hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.53.5 Test requirements | 1) At step 4, UE does not perform cell reselection to cell 4, as no priority is assigned to this cell in SIB TYPE 19 at step 1.
2) At step 7, UE reselects to higher priority cell 4, as priority is now assigned to this cell and sends a CELL UPDATE with cause: cell reselection. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.54 Cell Update: Absolute priority based cell reselection when more than one cell meets the criterion | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.54.1 Definition and applicability | All UEs which support UTRA FDD, EUTRA and Rel 8 absolute priority cell reselection for high priority layers in CELL_FACH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.54.2 Conformance requirement | 5.2.6.1.2a Measurement rules for inter-frequency and inter-RAT cell reselection when absolute priorities are used
The measurement rules below apply in Idle, URA_PCH, CELL_PCH states. In CELL_FACH state, if (High Priority Layers is indicated in CELL_FACH Absolute Priority Measurement Indicator [4] and SrxlevServingCel... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.54.3 Test purpose | To confirm that if more than one cell meets the absolute priority based cell reselection criteria, the UE shall reselect the cell with the highest SrxlevnonServingCell,x among the cells meeting the criteria on the highest absolute priority layer. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.1.54.4 Method of test | Initial conditions
System Simulator:
• 3 cells Cell 1, Cell 4 and Cell 5
• Cell 1 is the active cell with SS downlink transmission power settings according to “T0” in table 8.3.1.54 below.
• All cells to be configured to transmit SIB 19 with default contents as in 34.108.
System Information Block type 11
Use the same m... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2 URA Update | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.1 URA Update: Change of URA | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.1.1 Definition | - |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.1.2 Conformance requirement | A UE in URA_PCH state shall initiate the URA update procedure in the following cases:
1> URA reselection:
2> if the UE detects that the current URA assigned to the UE, stored in the variable URA_IDENTITY, is not present in the list of URA identities in system information block type 2; or
2> if the list of URA identitie... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.1.3 Test purpose | 1. To confirm that the UE executes an URA update procedure after the successful change of URA.
2. To confirm that the UE performs an URA update procedure after it detects that SIB 2 is not broadcasted.
3. To confirm that the UE performs an URA update procedure after it detects a confirmation error of URA identity list. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.1.4 Method of test | Initial Condition
System Simulator: 2 cells: The URA-ID and transmission power for each cell is shown in Table 8.3.2.1, where the initial condition is shown in column "T0".
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108, with URA-ID 1 from the list of URA-ID in cell 1.
Test Procedure
Parameter
Unit
Ce... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.1.5 Test requirement | After step 2 the UE shall not transmit a URA UPDATE message with update cause "change of URA".
After step 4 the UE shall find that URA-ID 2 is not in its maintained list of URA-IDs. After cell reselection, the UE shall move to CELL_FACH state and transmit a URA UPDATE message setting value "change of URA" into IE "URA ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.2 URA Update: Periodical URA update and Reception of Invalid message | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.2.2 Conformance requirement | A UE in URA_PCH state shall initiate the URA update procedure in the following cases:
1> URA reselection:
…
1> Periodic URA update:
2> if the criteria for performing URA update with the causes as specified above in the current subclause are not met; and
2> if the timer T305 expires while the UE is in the service area; ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.2.3 Test purpose | 1. To confirm that the UE executes a URA update procedure after the expiry of timer T305.
2. To verify that the UE handles an invalid URA UPDATE CONFIRM message correctly when executing the URA update procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.2.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in URA_PCH state. When the UE detects the expiry of timer T305, set according to the value specified in system information, the UE moves to CELL_FACH state and transmits a URA UPDATE mes... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.2.5 Test requirement | After step 1 the UE shall detect the expiry of timer T305, move to CELL_FACH state, and transmit a URA UPDATE message which sets the value "periodical cell update" into IE "URA update cause".
After step 3 the UE shall re-transmit URA UPDATE message with IE "Protocol error indicator" set to 'TRUE' and IE "Protocol error... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.3 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.4 URA Update: loss of service after expiry of timers T307 and T305 | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.4.2 Conformance requirement | When the T305 expires and the UE detects that it is "out of service area" as specified in TS 25.331 subclause 8.5.5.1, the UE shall
1> start timer T307;
…
When the T307 expires, the UE shall:
1> move to idle mode;
1> release all dedicated resources;
1> indicate release (abort) of the established signalling connections ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.4.3 Test purpose | 1. To confirm that the UE moves to idle mode after the expiry of timer T307, following an expiry of timer T305 when it discovers that it is out of service area. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.4.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_DCH (state 6-10) as specified in clause 7.4 of TS 34.108.
Test Procedure
Table 8.3.2.4
Parameter
Unit
Cell 1
T0
T1
UTRA RF Channel Number
Mid Range Test Frequency
CPICH Ec
dBm/3.84MHz
-60
-80
P-CCPCH RSCP (TDD)
dBm
-60
-80
Table 8.3.2.4 illustrates the downli... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.4.5 Test requirement | After step 0a the UE shall respond with UTRAN MOBILITY INFORMATION CONFIRM message.
After step 2 the UE shall not transmit any URA UPDATE message on the uplink CCCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.5 URA Update: Success after Confirmation error of URA-ID list | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.5.2 Conformance requirement | The UE shall:
1> if the IE "URA identity" is included in a received message:
2> if the IE "RRC State Indicator" is included and set to "URA_PCH":
3> store this URA identity in the variable URA_IDENTITY;
3> after sending a possible message to UTRAN and entering URA_PCH state as specified elsewhere, read system informati... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.5.3 Test purpose | 1. To confirm that the UE retries to perform the URA update procedure following a confirmation error of URA-ID list. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.5.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108.
Test Procedure
At the start of this test, the UE is brought to URA_PCH state and assigned a URA with URA-ID 1. When the UE detects the expiry of timer T305 according to the system information, the UE moves to CE... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.5.5 Test requirement | After step 1 the UE shall detect the expiry of timer T305, move to CELL_FACH state, transmit a URA UPDATE message on the uplink CCCH and set value "periodic URA update" into IE "URA update cause".
After step 4 the UE shall re-transmit a URA UPDATE message with IE "URA update cause" set to "change of URA" after it detec... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.6 URA Update: Failure (V302 is greater than N302: Confirmation error of URA-ID list) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.6.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.6.2 Conformance requirement | The UE shall:
1> if the IE "URA identity" is included in a received message:
2> if the IE "RRC State Indicator" is included and set to "URA_PCH":
3> store this URA identity in the variable URA_IDENTITY;
3> after sending a possible message to UTRAN and entering URA_PCH state as specified elsewhere, read system informati... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.6.3 Test purpose | 1. To confirm that the UE make repeated attempts to perform the URA update procedure following a detection of a confirmation error of URA-ID list. It then moves to idle state when internal counter V302 is greater than N302. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.6.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is originally in URA_PCH state updated with URA-ID 1. When the UE detects the expiry of timer T305 according to the system information, the UE shall move to CELL_FACH state and transmit a U... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.6.5 Test requirement | After step 1 the UE shall detect the expiry of timer T305, then it shall move to CELL_FACH state and transmit a URA UPDATE message on the uplink CCCH, setting value "periodic URA update" in IE "URA update cause".
After step 6 and if K is not greater than N302, the UE shall retry to transmit a URA UPDATE message, settin... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.7 URA Update: Success after T302 timeout | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.7.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.7.2 Conformance requirement | If any or several of the following conditions are true:
- expiry of timer T302;
…
the UE shall:
1> stop T302 if it is running;
1> check whether it is still in "in service area";
1> in case of a URA update procedure:
2> clear any entry for the URA UPDATE CONFIRM message in the table "Accepted transactions" in the variab... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.7.3 Test purpose | 1. To confirm that the UE attempts to repeat the URA update procedure upon the expiry of timer T302. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.7.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in URA_PCH. When the UE detects the expiry of timer T305 according to the system information, the UE moves to CELL_FACH state and transmits a URA UPDATE message to the SS on the uplink C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.7.5 Test requirement | After step 1 the UE shall detect the expiry of timer T305, then it shall move to CELL_FACH state and transmit a URA UPDATE message on the uplink CCCH. The updating cause shall be set to "periodic URA update" in IE "URA update cause".
After step 3 the UE shall retry to transmit a URA UPDATE message at the expiry of time... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.8 Void | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.9 URA Update: Failure (UTRAN initiate an RRC connection release procedure on CCCH) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.9.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.9.2 Conformance requirement | When the UTRAN receives a CELL UPDATE/URA UPDATE message, the UTRAN should:
1> … or
1> initiate an RRC connection release procedure (see subclause 8.1.4 in TS 25.331) by transmitting an RRC CONNECTION RELEASE message on the downlink CCCH.
…
The UE shall receive and act on an RRC CONNECTION RELEASE message in states CEL... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.9.3 Test purpose | To confirm that the UE moves to idle state upon the reception of RRC CONNECTION RELEASE message on downlink CCCH during a URA update procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.9.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in URA_PCH state. When the UE detects the expiry of periodic URA updating timer T305, the UE moves to CELL_FACH state and transmits a URA UPDATE message to the SS on the uplink CCCH. The... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.9.5 Test requirement | After step 1 the UE shall transmit a URA UPDATE message on the uplink CCCH and set value "periodic URA update" into IE "Cell update cause".
After step 3 the UE shall enter idle state. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.10 URA Update: Reception of URA UPDATE CONFIRM message that causes invalid configuration | 8.3.2.10.1 Definition |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.10.2 Conformance Requirement | If the variable INVALID_CONFIGURATION is set to TRUE, the UE shall:
1> if V302 is equal to or smaller than N302:
2> in case of a URA update procedure:
3> set the contents of the URA UPDATE message according to TS 25.331 subclause 8.3.1.3;
3> submit the URA UPDATE message for transmission on the uplink CCCH.
2> incremen... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.10.3 Test Purpose | 1. To confirm that the UE retransmits a URA UPDATE message when it receives a URA UPDATE CONFIRM message that will trigger an invalid configuration in the UE, if the number of retransmissions has not reached the maximum allowed value. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.10.4 Method of Test | Initial Condition
System Simulator: 1 cell
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108.
Test Procedure
The UE is in URA_PCH state. When the UE detects the expiry of timer T305 according to the system information, the UE moves to CELL_FACH state and transmits a URA UPDATE message to the SS on the up... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.10.5 Test Requirement | After step 1 the UE shall detect the expiry of timer T305, then it shall move to CELL_FACH state and transmit a URA UPDATE message on the uplink CCCH, setting value "periodic URA update" into IE "URA update cause".
After step 3 the UE shall transmit a URA UPDATE message on the uplink CCCH, setting value “TRUE" in IE "P... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.11 URA Update: Cell reselection to cell of another PLMN belonging to the equivalent PLMN list | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.11.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.11.2 Conformance requirement | 1. A UE in URA_PCH state shall initiate the URA update procedure in the following cases:
- URA reselection:
- if the UE detects that the current URA assigned to the UE, stored in the variable URA_IDENTITY, is not present in the list of URA identities in system information block type 2; or
- if the list of URA identiti... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.11.3 Test purpose | 1. To confirm that the UE executes a URA update procedure after a successful reselection of another UTRA cell with a URA identity that is not the URA of the UE and with a PLMN identity different from the original cell but with a PLMN that is part of the equivalent PLMN list in the UE.
NOTE: Verifies conformance require... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.11.4 Method of test | Initial Condition
System Simulator: 3 cells - Cell 1 is active, with the downlink transmission power shown in column marked "T0" in table 8.3.2.1-1, while cell 4 and cell 7 is inactive.
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
UE: Shall have st... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.11.5 Test requirement | After Step 1d the UE shall send a URA UPATE message.
After Step 4 the UE shall refrain from sending a URA update (or any other message). |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.12 Restricted cell reselection to a cell belonging to forbidden LA list (URA_PCH) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.12.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.12.2 Conformance requirement | 1. A UE in URA_PCH state shall initiate the URA update procedure in the following cases:
- URA reselection:
- if the UE detects that the current URA assigned to the UE, stored in the variable URA_IDENTITY, is not present in the list of URA identities in system information block type 2; or
- if the list of URA identiti... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.12.3 Test purpose | 1. To confirm that the UE refrains from selecting a UTRA cell and performing a URA update if that cell has a LA identity that is part of the list of LAs stored in the UE as "forbidden location areas for roaming".
NOTE: Test case in 8.3.2.1 is a test where the UE reselects to a cell with the same LA identity as the LA ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.12.4 Method of test | Initial Condition
System Simulator: 2 cells - Cell 1 is active, with the downlink transmission power shown in column marked "T0" in table 8.3.2.12-1, while cell 4 is inactive.
Qqualmin value for Cell 1 is set to -16 dB in SIB3 and SIB4 (FDD only) (see specific message contents).
UE: URA_PCH (state 6-13) as specified i... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.12.5 Test requirement | After Step 2 the UE shall refrain from sending a URA UPDATE (or any other message). |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.13 URA Update: Change of URA due to HCS Cell Reselection | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.13.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.13.2 Conformance requirement | 1. The quality level threshold criterion H for hierarchical cell structures is used to determine whether prioritised ranking according to hierarchical cell re-selection rules shall apply, and is defined by:
…
2. The cell-ranking criterion R is defined by:
where:
TEMP_OFFSETn applies an offset to the H and R criteria fo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.13.3 Test purpose | 1. To confirm that the UE can read HCS related SIB information and act upon all HCS parameters in URA_PCH state.
2. To confirm that the UE executes an URA update procedure after the successful change of URA due to HCS Cell Reselection in URA_PCH state.
3. To confirm UE responds correctly when it re-selects to a new cel... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.13.4 Method of test | Initial Condition
System Simulator: 3 cells - Cell 1 is active with URA-ID 1 and downlink transmission power shown in column marked "T0" in table 8.3.2.13-1. Cell2 with URA-ID 1 and Cell 3 with URA-ID 2 are switched off
UE: URA_PCH (state 6-13) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supp... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.2.13.5 Test requirement | After step 4 the UE shall find that URA-ID 2 is not in its maintained list of URA-IDs. After cell reselection, the UE shall move to CELL_FACH state and transmit URA UPDATE message setting value "change of URA" into IE "URA update cause".
After step 7 the UE shall find that URA-ID 1 is not in its maintained list of URA-... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3 UTRAN Mobility Information | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.1 UTRAN Mobility Information: Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.1.2 Conformance requirement | When the UE receives a UTRAN MOBILITY INFORMATION message, it shall:
1> act on received information elements as specified in TS 25.331 subclause 8.6;
1> if the IE "UE Timers and constants in connected mode" is present:
2> store the values of the IE "UE Timers and constants in connected mode" in the variable TIMERS_AND_... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.1.3 Test purpose | 1. To confirm that the UE starts to use the new identities after it receives a UTRAN MOBILITY INFORMATION message from the SS. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.1.4 Method of test | Initial Condition
System Simulator: 1 cell
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Specific Message Contents
For system information block 1 of Cell 1 (gives IE's which are different from defaults given in 34.108 subclause 6.1) to be transmitted before idle update preamble.
System Inf... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.1.5 Test requirement | After step 2 the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the uplink DCCH that using the assigned new C-RNTI in MAC header.
After step 4 and 7 the UE shall transmit a CELL UPDATE message on the uplink CCCH with IE "Cell update cause" set to "periodical cell updating". The IE "U-RNTI" shall be i... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.2 UTRAN Mobility Information: Failure (Invalid message reception) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.2.2 Conformance Requirements | If the UTRAN MOBILITY INFORMATION message contains a protocol error causing the variable PROTOCOL_ERROR_REJECT to be set to TRUE according to TS 25.331 clause 9, the UE shall perform procedure specific error handling as follows. The UE shall:
1> transmit a UTRAN MOBILITY INFORMATION FAILURE message on the uplink DCCH u... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.2.3 Test Purpose | 1. To confirm that the UE ignore the erroneous UTRAN MOBILITY INFORMATION message and report this event to the UTRAN by sending UTRAN MOBILITY INFORMATION FAILURE message, stating the appropriate failure cause and information. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.2.4 Method of test | Initial Conditions
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_FACH (state 6-11) as specified in clause 7.4 of TS 34.108.
Specific Message Contents
For system information block 1 (given IEs which are different from defaults given in TS34.108 clause 6.1) to be transmitted before idle update preamble.
System Information B... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.2.5 Test Requirement | After step 1a the UE shall initiate a periodic cell updating procedure by transmitting CELL UPDATE message on the CCCH. In this message, the U-RNTI identity shall be set to the same value as assigned during the RRC connection establishment procedure.
After step 2 the UE shall transmit UTRAN MOBILITY INFORMATION FAILURE... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.3 UTRAN MOBILITY INFORMATION: Seamless SRNS relocation in CELL_DCH (without pending of ciphering) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.3.2 Conformance requirement | To initiate the procedure UTRAN transmits a UTRAN MOBILITY INFORMATION message to the UE on the downlink DCCH using AM or UM RLC. In case of SRNS relocation, the message is sent using UM RLC only.
When the UE receives a UTRAN MOBILITY INFORMATION message, it shall:
1> if the UTRAN MOBILITY INFORMATION message contained... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.3.3 Test purpose | 1. To confirm that the UE sends calculated START values for each CN domain to SS after a successful SRNS relocation.
2. In the case that ciphering is applied by the network, to confirm that the UE restarts ciphering following a successful SRNS relocation.
3. To confirm that the UE correctly applies integrity protection... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.3.4 Method of test | Initial Condition
System Simulator: 1 cell.
UE: PS-DCCH+DTCH_DCH (state 6-10) or CS-DCCH+DTCH_DCH (state 6-9) or PS+CS-DCCH+DTCH_DCH (state 6-14) as specified in clause 7.4 of TS 34.108, depending on the CN domain(s) supported by the UE.
Test Procedure
The UE is in the CELL_DCH state. SS then transmits a UTRAN MOBILITY... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.3.5 Test requirement | After step 1, the UE shall transmit a UTRAN MOBILITY INFORMATION CONFIRM message on the uplink DCCH using AM RLC which includes a calculated new START value according to the formula “STARTX' = MSB20 ( MAX {COUNT-C, COUNT-I | radio bearers and signalling radio bearers using the most recently configured CKX and IKX}) + 2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.4 UTRAN Mobility Information: Shared Network | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.4.2 Conformance requirement | 1. If the IE "CN information info" is present in a message, the UE shall:
1> if the IE "Primary PLMN Identity" is present:
2> forward the content of the IE "Primary PLMN identity" to upper layers.
1> else:
2> if the IE "PLMN Identity" is present:
3> forward the content of the IE "PLMN identity" to upper layers.
2. The... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.4.3 Test purpose | - To verify that the UE reacts on the IE “Primary PLMN identity” in message UTRAN MOBILITY INFORMATION, and forwards this IE to NAS.
- To verify that the UE sets the IE “PLMN Identity” in the INITIAL DIRECT TRANSFER message to the correct PLMN information received in UTRAN MOBILITY INFORMATION message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.4.4 Method of test | Initial condition
System Simulator:
- Cell 1 broadcasting PLMN1 on BCCH.
- For MASTER INFORMATION BLOCK see specific message content
User Equipment:
The UE is equipped with a USIM containing default values. The HPLMN (MCC+MNC) of the IMSI for the USIM is set to PLMN1.
The UE is registered in CS and PS domains on PLMN... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.3.4.5 Test requirements | In step 4, the UE shall respond with an INITIAL DIRECT TRANSFER message. The IE “PLMN identity” shall be set to PLMN2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4 Active set update in soft handover (FDD) |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.