hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.4 Security mode command in CELL_FACH state (UEA2/UIA2) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.4.1 Definition | Applicable to all Rel-7 UEs which support FDD and PS domain services. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.4.2 Conformance requirement | Same conformance requirement as clause 8.1.7.2.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.4.3 Test purpose | Same test purpose as clause 8.1.7.2.3. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.4.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CELL_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
Same test procedure as clause 8.1.7.2.4 except that ciphering algorithm used is UEA2 and integrity protection algorithm used is UIA2.
Expected sequence
Same expected sequence as clause 8.1.7.2.... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.7.4.5 Test requirement | After step 2 the UE shall transmit a SECURITY MODE FAILURE message to report the protocol error detected in the first SECURITY MODE COMMAND message.
After step 8 the SS checks that the SECURITY MODE COMPLETE message is received ciphered using the old configuration and that the calculated MAC-I values in "integrity chec... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8 Counter check | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.1 Counter check in CELL_DCH state, with symmetric RAB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.1.2 Conformance requirement | When the UE receives a COUNTER CHECK message it shall compare the COUNT-C MSB values received in the IE "RB COUNT-C MSB information" in the COUNTER CHECK message to the COUNT-C MSB values of the corresponding radio bearers.
The UE shall:
1> set the IE "RRC transaction identifier" in the COUNTER CHECK RESPONSE message t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.1.3 Test purpose | To confirm that the UE transmits a COUNTER CHECK RESPONSE message after it receives a COUNTER CHECK message from the SS. To confirm that the UE responds to the reception of an invalid downlink COUNTER CHECK message by transmitting a RRC STATUS message on the uplink DCCH, stating the correct error cause value in message... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.1.5 Test requirement | After step 2, the UE shall transmit a RRC STATUS message on the uplink DCCH. The protocol error cause shall be set to "Message extension not comprehended".
After step 4 the UE shall transmit a COUNTER CHECK RESPONSE message which does not includes the IE "RB COUNT-C information" to indicate that a matched comparison re... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.2 Counter check in CELL_FACH state | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.2.1 Definition | 8.1.8.2.2 Conformance requirement
When the UE receives a COUNTER CHECK message it shall compare the COUNT-C MSB values received in the IE "RB COUNT-C MSB information" in the COUNTER CHECK message to the COUNT-C MSB values of the corresponding radio bearers.
The UE shall:
1> set the IE "RRC transaction identifier" in t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.2.5 Test requirement | After step 2, the UE shall transmit a RRC STATUS message on the uplink DCCH. The protocol error cause shall be set to "Message extension not comprehended".
After step 4 the UE shall transmit a COUNTER CHECK RESPONSE message which does not includes the IE "RB COUNT-C information" to indicate that a matched comparison re... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.3 Counter check in CELL_DCH state, with asymmetric RAB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.3.2 Conformance requirement | When the UE receives a COUNTER CHECK message it shall compare the COUNT-C MSB values received in the IE "RB COUNT-C MSB information" in the COUNTER CHECK message to the COUNT-C MSB values of the corresponding radio bearers.
The UE shall:
1> if no COUNT-C exists for a radio bearer for a given direction (uplink or downli... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.3.3 Test purpose | To confirm that the UE transmits a COUNTER CHECK RESPONSE message even if COUNT-C does not exist for a radio bearer for a given direction for reasons given in the above section.
8.1.8.3.4 Method of test
Initial Condition
System Simulator: 1 cell
UE: CS-DCCH_DCH (state 6-5) or PS-DCCH_DCH (state 6-7) as specified in cl... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.8.3.5 Test requirement | After step 2, the UE shall transmit a RADIO BEARER SETUP COMPLETE message on the uplink DCCH.
After step 4, the UE shall transmit a COUNTER CHECK RESPONSE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.9 Signalling Connection Release Indication | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.9.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.9.2 Conformance requirement | The UE shall, on receiving a request to release (abort) the signalling connection from upper layers for a specific CN domain:
1> if a signalling connection in the variable ESTABLISHED_SIGNALLING_CONNECTIONS for the specific CN domain identified with the IE "CN domain identity" exists:
2> initiate the signalling connect... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.9.3 Test purpose | To confirm that the UE transmits a SIGNALLING CONNECTION RELEASE INDICATION message after upper layer requests to release its signalling connection. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.9.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: Idle state (state 2 or state 3 or state 7) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE transmits an RRC CONNECTION REQUEST message to the SS on the uplink CCCH by attempting to make an outgoing call. Th... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.9.5 Test requirement | After step 7 the UE shall transmit a SIGNALLING CONNECTION RELEASE INDICATION message which includes the same CN domain identity as that found in the INITIAL DIRECT TRANSFER message.
8.1.9a Signalling Connection Release Indication (RLC re-establishment): CS signalling connection release
8.1.9a.1 Definition
8.1.9a.2 Con... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10 Broadcast of system information | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.1 Dynamic change of segmentation, concatenation & scheduling and handling of unsupported information blocks | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.1.2 Conformance requirement | 1. The RRC layer in the UE shall perform re-assembly of segments. All segments belonging to the same master information block, scheduling block or system information block shall be assembled in ascending order with respect to the segment index. When all segments of the master information block, scheduling block or a sy... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.1.3 Test Purpose | 1. To verify that dynamic change of System Information is identified, new information read and used.
2. To verify that the UE can support all segment types and "all" segment combinations.
3. To verify that the UE can dynamically use different configurations
4. To verify that the UE properly uses combinations of Default... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.1.4 Method of test | Alternate two sets of System Information and generate a call after one or the other set has been broadcasted.
These two sets of System Information are based on the System Information specified in 34.108, section 6.
A "Minimum" configuration and a "Maximum" configuration of System Information are defined. The "Minimum" ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.1.5 Test requirement | After step 1 the UE shall have a call/session established in Cell 1.
After step 5 the UE shall have a call/session established in Cell 2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.2 BCCH Mapping on HS-DSCH for Transmitting System Information Change Indication | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.2.1 Definition | All UEs which support FDD and HS-PDSCH in CELL_FACH, except UEs that receive Master information block value tag autonomously before or parallel to receiving SYSTEM INFORMATION CHANGE INDICATION in SYSTEM INFORMATION BLOCK TYPE 5 / SYSTEM INFORMATION BLOCK TYPE 5bis.
8.1.10.2.2 Conformance requirement
Upon modifications... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.2.3 Test Purpose | 1. To verify the correct use of system change indication for BCCH mapped on HS-DSCH
2. To verify operation of BCCH specific H-RNTI
3. To verify that BCCH reception on HS-DSCH uses the first indexed HS-SCCH code listed on the IE HS-SCCH channelization code with BCCH specific H-RNTI |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.2.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: CELL_FACH state with DCCH/DTCH mapped onto HS-DSCH as specified in clause 7.4 of TS 34.108 with dedicated H-RNTI and C-RNTI assigned.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE supports HS-PDSCH in CELL_FACH
Test Procedure
The SS transmits the new SYSTEM INFORMAT... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.2.5 Test requirement | At step 7 the UE shall not respond to the UE CAPABILITY ENQUIRY message sent in step 6.
At step 9 the UE shall transmit a UE CAPABILITY INFORMATION message on the uplink DCCH to respond to the downlink UE CAPABILITY ENQUIRY message with correct contents.
At step 16 the UE shall not respond to the UE CAPABILITY ENQUIRY ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.3 BCCH Mapping on HS-DSCH for Transmitting System Information Change Indication (1.28Mcps TDD) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.3.1 Definition | All UEs which support 1.28Mcps TDD and HS-PDSCH in CELL_FACH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.3.2 Conformance requirement | Upon modifications of system information blocks using value tags, UTRAN should notify the new value tag for the master information block in the IE "BCCH modification info", transmitted in the following way:
…
1> for FDD and 1.28 Mcps TDD, to reach UEs in CELL_FACH state with HS-DSCH assigned and in CELL_PCH with HS-DSC... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.3.3 Test Purpose | 4. To verify the correct use of system change indication for BCCH mapped on HS-DSCH
5. To verify operation of BCCH specific H-RNTI
6. To verify that BCCH reception on HS-DSCH uses the first indexed HS-SCCH code listed on the IE HS-SCCH channelization code with BCCH specific H-RNTI |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.3.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: CELL_FACH state with DCCH/DTCH mapped onto HS-DSCH as specified in clause 7.4 of TS 34.108 with dedicated H-RNTI and C-RNTI assigned.
Related ICS/IXIT statement(s)
- UE supports 1.28Mcps TDD
- UE supports HS-PDSCH in CELL_FACH
Test Procedure
The SS transmits the new SYSTEM... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.10.3.5 Test requirement | At step 7 the UE shall not respond to the UE CAPABILITY ENQUIRY message sent in step 6.
At step 9 the UE shall transmit a UE CAPABILITY INFORMATION message on the uplink DCCH to respond to the downlink UE CAPABILITY ENQUIRY message with correct contents.
At step 16 the UE shall not respond to the UE CAPABILITY ENQUIRY ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.11 Signalling Connection Release (Invalid configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.11.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.11.2 Conformance requirement | Upon reception of a SIGNALLING CONNECTION RELEASE message, the UE shall:
1> indicate the release of the signalling connection and pass the value of the IE "CN domain identity" to upper layers;
1> remove the signalling connection with the identity indicated by the IE "CN domain identity" from the variable ESTABLISHED_SI... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.11.3 Test purpose | To confirm that the UE ignores the SIGNALLING CONNECTION RELEASE REQUEST message which request the UE to release signalling connection of domain that contains established radio access bearers.
To confirm that the UE transmit a RRC STATUS message to SS after detecting an invalid configuration in the received message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.11.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS_DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
SS transmit MEASUREMENT CONTROL message to UE. In this message, SS requests UE to perform traffic volum... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.11.5 Test requirement | After step 1 the UE shall transmit MEASUREMENT REPORT message twice at an interval of 6 seconds.
After step 4 the UE shall transmit a RRC STATUS message with protocol error cause set to "Message not compatible with receiver state".
After step 5 the UE shall transmit a MEASUREMENT REPORT within 6 seconds. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.12 Integrity Protection | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.12.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.12.2 Conformance requirement | If the UE receives an RRC message on signalling radio bearer with RB identity n, the "Status" in the variable INTEGRITY_PROTECTION_INFO has the value "Started" and the IE 'Integrity check info' is present the UE shall:
1> check the value of the IE "RRC message sequence number" included in the IE "Integrity check info";... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.12.3 Test purpose | To confirm that the UE discards any RRC messages that include wrong message authentication code, or RRC message sequence number, or do not include the IE "Integrity Check Info" after integrity protection is activated. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.12.4 Method of test | Initial Condition
System Simulator: 1cell.
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS_DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE after integrity protection is activated on all SRBs.
Test Procedure
The UE is in CELL_DCH state, radio access bearer and... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.1.12.5 Test requirement | After step 1 the UE shall not transmit RRC CONNECTION RELEASE COMPLETE message on the uplink DCCH.
After step 3 the UE shall not transmit RRC CONNECTION RELEASE COMPLETE message on the uplink DCCH.
After step 8 the UE shall not transmit RRC CONNECTION RELEASE COMPLETE message on the uplink DCCH.
After step 10 the UE sh... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1 Radio Bearer Establishment | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.1 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.1.2 Conformance requirement | If the UE receives:
- a RADIO BEARER SETUP message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (FDD only);
1> act upon all received information e... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.1.3 Test purpose | To confirm that the UE establishes a new radio bearer according to a RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.1.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: CS-DCCH_DCH (state 6-5) or PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state, after the test operator is prompted to make an out-going call. Before step 1, only sig... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.1.5 Test requirement | After step 1 the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
8.2.1.1a Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Success (TDD Only)
8.2.1.1a.1 Definition
The features and operation of Multi-frequency and UpPCH shifting have been introduced to core specification (TS 25.331 clause 8... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.2 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.3 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Failure (Unsupported configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.3.2 Conformance requirement | If the UTRAN instructs the UE to use a configuration, which it does not support and/or if the received message causes the variable UNSUPPORTED_CONFIGURATION to be set to TRUE, the UE shall:
1> transmit a failure response as specified in TS 25.331 subclause 8.2.2.9, setting the information elements as specified below:
2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.3.3 Test purpose | To confirm that the UE keeps its configuration and transmits a RADIO BEARER SETUP FAILURE message in case of receiving a RADIO BEARER SETUP message which includes parameters of its unsupported configuration. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.3.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH_DCH (state 6-5) or PS_DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108, depending on the domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. SS then send a MEASUREMENT CONTROL message to UE. The UE shall perform periodical traffi... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.3.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on DCH at every 8s interval.
After step 1 the UE transmit a RADIO BEARER SETUP FAILURE message on the DCCH using AM RLC .
After step 2, the UE shall transmit a MEASUREMENT REPORT mes... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.4 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Failure (Physical channel Failure and successful reversion to old configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.4.2 Conformance requirement | When a physical dedicated channel establishment is initiated by the UE, the UE shall start a timer T312 and wait for layer 1 to indicate N312 "in sync" indications. On receiving N312 "in sync" indications, the physical channel is considered established and the timer T312 is stopped and reset.
If the timer T312 expires ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.4.3 Test purpose | To confirm that the UE reverts to the old configuration and transmits a RADIO BEARER SETUP FAILURE message on the DCCH using AM RLC, if the UE fails to reconfigure the radio bearer according to the RADIO BEARER SETUP message before timer T312 expires. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.4.4 Method of test | Initial Condition
System Simulator: 2 cells. – Cell 1 is active and cell 2 is inactive.
UE: CS-DCCH_DCH (state 6-5) or PS-DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108, depending on the domain(s) supported by the UE.
Test Procedure
Table 8.2.1.4
Parameter
Unit
Cell 1
Cell 2
T0
T1
T0
T1
UTRA RF Channel Nu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.4.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on DCH at every 8s interval.
After step 2 the UE shall transmit a RADIO BEARER SETUP FAILURE message on the DCCH using AM RLC which is set to "physical channel failure" in IE "failur... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.5 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.6 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.7 Radio Bearer Establishment for transition from CELL_DCH to CELL_DCH: Failure (Invalid message reception and Invalid configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.7.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.7.2 Conformance requirement | If the received reconfiguration message contains a protocol error causing the variable PROTOCOL_ERROR_REJECT to be set to TRUE according to TS 25.331 clause 9, the UE shall perform procedure specific error handling as follows. The UE shall:
1> transmit a failure response message as specified in TS 25.331 subclause 8.2.... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.7.3 Test purpose | To confirm that the UE transmits a RADIO BEARER SETUP FAILURE message on the DCCH using AM RLC if it receives an invalid RADIO BEARER SETUP message which contains an unexpected critical message extension.
To confirm that the UE transmits a RADIO BEARER SETUP FAILURE message on the DCCH using AM RLC if it receives a RAD... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.7.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: CS-DCCH_DCH (state 6-5) or PS-DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. SS then send a MEASUREMENT CONTROL message to UE. The UE shall perform periodical traf... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.7.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on DCH at every 8s interval.
After step 1 the UE shall keep its old configuration and transmit a RADIO BEARER SETUP FAILURE message on the DCCH using AM RLC which is set to "protocol... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.8 Radio Bearer Establishment for transition from CELL_DCH to CELL_FACH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.8.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.8.2 Conformance requirement | If the UE receives:
- a RADIO BEARER SETUP message; or
it shall:
1> perform the physical layer synchronisation procedure as specified in TS 25.214 (FDD only);
1> act upon all received information elements as specified in TS 25.331 subclause 8.6, unless specified in the following and perform the actions below.
The UE sh... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.8.3 Test purpose | To confirm that the UE establishes a new radio bearer according to a RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.8.4 Method of test | Initial Condition
System Simulator: 1 cell.
NOTE: The ‘timer poll’ value in the SS RLC transmit entity should be set to 800 ms.
UE: PS-DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_DCH state, after the test operator is asked to initiate a packet-switched data call. The S... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.8.5 Test requirement | After step 1 the UE shall transmit a RADIO BEARER SETUP COMPLETE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.9 Radio Bearer Establishment for transition from CELL_DCH to CELL_FACH: Success (Cell re-selection) | 8.2.1.9.1 Definition |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.9.2 Conformance requirement | 1. If after state transition the UE enters CELL_FACH state, the UE shall, after the state transition:
……
- if the contents of the variable C_RNTI is empty:
- perform a cell update procedure according to clause 8.3.1 using the cause "Cell reselection";
2. If the CELL UPDATE CONFIRM message
- does not include "RB informa... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.9.3 Test purpose | 1. To verify that the UE when receiving a RADIO BEARER SETUP message not including a value for C-RNTI initiate a cell update procedure and indicating the cause "Cell reselection".
2. To verify that the UE when the CELL UPDATE CONFIRM message does not include "RB information elements", "Transport channel information ele... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.9.4 Method of test | Initial Condition
System Simulator: 1 cell- Cell 1 is active.
NOTE: The 'timer poll' value in the SS RLC transmit entity should be set to 800 ms.
UE: PS-DCCH_DCH (state 6-7) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_DCH state. The SS transmits a RADIO BEARER SETUP message which includes ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.9.5 Test requirement | 1. After step 3 the UE shall transmit a CELL UPDATE message on the CCCH with IE "Cell update cause" set to "cell reselection".
2. After step 5 the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the DCCH using AM RLC.
3. After step 6 the UE shall transmit a RADIO BEARER SETUP COMPLETE message on the D... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.10 Radio Bearer Establishment for transition from CELL_FACH to CELL_DCH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.10.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.10.2 Conformance requirement | If the UE receives:
- a RADIO BEARER SETUP message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (FDD only);
1> act upon all received information e... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.10.3 Test purpose | To confirm that the UE establishes a new radio bearer according to a RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.10.4 Method of test | Initial Condition
System Simulator: 1 cell.
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS-DCCH_FACH (state 6-8) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state, after SS prompts the test operator to initiate a packet-switched data call. The SS transmits a R... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.