 Test requirements | After step 1, the UE shall transmit a RADIO BEARER SETUP COMPLETE message using AM RLC in cell 6. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.31 Radio Bearer Establishment for transition from CELL_FACH to CELL_DCH: Success (start of HS-DSCH reception) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.31.1 Definition and applicability | All UEs which support FDD or TDD and HS-PDSCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.31.2 Conformance requirement | In case the procedure was triggered by reception of a RADIO BEARER SETUP message, the UE shall:
1> transmit a RADIO BEARER SETUP COMPLETE as response message on the uplink DCCH using AM RLC.
…
If the UE receives a message in which presence is needed for the IE "Activation time", and the value is other than the default ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.31.3 Test purpose | To confirm that the UE establishes a radio bearer mapped to HS-DSCH according to the received RADIO BEARER SETUP message. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.