hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.1 Radio Bearer Establishment for transition between CELL_DCH and CELL_DCH with SRBs mapped on DCH: Successful Activation of 2cell/single frequency Multiflow HSDPA , Intra-NodeB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.1.1 Definition and applicability | UE categories (Cat 21, Cat 22, Cat 23, Cat 24, Cat 25, Cat 26, Cat 27 or Cat 28) which support combination of Multiflow HSDPA on Single Frequency/Dual Cell (SF-DC)..
UE supports FDD. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.1.2 Conformance requirement | If the UE receives:
- a RADIO BEARER SETUP message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (FDD only);
1> act upon all received information e... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.1.3 Test purpose | To confirm that the UE establishes radio bearer mapped to HS-DSCH, transits from CELL_DCH to CELL_DCH state, and starts simultaneous 16QAM reception over multiflow HSDPA operation (Single Frequency/Dual Cell Multiflow HSDPA for Single band) according to the received RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.1.4 Method of test | Initial Condition
System Simulator:
2 cells –Cell 1/2 with Cell 1 (f1) (Serving HS-DSCH cell), and Cell 2 (f1) (Assisting Serving HS-DSCH cell) – One Carrier on DL Band A (Single Band SF-DC). Tcell of Cell 2 is set to 3840 chips (1.5 slots).
UE: CELL_DCH (state 6-7) as specified in clause 7.4 of TS 34.108[9]. The proce... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.1.5 Test requirements | At step 2 the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
At step 4 the UE shall transmit UE CAPABILITY INFORMATION on SRB2.
At step 6 the UE shall transmit CQI reports for the 2 cells. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.2 Radio Bearer Establishment for transition between CELL_DCH and CELL_DCH with SRBs mapped on DCH: Successful Activation of 3 cell/two frequencies Multiflow HSDPA for Single band, Intra-NodeB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.2.1 Definition and applicability | UE categories (Cat 29 or Cat 30) which support combination of Multiflow HSDPA on Dual Frequency/3 Cell on Single Band (SB-DF-3C)..
UE supports FDD. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.2.2 Conformance requirement | Same as Subclause 8.2.1.45.1.2 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.2.3 Test purpose | To confirm that the UE establishes radio bearer mapped to HS-DSCH, transits from CELL_DCH to CELL_DCH state, and starts simultaneous 16QAM reception over multiflow HSDPA operation (Dual Frequency/3 Cell Multiflow HSDPA for Single band) according to the received RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.2.4 Method of test | Initial Condition
System Simulator:
SS configures Cells 2 and 3 as per Table 5. 0aB of TS 25.101 [21] and TS 34.108 [9], clause 5.1.1.
3 cells –Cell 1/2/3 with Cell 1 (f1) (Serving HS-DSCH cell), and Cell 2 (f1) (Assisting Serving HS-DSCH cell) and Cell 3(f2) (Assisting Secondary serving HS-DSCH Cell) – Two Carriers on... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.2.5 Test requirements | At step 2 the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
At step 4 the UE shall transmit UE CAPABILITY INFORMATION on SRB2.
At step 6 the UE shall transmit CQI reports for the 3 cells. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.3 Radio Bearer Establishment for transition between CELL_DCH and CELL_DCH with SRBs mapped on DCH: Successful Activation of 3 cells/two frequencies Multiflow HSDPA for Dual Bands, intra-NodeB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.3.1 Definition and applicability | UE categories (Cat 29 or Cat 30) which support combination of Multiflow HSDPA on Dual Frequency/3 Cell on Dual Band..
UE supports FDD. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.3.2 Conformance requirement | Same as Subclause 8.2.1.45.1.2 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.3.3 Test purpose | To confirm that the UE establishes radio bearer mapped to HS-DSCH, transits from CELL_DCH to CELL_DCH state, and starts simultaneous 16QAM reception over multiflow HSDPA operation (Dual Frequency/3 Cell Multiflow HSDPA for Dual band) according to the received RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.3.4 Method of test | Initial Condition
System Simulator:
SS configures Cells 2 and 3 as per Table 5.0aC of TS 25.101 [21] and TS 34.108 [9]], clause 5.1.1.
3 cells –Cell 1/2/3 with Cell 1 (f1) (Serving HS-DSCH cell), and Cell 2 (f1) (Assisting Serving HS-DSCH cell) and Cell 3(f2) (Assisting Secondary HS-DSCH cell) – One Carrier on Band A, ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.45.3.5 Test requirements | Same as Subclause 8.2.1.45.2.5 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46 Radio Bearer Establishment for transition between CELL_DCH and CELL_DCH with SRBs mapped on DCH: Successful Activation of Multiflow HSDPA for different bands/Inter Node B, 16QAM/64QAM, 16QAM, assisting serving cell as time reference cell | NOTE: The Radio Bearer Reconfiguration for transition between CELL_DCH & CELL_DCH for Multiflow HSDPA have been split into single band (with two cells on one frequency and with three cells on two frequencies), and dual band (with three cells on two frequencies). |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.1 Radio Bearer Establishment for transition between CELL_DCH and CELL_DCH with SRBs mapped on DCH: Successful Activation of 2cell/single frequency Multiflow HSDPA for single band, inter-NodeB, 16QAM/64QAM, 16QAM, assisting serving cell as time reference cell | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.1.1 Definition and applicability | UE categories that support Multiflow HSDPA operation on two cells on one frequency in single band. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.1.2 Conformance requirement | …
If the UE receives:
...
- a RADIO BEARER RECONFIGURATION message; or
it shall:
…
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> if COMMON_E_DCH_TRANSMISSION is set to FALSE before entering CELL_DCH state or IE "E-DCH info" is not included in... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.1.3 Test purpose | To confirm that the UE establishes radio bearer mapped to HS-DSCH, transits from CELL_DCH to CELL_DCH state, and starts simultaneous 16QAM/64QAM reception over multiflow HSDPA operation (Single Frequency/Dual Cell Multiflow HSDPA for Single band) with the assisting cell as a time reference one according to the receiv... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.1.4 Method of test | Initial Condition
System Simulator: 2 cells –Cell 1/2 with Cell 1 (f1) (Serving cell), and Cell 2 (f1) (Assisting serving cell) –One Carrier on Band A. Tcell of Cell 1 is set to 3840 chips (1.5 slots).
UE: CELL_DCH (state 6-7) as specified in clause 7.4 of TS 34.108 [9]. The procedure P9b in TS 34.108 [9], clause 7.4.2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.1.5 Test requirements | At step 2 the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
At step 4 the UE shall transmit UE CAPABILITY INFORMATION on SRB2.
At step 6 the UE shall transmit CQI reports. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.2 Radio Bearer Establishment for transition between CELL_DCH and CELL_DCH with SRBs mapped on DCH: Successful Activation of 3 cell/two frequencies Multiflow HSDPA for single band, inter-NodeB, 16QAM/64QAM, 16QAM, assisting serving cell as time reference cell | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.2.1 Definition and applicability | UE categories that support Multiflow HSDPA operation on three cells on two frequencies in single band. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.2.2 Conformance requirement | Same as in sub-clause 8.2.1.46.1.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.2.3 Test purpose | To confirm that the UE establishes radio bearer mapped to HS-DSCH, transits from CELL_DCH to CELL_DCH state, and starts simultaneous 16QAM/64QAM reception over multiflow HSDPA operation (Dual Frequency/3 Cell Multiflow HSDPA for Single band) with the assisting cell as a time reference one according to the received RA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.2.4 Method of test | Initial Condition
System Simulator: 3 cells –Cell 1/2/3 with Cell 1 (f1) (Serving cell), and Cell 2 (f1) (Assisting serving cell) and Cell 3(f2) (Secondary serving cell) – Two carriers on Band A. Tcell of Cell 1 and Cell 3 is set to 3840 chips (1.5 slots).
(Ref. to Table 5.0aB of TS 25.101 [21])
UE: CELL_DCH (state 6-7... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.2.5 Test requirements | Same as sub-clause 8.2.1.46.1.5. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.3 Radio Bearer Establishment for transition between CELL_DCH and CELL_DCH with SRBs mapped on DCH: Successful Activation of 3 cells/two frequencies Multiflow HSDPA for dual bands, inter-NodeB, 16QAM/64QAM, 16QAM, assisting serving cell as time reference cell | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.3.1 Definition and applicability | UE categories that support Multiflow HSDPA operation on three cells on two frequencies in two bands. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.3.2 Conformance requirement | Same as in sub-clause 8.2.1.46.1.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.3.3 Test purpose | To confirm that the UE establishes radio bearer mapped to HS-DSCH, transits from CELL_DCH to CELL_DCH state, and starts simultaneous 16QAM/64QAM reception over multiflow HSDPA operation (Dual Frequency/3 Cell Multiflow HSDPA for Dual band) with the assisting cell as a time reference one according to the received RADI... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.3.4 Method of test | Initial Condition
System Simulator: 3 cells –Cell 1/2/3 with Cell 1 (f1) (Serving cell), and Cell 2 (f1) (Assisting serving cell) and Cell 3(f2) (Secondary serving cell) – One Carrier on Band A, and One Carrier on Band B. Tcell of Cell 1 and Cell 3 is set to 3840 chips (1.5 slots).
(Ref. to Table 5.0aC of TS 25.101 [2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.46.3.5 Test requirements | Same as sub-clause 8.2.1.46.1.5. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.47 Radio Bearer Establishment for transition between CELL_DCH and CELL_DCH with SRBs mapped on DCH: Successful Activation of DCH Enhancements in Basic Mode | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.47.1 Definition and applicability | All UEs which supports DCH Enhancements in Basic Mode.
UE supports FDD. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.47.2 Conformance requirement | The UE shall:
1> be able to receive any of the following messages:
2> RADIO BEARER SETUP message; or
…
…
If the UE receives:
- a RADIO BEARER SETUP message; or
…
it shall:
1> stop and reset timer T324 if running;
1> stop monitoring target cell HS-SCCH;
1> set the variable ORDERED_RECONFIGURATION to TRUE;
…
In case the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.47.3 Test purpose | To confirm that the UE establishes radio bearer, mapped to DCH, transits from CELL_DCH to CELL_DCH state, and starts DCH Enhancements in Basic Mode according to the received RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.47.4 Method of test | Initial Condition
System Simulator: 1 cell –Cell 1
UE: Idle state (state 7) as specified in clause 7.4 of TS 34.108, on the CS/PS domain supported by the UE.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE category supports DCH Enhancements
Test Procedure
The UE is in idle state. Before step 1, only signalling rad... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.47.5 Test requirements | 1. At step 3 the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
2. At step 8 the UE shall return an RLC SDU on each of RB5, RB6 and RB7 with transmitted transport format by the SS, having the same content as sent by SS. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.48 Radio Bearer Establishment for transition between CELL_DCH and CELL_DCH with SRBs mapped on DCH: Successful Activation of DCH Enhancements in Full Mode | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.48.1 Definition and applicability | All UEs which supports DCH Enhancements in Full Mode.
UE supports FDD. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.48.2 Conformance requirement | The UE shall:
1> be able to receive any of the following messages:
2> RADIO BEARER SETUP message; or
…
…
If the UE receives:
- a RADIO BEARER SETUP message; or
…
it shall:
1> stop and reset timer T324 if running;
1> stop monitoring target cell HS-SCCH;
1> set the variable ORDERED_RECONFIGURATION to TRUE;
…
In case the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.48.3 Test purpose | To confirm that the UE establishes radio bearer, mapped to DCH, transits from CELL_DCH to CELL_DCH state, and starts DCH Enhancements in Full Mode according to the received RADIO BEARER SETUP message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.48.4 Method of test | Initial Condition
System Simulator: 1 cell –Cell 1
UE: Idle state (state 7) as specified in clause 7.4 of TS 34.108, on the CS/PS domain supported by the UE.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE category supports DCH Enhancements in Full Mode
Test Procedure
The UE is in idle state. Before step 1, only s... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.1.48.5 Test requirements | 1. At step 3 the UE shall transmit a RADIO BEARER SETUP COMPLETE message.
2. At step 8 the UE shall return an RLC SDU on each of RB5, RB6 and RB7 with transmitted transport format by the SS, having the same content as sent by SS. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2 Radio Bearer Reconfiguration | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.1 Radio Bearer Reconfiguration from CELL_DCH to CELL_DCH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.1.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RECONFIGURATION message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (FDD only);
1> act upon all received inf... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.1.3 Test purpose | To confirm that the UE reconfigures the radio bearers according to a RADIO BEARER RECONFIGURATION message, which indicates a change of UL scrambling code and change of RLC parameters. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.1.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. The SS transmits a RADIO BEARER RECONFIGURATION message to the UE, which c... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.1.5 Test requirement | After step 3 the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message on the new DPCH after the specified activation time has expired.
After step 6, the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message.
8.2.2.1a Radio Bearer Reconfiguration from CELL_DCH to CELL_DCH: Success (TDD Only)
8.2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.2 Radio Bearer Reconfiguration from CELL_DCH to CELL_DCH: Failure (Unsupported configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.2.2 Conformance requirement | If the UTRAN instructs the UE to use a configuration, which it does not support and/or if the received message causes the variable UNSUPPORTED_CONFIGURATION to be set to TRUE, the UE shall:
1> transmit a failure response as specified in TS 25.331 subclause 8.2.2.9, setting the information elements as specified below:
2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.2.3 Test purpose | To confirm that the UE transmits a RADIO BEARER RECONFIGURATION FAILURE message on the DCCH using AM RLC if the received RADIO BEARER RECONFIGURATION message includes unsupported configuration parameters. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.2.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. SS then send a MEASUREMENT CONTROL message to UE. The UE shall perform per... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.2.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on DCH at every 8s interval.
After step 1 the UE shall transmit a RADIO BEARER RECONFIGURATION FAILURE message on the DCCH using AM RLC .
After step 2, the UE shall transmit a MEASUR... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.3 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.4 Radio Bearer Reconfiguration from CELL_DCH to CELL_DCH: Failure (Physical channel failure and cell reselection) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.4.2 Conformance requirement | If the received message caused the UE to be in CELL_DCH state and the UE failed to establish the dedicated physical channel(s) indicated in the received message the UE shall:
1> revert to the configuration prior to the reception of the message (old configuration);
1> if the old configuration includes dedicated physical... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.4.3 Test purpose | To confirm that the UE transmits a RADIO BEARER RECONFIGURATION FAILURE message after it completes a cell update procedure when the UE cannot reconfigure the new radio bearer and a subsequent failure to revert to the old configuration. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.4.4 Method of test | Initial Condition
System Simulator: 1 cell.
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. SS then s... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.4.5 Test requirement | After step 0a, the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH, reporting the RLC buffer payload of each RBs mapped on DCH at every 8s interval.
After step 2 the UE shall transmit a CELL UPDATE message on the CCCH with IE "Cell update cause" set to "radio link failure".
After step 5 the UE shall t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.5 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.6 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.7 Radio Bearer Reconfiguration from CELL_DCH to CELL_DCH: Success (Continue and stop) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.7.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.7.2 Conformance requirement | If the IE "RB information to reconfigure" is included, the UE shall apply the following actions on the radio bearer identified with the value of the IE "RB identity". The UE shall:
…
- if the IE "RB stop/continue" is included; and
- if the "RB identity" has a value greater than 2; and
- if the value of the IE "RB stop/... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.7.3 Test purpose | To confirm that the UE reconfigures new radio bearer and stop the transmission and reception of the RLC entity belonging to the RB identity specified in the RADIO BEARER RECONFIGURATION message.
To confirm that the UE reconfigures new radio bearer and restart the transmission and reception of the RLC entity belonging t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.7.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: CS-DCCH+DTCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in CELL_DCH state. The SS transmits a RADIO BEARER RECONFIGURATION message including IE "RB stop/... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.7.5 Test requirement | After step 3 the UE shall respond with a IDENTITY RESPONSE message.
After step 6 the UE shall not respond with a IDENTITY RESPONSE message on the stopped RB. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.8 Radio Bearer Reconfiguration from CELL_DCH to CELL_FACH: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.8.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.8.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RECONFIGURATION message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (for FDD only);
1> act upon all received... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.8.3 Test purpose | To confirm that the UE establishes the reconfigured radio bearer(s) using common physical channel, after UE receives a RADIO BEARER RECONFIGURATION message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.8.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_DCH state. The SS transmits a RADIO BEARER RECONFIGURATION message, which invoke a transition from CELL_DCH to CELL_FACH. The UE reconfigures the radio bearers and tran... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.8.5 Test requirement | After step 1 the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.9 Radio Bearer Reconfiguration from CELL_DCH to CELL_FACH: Success (Cell re-selection) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.9.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.9.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RECONFIGURATION message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (for FDD only);
1> act upon all received... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.9.3 Test purpose | To confirm that the UE transmits RADIO BEARER RECONFIGURATION COMPLETE message after it completes a cell update procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.9.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108.
NOTE: The 'timer poll' value in the SS RLC transmit entity should be set to 800 ms.
Test Procedure
The UE is in CELL_DCH state. The SS transmits a RADIO BEARER RECONFIGURATION message, which includes I... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.9.5 Test requirement | After step 3, the UE shall transmit CELL UPDATE message on the CCCH with IE "Cell update cause" set to "cell reselection".
After step 5, the UE shall transmit UTRAN MOBILITY INFORMATION CONFIRM message and then followed by RADIO BEARER RECONFIGURATION COMPLETE message on the DCCH using AM RLC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.10 Radio Bearer Reconfiguration: from CELL_FACH to CELL_DCH including modification of previously signalled CELL_DCH configuration: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.10.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.10.2 Conformance requirement | If the UE receives:
- a RADIO BEARER RECONFIGURATION message; or
it shall:
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> perform the physical layer synchronisation procedure A as specified in TS 25.214 (for FDD only);
1> act upon all received... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.10.3 Test purpose | To confirm that the UE applies a previously signalled configuration for CELL_DCH and in addition modifies the parameters for which reconfiguration is requested in the RADIO BEARER RECONFIGURATION message that is used to initiate transition from CELL_FACH to CELL_DCH.8.2.2.10.4 Method of test
Initial Condition
System Si... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.10.5 Test requirement | After step 2 the UE shall transmit a RADIO BEARER RECONFIGURATION COMPLETE message on the DCCH using AM RLC. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.11 Radio Bearer Reconfiguration from CELL_FACH to CELL_DCH: Failure (Unsupported configuration) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.11.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.11.2 Conformance requirement | If the UTRAN instructs the UE to use a configuration, which it does not support and/or if the received message causes the variable UNSUPPORTED_CONFIGURATION to be set to TRUE, the UE shall:
1> transmit a failure response as specified in subclause 8.2.2.9, setting the information elements as specified below:
2> include ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.11.3 Test purpose | To confirm that the UE transmits a RADIO BEARER RECONFIGURATION FAILURE message on the DCCH using AM RLC if the received RADIO BEARER RECONFIGURATION message includes unsupported configuration parameters. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.11.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in CELL_FACH state. The SS transmits a RADIO BEARER RECONFIGURATION message, which includes unsupported configuration parameters, to the UE. The UE shall transmit a RADIO BEAR... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.2.11.5 Test requirement | After step 1 the UE shall transmit a RADIO BEARER RECONFIGURATION FAILURE message on the DCCH using AM RLC.
8.2.2.11a Radio Bearer Reconfiguration from CELL_FACH to CELL_DCH: Failure (Unsupported configuration) (1.28 Mcps TDD Only)
8.2.2.11a.1 Definition
8.2.2.11a.2 Conformance requirement
If the UTRAN instructs the UE... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.