hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.68 Physical channel reconfiguration for transition from CELL_DCH to CELL_DCH: Success (Start of SPS operation with initial SPS resource) (1.28 Mcps TDD) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.68.1 Definition and applicability | All UEs which support TDD and SPS operation. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.68.2 Conformance requirement | If the UE receives RRC CONNECTION SETUP, CELL UPDATE CONFIRM, or any reconfiguration message:
1> the UE shall determine the value for the HS_DSCH_SPS_STATUS variable.
The variable HS_DSCH_SPS_STATUS shall be set to TRUE only when all the following conditions are met:
1> the UE is in CELL_DCH state;
1> the variable HS_D... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.68.3 Test purpose | To confirm that the UE reconfigures the physical layer to perform SPS operation according to the IE E-DCH SPS Information and HS-DSCH SPS Information received in PHYSICAL CHANNEL RECONFIGURATION message from the SS. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.68.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH +DTCH_HS-DSCH +DTCH_E-DCH (state 6-18) under condition A13 in cell 1 as specified in clause 7.4 of TS 34.108
Related ICS/IXIT statement(s)
- UE supports TDD
- UE supports SPS operation
Test Procedure
The UE is in state 6-18 under condition A13 as specified in TS 34... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.68.5 Test requirements | After step 1, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC.
After step 2, the UE shall be in Cell_DCH state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.69 Physical channel reconfiguration for transition from CELL_DCH to CELL_DCH: Success (Start of Control Channel DRX operation) (1.28 Mcps TDD) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.69.1 Definition and applicability | All UEs which support TDD and Control Channel DRX. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.69.2 Conformance requirement | If the UE receives:
- a RADIO BEARER SETUP message; or
…
it shall:
…
1> for 1.28 Mcps TDD, if the IEs "Control Channel DRX Information" is stored in the UE:
2> determine the value for the CONTROL_CHANNEL_DRX_STATUS variable and take the corresponding actions as described in subclause 8.5.53.
…
If the UE receives RRC CO... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.69.3 Test purpose | To confirm that the UE reconfigures the physical layer to perform Control Channel DRX according to the IE Control Channel DRX information received in PHYSICAL CHANNEL RECONFIGURATION message from the SS. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.69.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH +DTCH_HS-DSCH +DTCH_E-DCH (state 6-18) under condition A13 in cell 1 as specified in clause 7.4 of TS 34.108
Related ICS/IXIT statement(s)
- UE supports TDD
- UE supports Control Channel DRX
Test Procedure
The UE is in state 6-18 under condition A13 as specified in... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.6.69.5 Test requirements | After step 1, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC.
At step 3, the control channel DRX operation has been activated successfully.
After step 3, the UE shall be in Cell_DCH state |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.7 Physical Shared Channel Allocation [TDD only] | [Editor's note: This message is not included in Release99 so this is FFS.] |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.8 PUSCH capacity request [TDD only] | [Editor's note: This message is not included in Release99 so this is FFS.] |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.9 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10 WLAN Interworking in RRC Connected state | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.1 WLAN Offload / Offload Success / UTRA RRC_Connected to/from WLAN (RSRPmeas, BackhaulRateUlWLAN) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.1.1 Definition | FFS |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.1.2 Conformance requirement | The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.1.3 Test purpose | 1. To verify that a UE offloads from UTRA RRC_Connected to WLAN when RSRPmeas < ThreshServingOffloadWLAN, Low and BackhaulRateUlWLAN > ThreshBackhRateULWLAN, High.
2. To verify that a UE offloads from WLAN to UTRA RRC_Connected when RSRPmeas > ThreshServingOffloadWLAN, High and BackhaulRateUlWLAN > ThreshBackhRateULWL... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.1.4 Method of test | Initial Condition
- Cell 1 and Cell 39 are configured. Cell 39 is switched off.
- System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.
- UE is in State 6-16 on Cell 1 as specified in clause 7.4 of TS 34.108.
The reference system configuration from TS 34.108 clause 6.1 is u... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.1.5 Test requirement | 1) In Step 6, UE shall offload to Cell 39.
2) In Step 10, UE shall offload to Cell 1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.2 WLAN Offload / Offload Success / UTRA RRC_Connected to/from WLAN (RSRPmeas, ChannelUtilizationWLAN) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.2.2 Conformance requirement | The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.2.3 Test purpose | 1. To verify that a UE offloads from UTRA RRC_Connected to WLAN when RSRPmeas < ThreshServingOffloadWLAN, Low and ChannelUtilizationWLAN < ThreshChUtiWLAN, Low
2. To verify that a UE offloads from WLAN to UTRA RRC_Connected when RSRPmeas > ThreshServingOffloadWLAN, High and ChannelUtilizationWLAN < ThreshChUtilWLAN, H... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.2.4 Method of test | Initial Condition
- Cell 1 and Cell 39 are configured. Cell 39 is switched off.
- System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.
- UE is in PS+PS-DCCH+DTCH_DCH (State 6-16) on Cell 1 as specified in clause 7.4 of TS 34.108.
The reference system configuration from TS ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.3 WLAN Offload / Offload Success / UTRA RRC_Connected to/from WLAN (RSRQmeas, BeaconRSSI) WLAN identifier no match/match | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.3.2 Conformance requirement | The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.3.3 Test purpose | 1. To verify that a UE offloads from UTRA RRC_Connected to WLAN when RSRQmeas < ThreshServingOffloadWLAN, Low2 and BeaconRSSI > ThreshBeaconRSSIWLAN, High
2. To verify that a UE offloads from WLAN to UTRA RRC_Connected when RSRQmeas > ThreshServingOffloadWLAN, High2 and BeaconRSSI > ThreshBeaconRSSIWLAN, Low |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.3.4 Method of test | Initial Condition
- Cell 1 and Cell 39 are configured. Cell 39 is switched off.
- System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.
- UE is in PS+PS-DCCH+DTCH_DCH (State 6-16) on Cell 1 as specified in clause 7.4 of TS 34.108.
The reference system configuration from TS ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.4 WLAN Offload / Offload Success / UTRA RRC_Connected to/from WLAN (RSRQmeas, BackhaulRateDlWLAN) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.4.2 Conformance requirement | The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.4.3 Test purpose | 1. To verify that a UE offloads from UTRA RRC_Connected to WLAN when RSRQmeas < ThreshServingOffloadWLAN, Low2 and BackhaulRateDlWLAN > ThreshBackhRateDLWLAN, High
2. To verify that a UE offloads from WLAN to UTRA RRC_Connected when RSRQmeas > ThreshServingOffloadWLAN, High2 and BackhaulRateDlWLAN > ThreshBackhRateDLWL... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.4.4 Method of test | Initial Condition
- Cell 1 and Cell 39 are configured. Cell 39 is switched off.
- System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.
- UE is in PS+PS-DCCH+DTCH_DCH (State 6-16) on Cell 1 as specified in clause 7.4 of TS 34.108
The reference system configuration from TS 3... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.5 WLAN Offload / T330 expiry | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.5.2 Conformance requirement | The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.5.3 Test purpose | 1. To verify that a UE is moved to idle state and T330 started. Upon expiry of T330, the following conditions are met for ThreshServingOffloadWLAN, Low and ThreshChUtilWLAN, Low values included in SIB 23. The UE offloads to WLAN AP.
2. To verify that a UE offloads from WLAN to UTRA RRC_Idle when RSRPmeas < ThreshServin... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.5.4 Method of test | Initial Condition
- Cell 1 and Cell 39 are configured. Cell 39 is switched off.
- System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.
- UE is in PS+PS-DCCH+DTCH_DCH (State 6-16) on Cell 1 as specified in clause 7.4 of TS 34.108
The reference system configuration from TS 3... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.6 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.7 WLAN Offload / Offload Success / UTRA RRC_Connected to/from WLAN (ANDSF and RAN rules co-existence) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.7.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.7.2 Conformance requirement | The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.7.3 Test purpose | 1. To verify that UE does not perform WLAN offload when offload condition by ANDSF rules is not satisfied and by RAN rules is satisfied.
2. To verify that UE perform WLAN offload when offload condition by ANDSF is satisfied. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.2.10.7.4 Method of test | Initial Condition
- Cell 1 and Cell 39 are configured. Cell 39 is switched off.
- UE has configured an ISRP ANDSF rule using RAN thresholds of BackhaulRate DlWLAN.- System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.
- UE is in PS+PS-DCCH+DTCH_DCH (State 6-16) on Cell 1 a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1 Cell Update | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.1 Cell Update: cell reselection in CELL_FACH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.1.1 Definition | - |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.1.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
…
1> Re-entering service area:
…
1> RLC unrecoverable error:
…
1> Cell reselection:
2> if none of the criteria for performing cell update with the causes specified above in t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.1.3 Test purpose | 1. To confirm that the UE executes a cell update procedure after the successful reselection of another UTRA cell.
2. To confirm that the UE sends the correct uplink response message when executing cell update procedure due to cell reselection. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.1.4 Method of test | Initial Condition
System Simulator: 2 cells - Cell 1 and 2 are active.
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: PS-DCCH+DTCH_FACH (state 6-11) in cell 1 as specified in clause 7.4 of TS 34.108.
Test Procedure
Table 8.3.1.1
Parameter
Unit
Cell 1
Cell 2
T0
T1
T0
T1
UTRA RF Channel Number
Mid R... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.1.5 Test requirement | At step 3 the UE shall reselect to cell 2 and then it shall transmit a CELL UPDATE message which, sets the value "cell reselection" in IE "Cell update cause".
At step 4a the UE shall transmit CELL UPDATE message which sets the value "cell reselection" in IE "Cell update cause".
At step 4b, the SS shall send a CELL UPDA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.2 Cell Update: cell reselection in CELL_PCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.2.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
…
1> Re-entering service area:
…
1> RLC unrecoverable error:
…
1> Cell reselection:
2> if none of the criteria for performing cell update with the causes specified above in t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.2.3 Test purpose | 1. To confirm that the UE, in CELL_PCH state, executes a cell update procedure after the successful reselection of another UTRA cell. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.2.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 and 2 are active.
UE: CELL_PCH (state 6-12) in cell 1 as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is brought to CELL_PCH state and is camped onto cell 1. SS configures its downlink transmission power settings according to columns "T1" in table 8.3.... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.2.5 Test requirement | After step 2 the UE shall reselect to cell 2 and transmit a CELL UPDATE message, containing the IE "Cell update cause" set to "cell reselection".
After step 4, the UE shall enter CELL_PCH state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.3 Cell Update: periodical cell update in CELL_FACH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.3.2 Conformance requirement | UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
…
1> Re-entering service area:
…
1> RLC unrecoverable error:
…
1> Cell reselection:
…
1> Periodical cell update:
2> if none of the criteria for performing cell update with the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.3.3 Test purpose | 1. To confirm that the UE executes a periodical cell update procedure following the expiry of timer T305. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.3.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 and 2 are active.
UE: PS-DCCH+DTCH_FACH (state 6-11) in cell 1 as specified in clause 7.4 of TS 34.108.
Test Procedure
Table 8.3.1.3
Parameter
Unit
Cell 1
Cell 2
T0
T1
T0
T1
UTRA RF Channel Number
Mid Range Test Frequency
Mid Range Test Frequency
CPICH Ec (FDD)
dBm... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.3.5 Test requirement | After step 1 the UE shall detect the expiry of timer T305 and then transmits a CELL UPDATE message setting value "periodical cell update" into IE "Cell update cause".
After step 3 the UE shall not send any uplink message as a response to CELL UPDATE CONFIRM message sent in step 3.
After step 4 the UE shall send a CELL ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.4 Cell Update: periodical cell update in CELL_PCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.4.2 Conformance requirement | UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
…
1> Re-entering service area:
…
1> RLC unrecoverable error:
…
1> Cell reselection:
…
1> Periodical cell update:
2> if none of the criteria for performing cell update with the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.4.3 Test purpose | 1. To confirm that the UE, in CELL_PCH state, executes a cell update procedure after the expiry of timer T305. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.4.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 and 2 are active.
UE: CELL_PCH (state 6-12) in cell 1 as specified in clause 7.4 of TS 34.108.
Test Procedure
Table 8.3.1.4
Parameter
Unit
Cell 1
Cell 2
T0
T1
T0
T1
UTRA RF Channel Number
Mid Range Test Frequency
Mid Range Test Frequency
CPICH Ec (FDD)
dBm/3.84MHz
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.4.5 Test requirement | After step 1 the UE shall detect the expiry of timer T305, it shall then move to CELL_FACH state and transmits a CELL UPDATE message with the IE "Cell update cause" set to "periodical cell update".
After step 3, the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the uplink DCCH using AM RLC.
After st... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.5 Cell Update: UL data transmission in URA_PCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.5.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
2> if the UE is in URA_PCH or CELL_PCH state; and
2> if the UE has uplink RLC data PDU or uplink RLC control PDU on RB1 or upwards to transmit:
3> perform cell update using the cause "uplink data transmission".
…
Referenc... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.5.3 Test purpose | 1. To confirm that the UE executes a cell update procedure when the UE transmits uplink data if the UE is in URA_PCH state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.5.4 Method of test | Initial Condition
System Simulator: 1cell
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
The UE has been registered in both CS and PS domains.
Test Procedure
The SS transmits a PHYSICAL CHANNEL RECONFIGURATION message with IE "RRC State Indicator" set to "URA_PCH". The UE shall reply with P... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.5.5 Test requirement | After step 4, UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message and move to URA_PCH state.
After step 5a, the UE shall move to CELL_FACH state to initiate a cell update procedure and transmits a CELL UPDATE message which is set to "uplink data transmission" in IE "Cell update cause".
After step 7, t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.6 Cell Update: UL data transmission in CELL_PCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.6.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.6.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
2> if the UE is in URA_PCH or CELL_PCH state; and
2> if the UE has uplink RLC data PDU or uplink RLC control PDU on RB1 or upwards to transmit:
3> perform cell update using the cause "uplink data transmission".
…
Referenc... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.6.3 Test purpose | 1. To confirm that the UE executes a cell update procedure when the UE transmits uplink data if the UE is in CELL_PCH state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.6.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
The UE is registered in both CS and PS domains.
Test Procedure
The UE is in the CELL_FACH state. The SS transmits a PHYSICAL CHANNEL RECONFIGURATION message with IE "RRC State Indicator" set to "CELL_P... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.6.5 Test requirement | After step 4, UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message and move to CELL_PCH state.
After step 5, the UE shall move to CELL_FACH state to initiate a cell update procedure and transmits a CELL UPDATE message which is set to "uplink data transmission" in IE "Cell update cause".
After step 7, t... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.7 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.8 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.9 Cell Update: re-entering of service area after T305 expiry and being out of service area | 8.3.1.9.1 Definition |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.9.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
…
1> Re-entering service area:
2> if none of the criteria for performing cell update with the causes specified above in the current subclause is met; and
2> if the UE is in C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.9.3 Test purpose | 1. To confirm that the UE performs a cell search after experiencing an "out of service area" condition.
2. To confirm that the UE initiates cell updating procedure if it manages to re-enter the service area. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.9.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108, using the specific message contents as specified below.
Specific Message Contents
SYSTEM INFORMATION BLOCK TYPE 1
Use the same message sub-type found in clause 6.1 of TS 34.108, with the following exc... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.9.5 Test requirement | After step 4 the UE shall transmit a CELL UPDATE message in which the IE "Cell update cause" is set to the value "re-entered service area".
After step 8 the UE shall move to CELL_FACH and then transmit a CELL UPDATE message, with the IE "Cell Update Cause" set to "re-entered service area". |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.10 Cell Update: expiry of T307 after T305 expiry and being out of service area | 8.3.1.10.1 Definition |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.10.2 Conformance requirement | When the T307 expires, the UE shall:
1> move to idle mode;
1> release all dedicated resources;
1> perform other actions when entering idle mode from connected mode as specified in TS 25.331 subclause 8.5.2;
1> and the procedure ends.
Reference
3GPP TS 25.331 clause 8.3.1 |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.10.3 Test purpose | 1 To confirm that the UE moves to idle mode after the expiry of T307, indicating that it is out of service area when attempting to perform a periodic cell updating procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.10.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Timer T305 is set to 5min.
Test Procedure
Table 8.3.1.10
Parameter
Unit
Cell 1
T0
T1
UTRA RF Channel Number
Mid Range Test Frequency
CPICH Ec (FDD)
dBm/3.84MHz
-60
-80
P-CCPCH RSCP (TDD)
dBm
-60
-80
T... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.10.5 Test requirement | After step 3 the UE shall move to idle mode. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.11 Cell Update: Success after T302 time-out | 8.3.1.11.1 Definition |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.11.2 Conformance requirement | If any or several of the following conditions are true:
- expiry of timer T302;
…
the UE shall:
1> check whether it is still in "in service area";
1> in case of a cell update procedure:
2> clear any entry for the CELL UPDATE CONFIRM message in the table "Accepted transactions" in the variable TRANSACTIONS.
If the UE de... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.11.3 Test purpose | 1. To confirm that the UE repeats the transmission of CELL UPDATE message after failing to receive any response from the SS before T302 timer expires. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.