hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.19 Active set update: Dual Cell (DC) and MIMO Activation by Serving Cell Change from non-DC-HSDPA capable cell to DC-HSDPA capable cell | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.19.1 Definition and applicability | All UE categories which support Dual Cell HSDPA and MIMO. UE supports F-DPCH or Enhanced F-DPCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.19.2 Conformance requirement | The purpose of the active set update procedure is to update the active set of the connection between the UE and UTRAN. This procedure shall be used in CELL_DCH state. The UE should keep on using the old RLs while configuring the new RLs. Also the UE should keep the transmitter turned on during the procedure. This proce... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.19.3 Test purpose | To confirm that the UE performs HS-DSCH serving cell change and start MIMO reception from non DC-HSDPA and non MIMO capable cell to DC-HSDPA and MIMO capable cell. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.19.4 Method of test | Initial Condition
System Simulator: 3 cells – Cell 1: non DC-HSDPA and non MIMO cell, Cell 2/3: DC-HSDPA and MIMO configured cell(s) with cell 2 (Primary Carrier) and Cell 3 (Secondary Carrier).
UE: PS_DCCH+DTCH E_DCH/HS_DSCH (state 6-17) under condition A17b, as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT s... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.19.5 Test requirements | At step 3 the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH using AM RLC.
At step 5 the UE shall transmit an ACTIVE SET UPDATE COMPLETE message on the uplink DCCH using AM RLC to acknowledge the completion of the active set addition procedure, the change of serving cell to combined DC HSDPA and MIMO... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.20 Active set update in soft handover: Radio Link addition/removal on the secondary E-DCH active set | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.20.1 Definition and applicability | All UE categories which support Dual Cell HSUPA operation. UE supports F-DPCH or Enhanced F-DPCH. UE supports FDD E-DCH category 8 or 9. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.20.2 Conformance requirement | The purpose of the active set update procedure is to update the active set of the connection between the UE and UTRAN. This procedure shall be used in CELL_DCH state. The UE should keep on using the old RLs while configuring the new RLs. Also the UE should keep the transmitter turned on during the procedure. This proce... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.20.3 Test purpose | 1. To confirm that the UE adds radio link to the secondary E-DCH set (Secondary E-DCH is in Configured state) after receiving ACTIVE SET UPDATE message, which includes IE "Radio link addition information on secondary UL frequency " and specifying the P-CPICH information of the cell to be added.
2. To confirm that the U... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.20.4 Method of test | Initial Condition
System Simulator: 3 cells – Cell 1, Cell 2/3 DC-HSUPA cell(s) with Cell 2 (Serving HS.DSCH cell/Primary uplink frequency) and Cell 3 (Secondary serving HS.DSCH cell /Secondary uplink frequency)
UE: PS_DCCH+DTCH E_DCH/HS_DSCH (state 6-18) as specified in clause 7.4 of TS 34.108 [9], following RADIO BEA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.20.5 Test requirements | At step 4, 9, 14 the UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH using AM RLC to request adding/deleting radio link on the secondary E-DCH set.
At step 7, 12 the UE shall transmit an ACTIVE SET UPDATE COMPLETE message on the uplink DCCH using AM RLC to acknowledge the completion of the active set ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.21 Active Set Update: MIMO Activation by serving cell changes with and without PCI Restrictions and S-CPICH Power Offsets (16QAM + MIMO) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.21.1 Definition and applicability | All UE categories which support MIMO and F-DPCH or Enhanced F-DPCH. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.21.2 Conformance requirement | If the UE receives an ACTIVE SET UPDATE, CELL UPDATE CONFIRM, or any reconfiguration message:
1> if the IE "MIMO parameters" is not included:
2> clear the MIMO_PARAMS variable;
2> trigger lower layers to stop operation in MIMO mode.
1> otherwise:
2> for FDD, if the IE "MIMO N_cqi_typeA/M_cqi ratio" is included:
3> stor... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.21.3 Test purpose | To confirm that the UE performs serving cell change and start MIMO reception from non MIMO capable cell to MIMO capable cell with and without PCI restriction and S-CPICH power offset. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.21.4 Method of test | Initial Condition
System Simulator: 2 cells – Cell 1 non MIMO cell, Cell 2 MIMO configured
UE: PS_DCCH+DTCH E_DCH/HS_DSCH (state 6-17) under condition A17b, as specified in clause 7.4 of TS 34.108.
Related ICS/IXIT statement(s)
- UE supports FDD
- UE category supports MIMO
- UE fully supports F-DPCH or Enhanced F-DPCH
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.21.5 Test requirements | At steps 3, UE shall transmit a MEASUREMENT REPORT message on the uplink DCCH using AM RLC.
At steps 5 UE shall transmit an ACTIVE SET UPDATE COMPLETE message on the uplink DCCH using AM RLC to acknowledge the previous ACTIVE SET UPDATE and indicate readiness to accept the new configuration at activation time.
At step ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.22 Active set update: Dual Cell (DC) Activation by Serving Cell Change from non DC-HSDPA capable cell to DC-HSDPA capable cell with discontinuous uplink transmission and downlink reception | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.22.1 Definition and applicability | All UEs which support FDD, UL DTX, DL DRX and Dual Cell HSDPA. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.22.2 Conformance requirement | The purpose of the active set update procedure is to update the active set of the connection between the UE and UTRAN. This procedure shall be used in CELL_DCH state. The UE should keep on using the old RLs while configuring the new RLs. Also the UE should keep the transmitter turned on during the procedure. This proce... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.22.3 Test purpose | To confirm that the UE performs HS-DSCH serving cell change from non DC-HSDPA capable cell to DC–HSDPA capable cell with discontinuous downlink reception and uplink transmission. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.22.4 Method of test | Initial Condition
System Simulator: 3 cells – Cell 1 non DC-HSDPA cell, Cell 2/3 DC HSDPA cell(s) with cell 2 (Anchor Carrier) and cell 3 (Secondary Carrier)
UE: PS_DCCH+DTCH E-DCH/HS_DSCH (state 6-18) under the condition A25 as specified in clause 7.4 of TS 34.108. See specific message contents for Radio Bearer Setup ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.22.5 Test requirements | At step 3 SS shall receive a MEASUREMENT REPORT message on the uplink DCCH using AM RLC.
At step 6 SS shall receive an ACTIVE SET UPDATE COMPLETE message on the uplink DCCH using AM RLC to acknowledge the completion of the active set addition procedure, the change of serving cell to DC HSDPA.
At step 7 SS should start ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23 Active set update in soft handover: Radio Link addition/deletion in multiple radio link environment with 3C-HSDPA or 4C-HSDPA remaining active | NOTE: The active set update soft handover test cases for 4C-HSDPA have been split in to Single band/nonMIMO, Single band/MIMO, Dual band/non-MIMO and Dual band/MIMO test cases. As soft handover for 4C-HSDPA is limited to adding and deleting radio links to the serving HS-DSCH cell then it has been not considered necessa... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.1 Active set update in soft handover: Radio Link addition/deletion in multiple radio link environment with 3C-HSDPA remaining active / Single band | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.1.1 Definition and applicability | All UEs which support FDD, 4C-HSDPA Single band operation with 3 carriers. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.1.2 Conformance requirement | Upon reception of an ACTIVE SET UPDATE message the UE shall act upon all received information elements as specified in 8.6, unless specified otherwise in the following.
….
The UE shall:
1> first add the RLs indicated in the IE "Radio Link Addition Information" which are not yet contained in the UEs active set;
1> remov... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.1.3 Test purpose | To confirm that the UE operation remains intact when Single band 3C HSDPA is configured and UE performs a radio link addition/removal according to the received ACTIVE SET UPDATE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.1.4 Method of test | Initial Condition
System Simulator: 4 cells Cell 1 (f1), Cell 2 (f1), Cell 4 (f2) and Cell 7 (f3) where f1, f2, and f3 are adjacent frequencies.
UE: PS_DCCH+DTCH E_DCH/HS_DSCH (state 6-18) under condition A36, as specified in clause 7.4 of TS 34.108 using Single band carrier combination with 3 carriers.
Related ICS/IXI... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.1.5 Test requirement | At step 2 SS shall receive a MEASUREMENT REPORT message on the uplink DCCH using AM RLC.
At step 4 SS shall receive an ACTIVE SET UPDATE COMPLETE message on the uplink DCCH using AM RLC to acknowledge the completion of the active set update procedure adding Cell 2 to the active set.
At step 5 SS shall receive CQI repor... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.2 Active set update in soft handover: Radio Link addition/deletion in multiple radio link environment with 3C-HSDPA remaining active / Single band / MIMO | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.2.1 Definition and applicability | All UEs which support FDD, 4C-HSDPA Single band operation with 3 carriers and MIMO. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.2.2 Conformance requirement | Upon reception of an ACTIVE SET UPDATE message the UE shall act upon all received information elements as specified in 8.6, unless specified otherwise in the following.
….
The UE shall:
1> first add the RLs indicated in the IE "Radio Link Addition Information" which are not yet contained in the UEs active set;
1> remov... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.2.3 Test purpose | To confirm that the UE operation remains intact when Single band 3C HSDPA with MIMO is configured and UE performs a radio link addition/removal according to the received ACTIVE SET UPDATE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.2.4 Method of test | Initial Condition
System Simulator: 4 cells Cell 1 (f1), Cell 2 (f1), Cell 4 (f2) and Cell 7 (f3) where f1, f2, and f3 are adjacent frequencies.
UE: PS_DCCH+DTCH E_DCH/HS_DSCH (state 6-18) under condition A34, as specified in clause 7.4 of TS 34.108 using Single band carrier combination with 3 carriers.
Related ICS/IXI... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.2.5 Test requirement | At step 2 SS shall receive a MEASUREMENT REPORT message on the uplink DCCH using AM RLC.
At step 4 SS shall receive an ACTIVE SET UPDATE COMPLETE message on the uplink DCCH using AM RLC to acknowledge the completion of the active set update procedure adding Cell 2 to the active set.
At step 5 SS shall receive composite... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.3 Active set update in soft handover: Radio Link addition/deletion in multiple radio link environment with 3C-HSDPA remaining active / Dual band | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.3.1 Definition and applicability | All UEs which support FDD, 4C-HSDPA Dual band operation and carrier combination (1,2) or (2,1). |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.3.2 Conformance requirement | Same as subclause 8.3.4.23.1.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.3.3 Test purpose | To confirm that the UE operation remains intact when Dual band 3C HSDPA is configured and UE performs a radio link addition/removal according to the received ACTIVE SET UPDATE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.3.4 Method of test | Initial Condition
System Simulator: 4 cells Cell 1 (f1), Cell 2 (f1), Cell 4 (f2) and Cell 7 (f3). For Dual band carrier combination (1,2) case then f2 and f3 are adjacent frequencies on band B. For Dual band carrier combination (2,1) case then f2 is adjacent frequency to f1 on the band A.
NOTE: Band A and band B refer... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.3.5 Test requirement | Same as subclause 8.3.4.23.1.5. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.4 Active set update in soft handover: Radio Link addition/deletion in multiple radio link environment with 3C-HSDPA remaining active / Dual band / MIMO | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.4.1 Definition and applicability | All UEs which support FDD, 4C-HSDPA Dual band operation, carrier combinations (1,2) or (2,1) and MIMO. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.4.2 Conformance requirement | Same as subclause 8.3.4.23.2.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.4.3 Test purpose | To confirm that the UE operation remains intact when Single band 3C HSDPA with MIMO is configured and UE performs a radio link addition/removal according to the received ACTIVE SET UPDATE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.4.4 Method of test | Initial Condition
System Simulator: 4 cells Cell 1 (f1), Cell 2 (f1), Cell 4 (f2) and Cell 7 (f3). For Dual band carrier combination (1,2) case then f2 and f3 are adjacent frequencies on band B. For Dual band carrier combination (2,1) case then f2 is adjacent frequency to f1 on the band A.
NOTE: Band A and band B refer... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.23.4.5 Test requirement | Same as subclause 8.3.4.23.2.5. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24 Active set update with Multiflow reconfiguration with SRBs mapped on DCH: Successful reconfiguration of Multiflow HSDPA for single and dual bands / Inter-Node B | NOTE: The Radio Bearer Reconfiguration for transition between CELL_DCH & CELL_DCH for Multiflow HSDPA have been split into single band (with two cells on one frequency and with three cells on two frequencies), and dual band (with three cells on two frequencies). |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.1 Active set update with Multiflow reconfiguration with SRBs mapped on DCH: Successful reconfiguration of 2cell/single frequency Multiflow HSDPA for single band, inter-Node B | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.1.1 Definition and applicability | UE categories that support Multiflow HSDPA operation on two cells on one frequency in single band. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.1.2 Conformance requirement | …
If the UE receives:
...
- a RADIO BEARER RECONFIGURATION message; or
it shall:
…
1> if the UE will enter the CELL_DCH state from any state other than CELL_DCH state at the conclusion of this procedure:
2> if COMMON_E_DCH_TRANSMISSION is set to FALSE before entering CELL_DCH state or IE "E-DCH info" is not included in... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.1.3 Test purpose | To confirm that the UE changes its active set and reconfigures Multiflow HSDPA operation according to the received ACTIVE SET UPDATE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.1.4 Method of test | Initial Condition
System Simulator: 3 cells
Node B 1: Cell 1 (f1, serving HS-DSCH cell)
Node B 2: Cell 2 (f1, assisting serving HS-DSCH cell)
Node B 3: Cell 4 (f1, serving HS-DSCH cell after ACTIVE SET UPDATE)
Tcell of Cell 2 is set to 1280 chips (0.5 slots); Tcell of Cell 1 is set to 2560 chips (1 slot).
UE: CELL_DCH ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.1.5 Test requirements | At step 2 the UE shall transmit the ACTIVE SET UPDATE COMPLETE message.
At step 4 the UE shall transmit UE CAPABILITY INFORMATION on SRB2.
At step 6 the UE shall transmit CQI reports. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.2 Active set update with Multiflow reconfiguration with SRBs mapped on DCH: Successful reconfiguration of 3 cell/two frequencies Multiflow HSDPA for single band, inter-Node B | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.2.1 Definition and applicability | UE categories that support Multiflow HSDPA operation on three cells on two frequencies in single band. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.2.2 Conformance requirement | Same as in sub-clause 8.3.4.24.1.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.2.3 Test purpose | To confirm that the UE changes its active set and reconfigures Multiflow HSDPA operation according to the received ACTIVE SET UPDATE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.2.4 Method of test | Initial Condition
System Simulator: 5 cells
Node B 1: Cell 1 (f1, serving HS-DSCH cell), Cell 3 (f2, secondary serving HS-DSCH cell)
Node B 2: Cell 2 (f1, assisting serving HS-DSCH cell)
Node B 3: Cell 4 (f1, serving HS-DSCH cell after ACTIVE SET UPDATE), Cell 5 (f2, secondary serving HS-DSCH cell after ACTIVE SET UPDA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.2.5 Test requirements | Same as sub-clause 8.3.4.24.1.5. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.3 Active set update with Multiflow reconfiguration with SRBs mapped on DCH: Successful reconfiguration of 3 cell/two frequencies Multiflow HSDPA for dual bands, inter-Node B | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.3.1 Definition and applicability | UE categories that support Multiflow HSDPA operation on three cells on two frequencies in two bands. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.3.2 Conformance requirement | Same as in sub-clause 8.3.4.24.1.2. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.3.3 Test purpose | To confirm that the UE changes its active set and reconfigures Multiflow HSDPA operation according to the received ACTIVE SET UPDATE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.3.4 Method of test | Initial Condition
System Simulator: 5 cells
Node B 1: Cell 1 (f1, serving HS-DSCH cell), Cell 3 (f2, secondary serving HS-DSCH cell)
Node B 2: Cell 2 (f1, assisting serving HS-DSCH cell)
Node B 3: Cell 4 (f1, serving HS-DSCH cell after ACTIVE SET UPDATE), Cell 5 (f2, secondary serving HS-DSCH cell after ACTIVE SET UPDA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.4.24.3.5 Test requirements | Same as sub-clause 8.3.4.24.1.5. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.5 Hard Handover | [Editor's note: This test is included in the "Physical channel reconfiguration", "Radio bearer establishment", "Radio bearer reconfiguration", "Radio bearer release" and "Transport channel reconfiguration".] |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.6 Inter-system hard handover from GSM to UTRAN | The content of this clause has been moved to 3GPP TS 51.010-1, clause 60. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7 Inter-system hard handover from UTRAN to GSM | Clauses 8.3.7 contains test procedures to be used for executing Inter-system Handover from UTRAN to GSM tests. Table 8.3.7‑1 contains a summary of the different combinations of parameters being tested, together with a reference to the appropriate generic test procedure. If a test uses a parameter which the UE under tes... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.1 Inter system handover from UTRAN/To GSM/Speech/Success with UEA1/UIA1 and A5/1 ciphering | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.1.1 Definition | This test case verifies the UE behaviour in the scenario of interRAT speech handover from UTRAN to GERAN including the UE capability to switch between different ciphering algorithms applied in each RAT: the UIA1/UEA1 are applied in the UTRAN cell; the A5/1 ciphering algorithm is applied in the GERAN cell. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.1.2 Conformance requirement | The UE shall be able to receive a HANDOVER FROM UTRAN COMMAND message and perform an inter-RAT handover, even if no prior UE measurements have been performed on the target cell.
The UE shall:
1> establish the connection to the target radio access technology, by using the contents of the IE "Inter-RAT message". This IE ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.1.3 Test purpose | To test that the UE supporting both GSM and UTRAN hands over from a UTRAN serving cell to the indicated channel of GSM target cell when the UE is in the speech call active state and receives an HANDOVER FROM UTRAN COMMAND.
UIA1/UEA1 are applied in the UTRAN cell. The A5/1 ciphering algorithm is applied in the GERAN cel... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.1.5 Test requirement | During the procedure for bringing the UE into UTRAN U10 state on cell 1, the UE support for A5/1 is checked in RRC Connection Setup Complete/UE RAT Specific Capability/GSM/GSM Classmark 2; and, the UEA1 support is checked in RRC Connection Setup Complete/UE Radio Access Capability/Security Capability/Ciphering Algorith... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.2 Inter system handover from UTRAN/To GSM/Data/Same data rate/Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.2.2 Conformance requirement | The UE shall be able to receive a HANDOVER FROM UTRAN COMMAND message and perform an inter-RAT handover, even if no prior UE measurements have been performed on the target cell.
The UE shall:
1> establish the connection to the target radio access technology, by using the contents of the IE "Inter-RAT message". This IE ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.2.3 Test purpose | To test that the UE hands over to the indicated channel of same data rate in the GSM target cell when it is in the data call active state in the UTRAN serving cell and receives an HANDOVER FROM UTRAN COMMAND. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.2.4 Method of test | Initial conditions
System Simulator : 2 cells - Cell 1 is UTRAN, Cell 9 is GSM. GSM 51.010 clause 40 shall be referenced for the default parameters, and clause 26.6.5.1 shall be referenced for cell allocation of cell 9.
UE: Idle state (state 2 or state 7) as specified in clause 7.4 of TS 34.108, depending on the CN dom... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.2.5 Test requirements | At step 5 the SS receives a handover access burst on the traffic channel of the GSM cell indicating that the UE has switched to the GSM cell.
At step 12 the SS receives a HANDOVER COMPLETE message indicating a successful handover to the GSM cell.
8.3.7.2a Inter system handover from UTRAN/To GSM/Data/Same data rate/Exte... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.3 Inter system handover from UTRAN/To GSM/Data/Data rate down grading/Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.3.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.3.2 Conformance requirement | The UE shall be able to receive a HANDOVER FROM UTRAN COMMAND message and perform an inter-RAT handover, even if no prior UE measurements have been performed on the target cell.
The UE shall:
1> establish the connection to the target radio access technology, by using the contents of the IE "Inter-RAT message". This IE ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.3.3 Test purpose | To test that the UE hands over to the indicated channel of lower data rate in the GSM target cell when it is in the data call active state in the UTRAN serving cell and receives an HANDOVER FROM UTRAN COMMAND. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.3.4 Method of test | Initial conditions
System Simulator : 2 cells - Cell 1 is UTRAN, Cell 9 is GSM. GSM 51.010 clause 40 shall be referenced for the default parameters, and clause 26.6.5.1 shall be referenced for cell allocation of cell 9.
UE: Idle state (state 2 or state 7) as specified in clause 7.4 of TS 34.108, depending on the CN dom... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.3.5 Test requirement | At step 5 the SS receives a handover access burst on the traffic channel of the GSM cell indicating that the UE has switched to the GSM cell.
At step 12 the SS receives a HANDOVER COMPLETE message indicating a successful handover to the GSM cell.
8.3.7.3a Inter system handover from UTRAN/To GSM/Data/Data rate down gra... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.4 Inter system handover from UTRAN/To GSM/Speech/Establishment/Success | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.4.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.4.2 Conformance requirement | The UE shall be able to receive a HANDOVER FROM UTRAN COMMAND message and perform an inter-RAT handover, even if no prior UE measurements have been performed on the target cell.
The UE shall:
1> establish the connection to the target radio access technology, by using the contents of the IE "Inter-RAT message". This IE ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.4.3 Test purpose | To test that the UE hands over to the indicated channel in the GSM target cell when it is in the call establishment phase in the UTRAN serving cell and receives an HANDOVER FROM UTRAN COMMAND. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.4.4 Method of test | Initial conditions
System Simulator : 2 cells - Cell 1 is UTRAN, Cell 9 is GSM. GSM 51.010 clause 40 shall be referenced for the default parameters, and clause 26.6.5.1 shall be referenced for cell allocation of cell 9 except the BCCH ARFCN for GSM 900 should be 18 and for GSM 1900 should be 646.
UE: Idle state (state ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.4.5 Test requirement | At step 13 the SS shall receive HANDOVER COMPLETE message on the dedicated channel of the GSM cell. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.5 Inter system handover from UTRAN/To GSM/Speech/Failure | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.5.2 Conformance requirement | If the UE does not succeed in establishing the connection to the other target radio access technology, it shall
1> revert back to the UTRA configuration;
1> establish the UTRA physical channel(s) used at the time for reception of HANDOVER FROM UTRAN COMMAND;
…
transmit the HANDOVER FROM UTRAN FAILURE message setting th... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.5.3 Test purpose | To test that the UE reactivates the old configuration and uses this to transmit a HANDOVER FROM UTRAN FAILURE message to the network including IE "Inter-RAT Handover failure cause" which is set to "physical channel failure", when it receives an HANDOVER FROM UTRAN COMMAND and the connection to GSM for handover can not ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.5.4 Method of test | Initial conditions
System Simulator : 2 cells - Cell 1 is UTRAN, Cell 9 is GSM. GSM 51.010 clause 40 shall be referenced for the default parameters, and clause 26.6.5.1 shall be referenced for cell allocation of cell 9.
UE: Idle state (state 2 or state 7) as specified in clause 7.4 of TS 34.108, depending on the CN dom... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.3.7.5.5 Test requirement | After step 4 the SS shall receive HANDOVER FROM UTRAN FAILURE message using the old UTRA configuration.
After step 5 the UE shall correctly report the GSM RSSI value. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.