hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.11.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Test Procedure
At the start of the test, the UE is brought to CELL_FACH state. When the UE detects the expiry of periodic cell updating timer T305 according to the system information, the UE transmits ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.11.5 Test requirement | After step 1 the UE shall detect the expiry of timer T305 then transmit a CELL UPDATE message on the uplink CCCH, setting "periodical cell update" into IE "Cell update cause".
After step 2 the UE shall re-transmits a CELL UPDATE message after the expiry of timer T302. A total of (N302+1) transmissions of CELL UPDATE me... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.12 Cell Update: Failure (After Maximum Re-transmissions) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.12.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.12.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
…
1> Periodical cell update:
…
2> if the UE is in CELL_FACH or CELL_PCH state; and
2> if the timer T305 expires; and
2> if the criteria for "in service area" as specified in subclause 8.5.5.2 in TS 25.331 is fulfilled; and
2> if periodic updating has... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.12.3 Test purpose | 1. To confirm that the UE repeats the cell update procedure upon the expiry of timer T302 and moves to idle state when its internal counter V302 is greater than N302. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.12.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_FACH (state 6-11)as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is initially in CELL_FACH state. When the UE detects the expiry of periodic cell updating timer T305, the UE transmits a CELL UPDATE message to the SS on the uplink CCCH to perform... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.12.5 Test requirement | After step 1 the UE shall transmit a CELL UPDATE message on the uplink CCCH and set value "periodical cell update" into IE "Cell update cause".
After step 3 and if K is not greater than N302, the UE shall retry to transmit a CELL UPDATE message.
After step 3 and if K is greater than N302, the UE shall stop transmitting... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.13 Cell Update: Reception of Invalid CELL UPDATE CONFIRM Message | 8.3.1.13.1 Definition |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.13.2 Conformance Requirement | If the UE receives an CELL UPDATE CONFIRM message, which contains a protocol error causing the variable PROTOCOL_ERROR_REJECT to be set to TRUE according to TS 25.331 clause 9, the UE shall perform procedure specific error handling as follows:
1> If V302 is equal to or smaller than N302, the UE shall:
2> set the variab... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.13.3 Test Purpose | 1. To confirm that the UE retransmits a CELL UPDATE message when it receives an invalid CELL UPDATE CONFIRM message, before the number of retransmissions has reached the maximum allowed value. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.13.4 Method of Test | Initial Condition
System Simulator: 1 cell
UE: CELL_PCH (state 6-12) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is brought to CELL_PCH state at the beginning of the test. SS pages the UE by sending a PAGING TYPE 1 message using the U-RNTI identity assigned during RRC connection establishment procedu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.13.5 Test Requirement | After step 1 the UE shall transmit a CELL UPDATE message on the uplink CCCH, setting "paging response" into IE "Cell update cause".
After step 3 the UE shall transmit a CELL UPDATE message on the uplink CCCH, setting "paging response" into IE "Cell update cause", "protocol error" into IE "failure cause" and "Message ex... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.14 Cell Update: Incompatible simultaneous reconfiguration | 8.3.1.14.1 Definition |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.14.2 Conformance Requirement | In case of a cell update procedure and if the received CELL UPDATE CONFIRM message
- includes "RB information elements"; and/or
- includes "Transport channel information elements"; and/or
- includes "Physical channel information elements"; and
- the variable ORDERED_RECONFIGURATION is set to TRUE because of an ongoing ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.14.3 Test Purpose | 1. To confirm that the UE retransmits a CELL UPDATE message when it receives a CELL UPDATE CONFIRM message that includes "Physical channel information elements" and UE's variable ORDERED_RECONFIGURATION is set to TRUE because of an ongoing Reconfiguration procedure, before the number of retransmissions has reached the ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.14.4 Method of Test | Initial Condition
System Simulator: 1 cell
UE: CELL_PCH (state 6-12) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is brought to CELL_PCH state at the beginning of the test. SS pages the UE by sending a PAGING TYPE 1 message using the U-RNTI identity assigned during RRC connection establishment procedu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.14.5 Test Requirement | After step 1, UE shall transmit a CELL UPDATE message.
After step 4 the UE shall re-transmit a CELL UPDATE message with failure cause set to "Incompatible simultaneous reconfiguration". |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.15 Cell Update: Unrecoverable error in Acknowledged Mode RLC SRB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.15.1 Definition | 8.3.1.15.2 Conformance Requirement
A UE shall initiate the cell update procedure in the following cases:
…
1> RLC unrecoverable error:
…
2> if the UE detects RLC unrecoverable error in an AM RLC entity:
3> perform cell update using the cause "RLC unrecoverable error".
…
In case of cell update procedure the UE shall tr... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.15.3 Test Purpose | - To confirm that the UE reports the occurrence of an unrecoverable error in a C-plane AM RLC entity by initiating cell update procedure.
- To confirm that UE enters idle mode state after receiving RRC CONNECTION RELEASE message on the downlink CCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.15.4 Method of Test | Initial Condition
System Simulator: 1 cell
UE: CS-DCCH+DTCH_DCH (state 6-9) or PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108, depending on the CN domain supported by the UE
The RRC CONNECTION SETUP message used in the initial setup should be as shown under Specific Message Contents below.
Test P... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.15.5 Test Requirement | After step 4 the UE shall transmit a CELL UPDATE message on the uplink CCCH to report the occurrence of an unrecoverable error in AM RLC entity for RB2, RB3 or RB4 data as well as cell update cause set to "RLC unrecoverable error". |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.16 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.17 Cell Update: Failure (UTRAN initiate an RRC connection release procedure on CCCH) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.17.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.17.2 Conformance requirement | When the UTRAN receives a CELL UPDATE/URA UPDATE message, the UTRAN should:
1> … or
1> initiate an RRC connection release procedure (see subclause 8.1.4 in TS 25.331) by transmitting an RRC CONNECTION RELEASE message on the downlink CCCH.
…
The UE shall receive and act on an RRC CONNECTION RELEASE message in states CEL... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.17.3 Test purpose | To confirm that the UE moves to idle state upon the reception of a RRC CONNECTION RELEASE message on CCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.17.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_FACH (state 6-11)
Test Procedure
The UE is initially in CELL_FACH state. When the UE detects the expiry of periodic cell updating timer T305, the UE transmits a CELL UPDATE message to the SS on the uplink CCCH to perform a periodical cell updating procedure. T... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.17.5 Test requirement | In step 1 the UE shall transmit a CELL UPDATE message on the uplink CCCH and set value "periodical cell update" into IE "Cell update cause".
After step 4 the UE shall enter idle mode. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.18 Cell Update: Radio Link Failure (T314>0, T315=0), CS RAB established | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.18.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.18.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
2> if none of the criteria for performing cell update with the causes specified above in the current subclause is met:
2> if the UE is in CELL_DCH state and the criteria for ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.18.4 Method of test | Initial Condition
System Simulator: 2 cells (Cell 1 and cell 2 are active).
SYSTEM INFORMATION BLOCK TYPE 1 (see specific message contents).
UE: CS_DCCH+DTCH_DCH (state 6-9).
Test Procedure
Table 8.3.1.18
Parameter
Unit
Cell 1
Cell 2
T0
T1
T2
T0
T1
T2
UTRA RF Channel Number
Mid Range Test Frequency
Mid Range Test Fre... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.18.5 Test requirement | After step 6, the UE shall detect the presence of cell 2, perform cell re-selection and transmit a CELL UPDATE message.
After step 9, the UE shall transmit a CELL UPDATE message with IE "Cell update cause" set to "Radio link failure".
After step 11, the UE shall transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE mes... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.19 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.20 Cell Update: Reception of CELL UPDATE CONFIRM Message that causes invalid configuration | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.20.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.20.2 Conformance Requirement | If the variable INVALID_CONFIGURATION is set to TRUE, the UE shall:
1> if V302 is equal to or smaller than N302:
2> if, caused by the received CELL UPDATE CONFIRM message
3> if the variable ORDERED_RECONFIGURATION is set to TRUE caused by the received CELL UPDATE CONFIRM message in case of a cell update procedure:
4> s... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.20.3 Test Purpose | 1. To confirm that the UE retransmits a CELL UPDATE message when it receives a CELL UPDATE CONFIRM message that will trigger an invalid configuration in the UE, if the number of retransmissions has not reached the maximum allowed value. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.20.4 Method of Test | Initial Condition
System Simulator: 1 cell
UE: CELL_PCH (state 6-12) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is brought to CELL_PCH state at the beginning of the test. SS pages the UE by sending a PAGING TYPE 1 message using the U-RNTI identity assigned during RRC connection establishment procedu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.20.5 Test Requirement | After step 1 the UE shall transmit a CELL UPDATE message with IE "cell update cause" set to "paging response".
After step 3 the UE shall transmit a CELL UPDATE message with IE "cell update cause" set to "paging response" and IE "failure cause" set to "invalid configuration".
After step 5, the UE shall transmit a UTRAN ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.21 Cell Update: Cell reselection to cell of another PLMN belonging to the equivalent PLMN list | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.21.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.21.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1.- Cell reselection:
- if none of the criteria for performing cell update with the causes specified above in the current clause is met; and
- if the UE is in CELL_FACH or CELL_PCH state; and
- if the UE performs cell re-selection or the variable C_R... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.21.3 Test purpose | 1. To confirm that the UE executes a cell update procedure after a successful reselection to another UTRA cell with a PLMN identity different from the original cell but with a PLMN identity that is part of the equivalent PLMN list in the UE.
2. To confirm that the UE sends the correct uplink response message when execu... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.21.4 Method of test | Initial Condition
System Simulator: 3 cells - Cell 1 is active, with the downlink transmission power shown in column marked "T0" in table 8.3.1.21, while cell 4 and cell 7 is inactive.
UE: PS-DCCH+DTCH_FACH (state 6-11) in cell 1 as specified in clause 7.4 of TS 34.108.
UE: Shall have stored equivalent PLMN list contai... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.21.5 Test requirement | After step 1c, the UE shall send a CELL UPDATE at T1.
After step 4, the UE shall refrain from sending a cell update (or any other message) after T2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.22 Cell update: Restricted cell reselection to a cell belonging to forbidden LA list (Cell_FACH) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.22.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.22.2 Conformance requirement | 1. - Cell reselection:
- if none of the criteria for performing cell update with the causes specified above in the current clause is met; and
- if the UE is in CELL_FACH or CELL_PCH state; and
- if the UE performs cell re-selection or the variable C_RNTI is empty:
- perform cell update using the cause "cell reselection... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.22.3 Test purpose | 1. To confirm that the UE executes a cell update procedure after a successful reselection of another UTRA cell with a LA identity that is not part of the list of LAs stored in the UE as "forbidden location areas for roaming".
2. To confirm that if the UE get a release message and is moved to idle mode, performs a regis... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.22.4 Method of test | Initial Condition
System Simulator:
- 2 cells - Cell 1 is active, with the downlink transmission power shown in column marked "T0" in table 8.3.1.22, while cell 4 is inactive.
- Qqualmin value for Cell 1 and Cell 4 is set to -16 dB in SIB4 (FDD only) (see specific message contents).
UE: PS-DCCH+DTCH_FACH (state 6-11) ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.22.5 Test requirement | In step 1, the UE shall send a CELL UPDATE in Cell 4 at T1 and attempt registration update in Cell 4.
After step 2, the UE shall transmit RRC CONNECTION REQUEST message.
After step 5, the UE shall transmit RRC CONNECTION SETUP COMPLETE message, followed by an INITIAL DIRECT TRANSFER message
Since the registration upda... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.23 Cell Update: HCS cell reselection in CELL_FACH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.23.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.23.2 Conformance requirement | 1. The quality level threshold criterion H for hierarchical cell structures is used to determine whether prioritised ranking according to hierarchical cell re-selection rules shall apply, and is defined by:
…
2. The cell-ranking criterion R is defined by:
where:
TEMP_OFFSETn applies an offset to the H and R criteria fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.23.3 Test purpose | 1. To confirm that the UE can read HCS related SIB information and act upon all HCS parameters in CELL_FACH state.
2. To confirm that the UE executes a cell update procedure after the successful reselection of another UTRA cell in CELL_FACH state.
3. To confirm that the UE sends the correct uplink response message when... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.23.4 Method of test | Initial Condition
System Simulator: 3 cells – Cell 1 is active with downlink transmission power shown in Column To in Table 8.3.1.23-1. Cell 2 and 3 are switched off.
UE: PS-DCCH+DTCH_FACH (state 6-11) in cell 1 as specified in clause 7.4 of TS 34.108.
Specific Message Content
For system information blocks 4 and 11 fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.23.5 Test requirement | After step 3 the UE shall reselect to cell 3 and then it shall transmit a CELL UPDATE message which, sets the value "cell reselection" in IE "Cell update cause".
After step 5 the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the uplink DCCH using AM RLC.
After step 7 the UE shall reselect to cell 2 ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.24 Cell Update: HCS cell reselection in CELL_PCH | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.24.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.24.2 Conformance requirement | 1. The quality level threshold criterion H for hierarchical cell structures is used to determine whether prioritised ranking according to hierarchical cell re-selection rules shall apply, and is defined by:
…
2. The cell-ranking criterion R is defined by:
where:
TEMP_OFFSETn applies an offset to the H and R criteria fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.24.3 Test purpose | 1. To confirm that the UE can read HCS related SIB information and act upon all HCS parameters in CELL_PCH state.
2. To confirm that the UE executes a cell update procedure after the successful reselection of another UTRA cell in CELL_PCH state.
3. To confirm that the UE sends the correct uplink response message when e... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.24.4 Method of test | Initial Condition
System Simulator: 3 cells – Cell 1 is active with downlink transmission power shown in Column To in table 8.3.1.24-1. Cell 2 and 3 are switched off.
UE: CELL_PCH (state 6-12) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Specific Message Content
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.24.5 Test requirement | After step 3 the UE shall reselect to cell 3 and then it shall transmit a CELL UPDATE message which, sets the value "cell reselection" in IE "Cell update cause".
After step 6 the UE shall reselect to cell 2 and then it shall transmit a CELL UPDATE message which, sets the value "cell reselection" in IE "Cell update caus... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.25 CELL UPDATE: Radio Link Failure (T314=0, T315=0) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.25.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.25.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
2> if none of the criteria for performing cell update with the causes specified above in the current subclause is met:
3> if the UE is in CELL_DCH state and the criteria for ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.25.3 Test purpose | 1. To confirm that the UE releases all resources and enters idle mode when there is a radio link failure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.25.4 Method of test | Initial Condition
System Simulator: 2 cells (Cell 1 and Cell 2 are active).
UE: PS-DCCH+DTCH_DCH (state 6-10) or CS-DCCH+DTCH_DCH (state 6-9) or PS+CS-DCCH+DTCH_DCH (state 6-14) in cell 1 as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) and services supported by the UE. If UE supports PS+CS but on... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.25.5 Test requirement | After step 2, the UE shall release all its radio bearers.
After step 3, the UE shall be in idle mode state in cell 2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.26 Cell Update: Radio Link Failure (T314>0, T315=0), PS RAB established | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.26.1 Definition | 8.3.1.26.2 Conformance requirement
A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
2> if none of the criteria for performing cell update with the causes specified above in the current subclause is met; and
2> if the UE is... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.26.5 Test requirement | After step 2, the UE shall detect the presence of cell 2, perform cell re-selection and transmit a CELL UPDATE message.
After step 4, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC.
After step 6, the UE shall transmit a COUNTER CHECK RESPONSE message with the M... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.27 Cell Update: Radio Link Failure (T314=0, T315>0), CS RAB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.27.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.27.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
2> if none of the criteria for performing cell update with the causes specified above in the current subclause is met; and
2> if the UE is in CELL_DCH state; and
2> if the cr... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.27.5 Test requirement | After step 2, the UE shall detect the presence of cell 2 and enter idle mode state in cell 2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.28 Cell Update: Radio Link Failure (T314=0, T315>0), PS RAB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.28.1 Definition | 8.3.1.28.2 Conformance requirement
A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
2> if none of the criteria for performing cell update with the causes specified above in the current subclause is met; and
2> if the UE is... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.28.5 Test requirement | After step 2, the UE shall detect the presence of cell 2, perform cell re-selection and transmit a CELL UPDATE message.
At step 5, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC.
At step 7, the UE shall transmit a COUNTER CHECK RESPONSE message without includin... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.29 Cell Update: Radio Link Failure (T314>0, T315>0), CS RAB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.29.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.29.2 Conformance requirement | A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
2> if none of the criteria for performing cell update with the causes specified above in the current subclause is met; and
2> if the UE is in CELL_DCH state; and
2> if the cr... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.29.5 Test requirement | After step 2, the UE shall detect the presence of cell 1 and enter idle mode state in cell 1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.30 Cell Update: Radio Link Failure (T314>0, T315>0), PS RAB | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.30.1 Definition | 8.3.1.30.2 Conformance requirement
A UE shall initiate the cell update procedure in the following cases:
1> Uplink data transmission:
…
1> Paging response:
…
1> Radio link failure:
2> if none of the criteria for performing cell update with the causes specified above in the current subclause is met; and
2> if the UE is... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.30.5 Test requirement | Case A:
After step 2, the UE shall detect the presence of cell 1 and enter idle mode state in cell 1.
Case B:
After step 2, the UE shall detect the presence of cell 1, perform cell re-selection and transmit a CELL UPDATE message.
After step 4, the UE shall transmit a TRANSPORT CHANNEL RECONFIGURATION COMPLETE message o... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.31 Cell Update: re-entering of service area from URA_PCH after T316 expiry but before T317 expiry | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.31.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.31.2 Conformance requirement | If the UE detects the "out of service area" and the UE is in URA_PCH or CELL_PCH state it shall perform the following actions:
1> start timer T316;
1> perform processes described in subclause 7.2.2.
….
In the URA_PCH or CELL_PCH state the UE shall perform the following actions:
NOTE: Neither DCCH nor DTCH are available... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.31.3 Test purpose | To confirm that the UE executes a cell update procedure when the UE re-enters the service area before the expiry of timer T317, after expiry of T316. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.31.4 Method of test | Initial Condition
System Simulator: 1 cell with URA-ID 1 and the downlink transmission power shown in column marked "T0" in table 8.3.1.31.
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108, with URA-ID 1 in the list of URA-ID.
Test Procedure
Table 8.3.1.31
Parameter
Unit
Cell 1
T0
T1
UTRA RF Channel Num... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.31.5 Test requirement | After step 2 the UE shall detect that it is out of service area and shall not send a URA UPDATE on the uplink CCCH channel.
After step 4 the UE shall transmit a CELL UPDATE message which sets value "re-entering service area" into IE "Cell update cause".
After step 6 the UE shall transmit a UTRAN MOBILITY INFORMATION CO... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.32 Cell Update: Transition from URA_PCH to CELL_DCH, start of HS-DSCH reception | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.32.1 Definition | All UEs which support FDD or TDD and HS-PDSCH.
8.3.1.32.2 Conformance requirement
When the UE receives a PAGING TYPE 1 message, it shall perform the actions as specified below.
If the UE is in connected mode, for each occurrence of the IE "Paging record" included in the message the UE shall:
1> if the IE "Used paging ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.32.5 Test requirement | After step 1, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC.
After step 3, the UE shall transmit a CELL UPDATE message.
After step 5, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the uplink DCCH using AM RLC.
8.3.1.32a Cell Upda... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.33 Cell Update: Transition from CELL_PCH to CELL_DCH, start of HS-DSCH reception, frequency modification | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.33.1 Definition | All UEs which support FDD or TDD and HS-PDSCH. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.