hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.1.5 Test requirement | At step 3 the UE shall transmit a UE CAPABILITY INFORMATION message with the IE “Support of UTRAN ANR” is set to TRUE (TP1).
At step 12 the UE shall transmit a RRC CONNECTION SETUP COMPLETE message on uplink DCCH including the IE “ANR Logging Results Available” (TP5).
At step 14 the UE shall transmit a UE INFORMATION R... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.2 Intra-UTRA / Intra-frequency ANR measurement, logging and reporting in Cell_PCH / Ec/N0 Absolute Threshold (FDD) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.2.1 Definition and applicability | All UEs supporting UTRA FDD and UTRAN ANR measurement. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.2.2 Conformance requirement | [TS 25.304, clause 5.8.1 (TP2)]
The UE may be configured to perform UTRAN ANR measurement and logging in IDLE mode, CELL_PCH and URA_PCH state with Logging Measurement Configuration message as specified in [4]. If configured, the UE will
- perform measurements and evaluation on the cells which are not included in the n... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.2.3 Test purpose | 1. To verify that the UE correctly reads “Logged ANR configuration Info” in LOGGING MEASUREMENT CONFIGURATION message for Intra-UTRA ANR when Absolute Threshold for Ec/N0 is configured.
2. To verify that the UE triggers and performs ANR measurements on a cell not in the intra-/inter-frequency cell in list when Ec/N0 is... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.2.4 Method of test | Initial Condition
System Simulator: 3 FDD cells – Cell 1, Cell 2 and Cell 3 are active.
SYSTEM INFORMATION BLOCK TYPE 11 of Cell 1: See specific message contents.
Note: Cell 2 is listed as intra-frequency neighbour cell. Cell 3 is not included in intra-frequency info list.
SS sets the test parameter Twait to the value... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.2.5 Test requirement | At step 4, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message (TP3).
At step 7, the UE shall transmit a CELL UPDATE message on uplink CCCH with “ANR Logging Results Available” and set IE “Cell update cause” to value “cell reselection” (TP4).
At step 10 the UE shall transmit a UE INFORMATION RESPO... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.3 Intra-UTRA / Inter-frequency ANR measurement, logging and reporting in URA_PCH / RSCP Relative Threshold | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.3.1 Definition and applicability | All UEs supporting UTRA FDD or UTRA TDD and UTRAN ANR measurement. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.3.2 Conformance requirement | [TS 25.304, clause 5.8.1 (TP2)]
The UE may be configured to perform UTRAN ANR measurement and logging in IDLE mode, CELL_PCH and URA_PCH state with Logging Measurement Configuration message as specified in [4]. If configured, the UE will
- perform measurements and evaluation on the cells which are not included in the n... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.3.3 Test purpose | 1. To verify that the UE correctly reads “Logged ANR configuration Info” in LOGGING MEASUREMENT CONFIGURATION message for Intra-UTRA ANR case when Logging Relative Threshold for RSCP is configured.
2. To verify that the UE triggers and performs ANR measurements on a cell not in the intra-/inter-frequency cell info list... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.3.4 Method of test | Initial Condition
System Simulator: 3 FDD or TDD cells – Cell 1, Cell 4and Cell 5 are active.
SYSTEM INFORMATION BLOCK TYPE 11 of Cell 1: See specific message contents.
NOTE: Cell 4 is listed as inter-frequency neighbour cell. Cell 5 is not included in the inter-frequency info list.
SS sets the test parameter Twait to ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.3.5 Test requirement | At step 4, the UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message (TP3).
At step 7, the UE shall transmit a URA UPDATE message on uplink CCCH with “ANR Logging Results Available” and set IE “Cell update cause” to value “change of URA” (TP4).
At step 10 the UE shall transmit a UE INFORMATION RESPONSE ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.4 Intra-UTRA / Inter-frequency and Intra-frequency ANR measurement, logging and reporting in IDLE Mode / Ec/N0 Relative Threshold / T327 Expiry / Max Number of ANR Logged Items (FDD) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.4.1 Definition and applicability | All UEs supporting UTRA FDD and UTRAN ANR measurement. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.4.2 Conformance requirement | [TS 25.304, 5.8.1 (TP4)]
The UE may be configured to perform UTRAN ANR measurement and logging in IDLE mode, CELL_PCH and URA_PCH state with Logging Measurement Configuration message as specified in [4]. If configured, the UE will
- perform measurements and evaluation on the cells which are not included in the neighbou... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.4.3 Test purpose | 1. To verify that the UE correctly reads Logging Duration in “Logged ANR configuration Info” in LOGGING MEASUREMENT CONFIGURATION message.
2. To verify the UE behaviour when T327 expires.
3. To verify that the UE correctly reads “Logged ANR configuration Info” in LOGGING MEASUREMENT CONFIGURATION message for Intra-UTRA... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.4.4 Method of test | Initial Condition
System Simulator: 7 FDD cells – Cell 1, Cell 2, Cell 3, Cell 4, Cell 5, Cell 6, Cell 7. Cell 1 is active. Cell 2, Cell 3, Cell 4, Cell 5, Cell 6 and Cell 7 are not active.
Note 1: Cell 2, Cell 3, Cell 4, Cell 5, Cell 6 and Cell 7 are only activated one at the time. Thus is the SS requirement for simul... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.4.5 Test requirement | At step 16 the UE shall transmit a UE INFORMATION RESPONSE message including an ANR measurements for cell 2, cell 3, cell 5 and cell 6 and no ANR measurements for cell 4 or cell 7 (TP3,TP4,TP5,TP6,TP7).
At step 28 the UE shall transmit a UE INFORMATION RESPONSE message including an ANR measurements for cell 2 and no AN... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.5 Intra-UTRA / Re-configuration of ANR measurements | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.5.1 Definition and applicability | All UEs supporting UTRA FDD or UTRA TDD and UTRAN ANR measurement. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.5.2 Conformance requirement | [TS 25.331, 8.5.63.3 (TP1)]
Upon receiving the LOGGING MEASUREMENT CONFIGURATION message the UE shall:
…
1> if IE "Logged ANR configuration Info" is present:
2> if variable LOG_ANR_CONFIG was already stored, discard the existing logged measurement configuration for ANR purpose as well as the associated logged measureme... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.5.3 Test purpose | 1. Verify that UE, upon reception of new LOGGING MEASUREMENT CONFIGURATION message, clears the logged ANR configuration and stored logged measurement results, stops timer T327, stores the new logged ANR configuration and restarts the T327 timer.
2. To verify that the UE clear the logged ANR configuration and stored log... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.5.4 Method of test | Initial Condition
System Simulator: 2 FDD or TDD cells – Cell 1 and Cell 2 are active.
SYSTEM INFORMATION BLOCK TYPE 11 of Cell 1: See specific message contents.
Note: Cell 2 is not included in intra- or inter-frequency info list.
SS sets the test parameter Twait to the value of PIXIT ‘Px_AnrForUtranMeasLogWaitTime’.
U... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.1.5.5 Test requirement | At step 9 the UE shall transmit a RRC CONNECTION SETUP COMPLETE message on uplink DCCH including the IE “ANR Logging Results Available” (TP1).
At step 18 the UE shall transmit a RRC CONNECTION SETUP COMPLETE message on uplink DCCH not including the IE “ANR Logging Results Available” (TP1).
At step 27 the UE shall trans... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.2 Inter-RAT | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.2.1 Inter-RAT/ ANR measurement, logging and reporting / GERAN cell | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.2.1.1 Definition and applicability | All UEs supporting UTRA FDD or UTRA TDD, GERAN and UTRAN ANR measurements. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.2.1.2 Conformance requirement | [TS 25.304, 5.8.2.2 (TP2)]
If configured to perform inter-RAT ANR via the Logging Measurement Configuration message, the UE may perform inter-RAT ANR logging only when:
- after inter-RAT cell reselection from E-UTRAN or GSM to a normal UTRAN cell belonging to the PLMN or the list of Equivalent PLMNs where the Logging M... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.2.1.3 Test purpose | 1. To verify that the UE correctly reads “Logged ANR configuration Info” in LOGGING MEASUREMENT CONFIGURATION message for Inter-RAT ANR case when GSM Indicator is configured.
2. To verify that the UE performs Inter-RAT ANR measurement for GERAN cells not included in the inter-RAT neighbour cell list of the serving cell... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.2.1.4 Method of test | Initial Condition
System Simulator: 3 cells belonging to different routing areas – cell 1, cell 2 and cell 9 are active. Cell 1 and 2 are UTRA FDD or TDD cells. Cell 9 is GSM cells. GPRS. 51.010 clauses 20.22 and 40.1.1 shall be referenced for the default parameters of cell 9. The PLMN of Cell 1 and Cell 2 are the same... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 8.7.2.1.5 Test requirement | At step 20 the UE shall transmit a RRC CONNECTION SETUP COMPLETE message on uplink DCCH. IE “ANR Logging Results Available” shall not be included. (TP2)
At step 38 the UE shall transmit a RRC CONNECTION SETUP COMPLETE message on uplink DCCH including the IE “ANR Logging Results Available” (TP2, TP3).
At step 40 the UE ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.1 TMSI reallocation | The intention of the TMSI Reallocation procedure is to assign a new temporary identity for the UE. If the message is not understood by the UE, the network could not establish a link to the UE. As this is a common MM procedure, it can be initiated at any time. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.1.2 Conformance requirement | 1) A UE shall acknowledge a new TMSI when explicitly allocated during a location updating procedure or an incoming call.
2) The TMSI shall be updated on the USIM when the UE is correctly deactivated in accordance with the manufacturer's instructions.
3) A UE shall answer paging with this TMSI and includes it in the PAG... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.1.3 Test purpose | To verify that the UE is able to receive and acknowledge a new TMSI by means of an explicit TMSI reallocation procedure.
To verify that the UE has stored the TMSI in a non-volatile memory.
The implicit reallocation procedure is tested in clause 9.4.1. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.1.4 Method of test | Initial conditions
- System Simulator:
- two cells A and B, belonging to different location areas a and b, default parameters.
• The SIB1 IE "CN domain specific NAS system information", for the CS Domain, is set to not allowing IMSI Attach/Detach in both the cells.
- User Equipment:
- the UE has valid TMSI (= TMSI1), C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.1.5 Test requirement | At step 5 the UE shall receive and acknowledge a new TMSI (TMSI2) and has stored that in the USIM, and the UE is switched off and on after step 9 and 10.
At step 13 the UE shall transmit a new TMSI2 and includes it in the PAGING RESPONSE message.
At step 27 the UE shall answer paging with this TMSI1 and includes it in ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2 Authentication | The purpose of this procedure is to verify the user identity. A correct response is essential to guarantee the establishment of the connection. If not, the connection will drop.
The SS shall be able to handle vectors of AUTN, RAND, CK, IK, AUTS and XRES in a similar way as the MSC/BSS entities. The SS and test USIM sha... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.1 Authentication accepted | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.1.2 Conformance requirement | 1) A UE shall correctly respond to an AUTHENTICATION REQUEST message by sending an AUTHENTICATION RESPONSE message with the RES information field set to the same value as the one produced by the authentication algorithm in the network.
2) A UE shall indicate in a PAGING RESPONSE message the ciphering key sequence numbe... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.1.3 Test purpose | 1) To check that a UE correctly responds to an AUTHENTICATION REQUEST message by sending an AUTHENTICATION RESPONSE message with the RES information field set to the same value as the one produced by the authentication algorithm in the network.
2) To check that a UE indicates in a PAGING RESPONSE message the ciphering ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.1.4 Method of test | Initial conditions
- System Simulator:
- 1 cell, default parameters.
- User Equipment:
- the UE has valid TMSI, CKSN (CKSN1), CK, IK. It is "idle updated" on the cell.
Related ICS/IXIT statement(s)
None.
Test Procedure
The UE is paged. After the UE has sent a PAGING RESPONSE message to the SS, the SS initiates an authe... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.1.5 Test requirement | 1) At step 4 the UE shall send an AUTHENTICATION RESPONSE message with the RES information field set to the same value as the XRES calculated by the SS.
2) At step 8 the UE shall indicate in a PAGING RESPONSE message the ciphering key sequence number which was allocated to it through the authentication procedure. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.2 Authentication rejected by the network | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.2.2 Conformance requirement | 1) After reception of an AUTHENTICATION REJECT message the UE shall:
1.1 not perform normal location updating;
1.2 not perform periodic location updating;
1.3 not respond to paging with TMSI;
1.4 reject any request from CM entity for MM connection except for emergency call;
1.5 not perform IMSI detach if deactivated.
2... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.2.3 Test purpose | 1) To check that ,after reception of an AUTHENTICATION REJECT message, the UE:
1.1 does not perform normal location updating;
1.2 does not perform periodic location updating;
1.3 does not respond to paging with TMSI;
1.4 rejects any request from CM entity for MM connection except for emergency call;
1.5 does not perfor... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.2.4 Method of test | Initial conditions
- System Simulator:
- two cells: A and B, belonging to different location areas a and b;
- IMSI attach/detach is allowed in both cells;
- the T3212 time-out value is 1/10 hour in both cells.
- User Equipment:
- the UE has valid TMSI, CKSN, CK and IK. It is "idle updated" on cell B.
Related ICS/IXIT s... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.2.5 Test requirement | 1)
1.1 At step 24 the UE shall not send any RRC CONNECTION REQUEST on cell A or on cell B.
1.2 At step 26 the UE shall not send any RRC CONNECTION REQUEST on cell A or on cell B.
1.3 At step 9 the UE shall not respond to paging.
1.4 At step 12 the UE shall not send any RRC CONNECTION REQUEST on cell A or on cell B.
1.5... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.3 Authentication rejected by the UE (MAC code failure) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.3.1 Definition | Following a UMTS authentication challenge, the UE may reject the core network, on the grounds of an incorrect AUTN parameter (see TS 33.102).
If the UE considers the MAC code (supplied by the core network in the AUTN parameter) to be invalid, it shall send an AUTHENTICATION FAILURE message to the network, with the reje... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.3.2 Conformance requirement | 1) The UE shall respond to an AUTHENTICATION REQUEST message, with a MAC code failure in the AUTN parameter, by sending an AUTHENTICATION FAILURE message with the reject cause 'MAC failure' and start timer T3214. When an AUTHENTICATION REQUEST message containing an invalid MAC has been received by the UE from the netwo... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.3.3 Test purpose | 1) To check that a UE shall correctly respond to an AUTHENTICATION REQUEST message, with a MAC code failure in the AUTN parameter, by sending an AUTHENTICATION FAILURE message with the reject cause 'MAC failure'.
2) To check that upon reception of an IDENTITY REQUEST message, requesting for IMSI, the UE identifies itse... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.3.4 Method of test | Initial conditions
- System Simulator:
- 1 cell, default parameters.
- User Equipment:
- the UE has valid TMSI, CKSN (CKSN1), CK, IK. It is "idle updated" on the cell.
Related ICS/IXIT statement(s)
None.
Test procedure
The UE rejects an authentication. The AUTHENTICATION FAILURE is sent by UE. Upon receipt of the AUTHE... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.3.5 Test requirement | 1) At step 4 the UE shall send AUTHENTICATION FAILURE message with reject cause set to "MAC failure".
2) At step 6 the UE shall send an IDENTITY RESPONSE message including the IMSI.
3) At step 8 the UE shall send an AUTHENTICATION RESPONSE message. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.4 Authentication rejected by the UE (SQN failure) | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.4.1 Definition | Following a UMTS authentication challenge, the UE may reject the core network, on the grounds of an incorrect AUTN parameter (see TS 33.102).
If the UE considers the SQN (supplied by the core network in the AUTN parameter) to be out of range, it shall send an AUTHENTICATION FAILURE message to the network, with the reje... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.4.2 Conformance requirement | 1) The UE shall respond to an AUTHENTICATION REQUEST message, with an SQN failure in the AUTN parameter, by sending an AUTHENTICATION FAILURE message with the reject cause 'Synch failure' and start the timer T3216 and stop any of the retransmission timers that are running (i.e. T3210, T3220 or T3230). Upon receipt of a... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.4.3 Test purpose | 1) To check that a UE shall correctly respond to an AUTHENTICATION REQUEST message, with an SQN failure in the AUTN parameter, by sending an AUTHENTICATION FAILURE message with the reject cause 'Synch failure'.
2) To check that upon successfully validating the network (a second AUTHENTICATION REQUEST is received which ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.4.4 Method of test | Initial conditions
- System Simulator:
- 1 cell, default parameters.
- User Equipment:
- the UE has valid TMSI, CKSN (CKSN1), CK, IK. It is "idle updated" on the cell.
Related ICS/IXIT statement(s)
None.
Test procedure
The SS sends an AUTHENTICATION REQUEST having an invalid SQN code (i.e. uses the predefined AMFRESYNC... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.4.5 Test requirement | 1) At step 4 the UE shall reject an authentication and the AUTHENTICATION FAILURE is sent to SS with reject cause "Synch failure".
2) At step 6 the UE shall send an AUTHENTICATION RESPONSE message with the RES information field set to the same value as the XRES calculated by SS. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.5 Authentication rejected by the UE / fraudulent network | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.5.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.5.2 Conformance requirement | R99 and REL-4:
1. It can be assumed that the source of the authentication challenge is not genuine (authentication not accepted by the UE) if any of the following occur:
- After sending the AUTHENTICATION FAILURE message with the reject cause 'MAC failure' the timer T3214 expires;
- Upon receipt of the second AUTHENTIC... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.5.3 Test purpose | R99 and REL-4:
To test UE treating a cell as barred:
1. when the UE receives the second or third AUTHENTICATION REQUEST message with invalid MAC value during the T3214 is running.
2. when the timer T3214 has expired.
REL-5 and later releases:
To test UE treating a cell as barred:
1. when the UE receives the third AUTHE... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.5.4 Method of test | Initial conditions
- System Simulator:
- two cells: A and B, belonging to different location areas a and b.
- User Equipment:
- the UE has a valid TMSI. It is "idle updated" on cell A.
Related ICS/IXIT statement(s)
None.
Test procedure
A location updating procedure is initiated in cell B. The SS sends an AUTHENTICATION... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.2.5.5 Test requirement | For R99 and REL-4 UE:
Alternative 1:
- After step 6, when the UE have received the second AUTHENTICATION REQUEST message with invalid MAC value, the UE shall not attempt to access the network in cell B.
Alternative 2:
- After step6, when the UE have received the second AUTHENTICATION REQUEST message with invalid MAC va... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3 Identification | The purpose of this procedure is to check that the UE gives its identity as requested by the network. If this procedure does not work, it will not be possible for the network to rely on the identity claimed by the UE. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.1 General Identification | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.1.2 Conformance requirement | 1) When requested by the network the UE shall send its IMSI.
2) When requested by the network the UE shall send the TMSI which it was previously allocated.
3) When requested by the network the UE shall send its IMEI as stored in the UE.
4) When requested by the network the UE shall send its IMEISV as stored in the UE.
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.1.3 Test purpose | 1) To verify that the UE sends identity information as requested by the system in the following cases: IMSI and TMSI are requested in non-security mode, IMEI is requested in security mode.
2) To verify that the UE sends its IMEI, when requested to do so, in non- security mode.
3) To verify that the UE sends its IMEISV,... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.1.4 Method of test | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.1.4.1 Identification | Initial conditions
- System Simulator:
- 1 cell, default values.
- User Equipment:
- the UE has a valid TMSI. It is "idle updated" on the cell.
Related ICS/IXIT statement(s)
IMEI of the UE.
IMEISV of the UE.
Test Procedure
The SS requests identity information from the UE:
- IMSI in non security mode;
- allocated TMSI i... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.1.5 Test requirement | 1) At step 4 the UE shall send its IMSI.
2) At step 6 the UE shall send the TMSI which it was previously allocated.
3) At step 6b and step 10 the UE shall send its IMEI as stored in the UE.
4) At step 6d the UE shall send its IMEISV as stored in the UE. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.2 Handling of IMSI shorter than the maximum length | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.2.2 Conformance requirement | The UE shall be capable of handling an IMSI that is not of the maximum length.
Reference(s)
TS 24.008 clause 10.5.1.4. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.2.3 Test purpose | To check that the UE behaves correctly when activated with an IMSI of length less than the maximum length.
In this condition, the UE shall:
- perform location updating;
- answer to paging with IMSI;
- give the correct IMSI when asked by an IDENTITY REQUEST;
- attempt CM connection establishment when requested to;
- att... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.2.4 Method of test | Initial conditions
- System Simulator:
- 1 cell, default values;
- IMSI attach/detach bit set to "1".
- User Equipment:
- the UE has no valid TMSI;
- it is "idle updated";
- the IMSI has the value 001011234.
Related ICS/IXIT statement(s)
On/Off switch - Yes/No.
Foreseen final state of UE
The UE has no valid TMSI. It is... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.3.2.5 Test requirement | At step 2 the UE shall answer to paging with IMSI.
At step 4 the UE shall answer to the SS with the correct IMSI in an IDENTITY RESPONSE message.
At step 19 the IMSI is sent by the network in a TMSI REALLOCATION COMMAND message, at step 27 the UE shall attempt IMSI detach.
At step 34 the UE shall perform location updat... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4 Location updating | This procedure is used to register the UE in the network. If it is not performed correctly, no call can be established. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.1 Location updating / accepted | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.1.2 Conformance requirement | 1.
1.1 if the network accepts a location updating from the UE and reallocates a TMSI in the LOCATION UPDATING ACCEPT message the UE shall acknowledge the reception of the new TMSI;
1.2 the UE shall answer to paging with this TMSI and include it in a PAGING RESPONSE message.
2 If the network accepts a location updating ... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.1.3 Test purpose | 1) To test the behaviour of the UE if the network accepts the location updating of the UE.
For the network response three different cases are identified:
1.1) TMSI is allocated;
1.2) location updating accept contains neither TMSI nor IMSI;
1.3) location updating accept contains IMSI. |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.1.4 Method of test | Initial conditions:
- System Simulator:
- two cells, A and B, belonging to different location areas with location area identification a and b of the same PLMN;
- IMSI attach/detach is allowed in both cells;
- the T3212 time-out value is 1/10 hour in both cells.
- User Equipment:
- the UE has a valid TMSI (=TMSI1) and C... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.1.5 Test requirement | At step 7 the UE shall acknowledge the reception of the new TMSI (TMSI2).
At step 11 the UE shall answer to paging with this TMSI (TMSI2).
At step 23 the UE shall answer to paging with the last allocated TMSI (TMSI2).
At step 35 the UE shall not answer paging with the last allocated TMSI, but at step 37 the UE shall st... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2 Location updating / rejected | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2.1 Location updating / rejected / IMSI invalid | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2.1.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2.1.2 Conformance requirement | 1) If the network rejects a location updating from the UE with the cause "IMSI unknown in HLR", "Illegal MS" or "Illegal ME" the UE shall:
1.1 not perform normal location updating;
1.2 not perform periodic location updating;
1.3 not respond to paging with IMSI;
1.4 not respond to paging with TMSI;
1.5 reject any reques... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2.1.3 Test purpose | To test the behaviour of the UE if the network rejects the location updating of the UE with the cause "IMSI unknown in HLR", "illegal MS" or "Illegal ME". |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2.1.4 Method of test | Initial conditions
- System Simulator:
- two cells: A and B, belonging to different location areas of the same PLMN;
- IMSI attach/detach is allowed in both cells;
- the T3212 time-out value is 1/10 hour in both cells.
- User Equipment:
- the UE has valid TMSI(= TMSI1), CKSN and CK, IK. It is "idle updated" on cell A.
... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2.1.5 Test requirement | 1) 1.1 At step 10 the UE shall not perform normal location updating.
1.2 At step 12 the UE shall not perform periodic location updating.
1.3 At step 14 the UE shall not respond to paging with IMSI.
1.4 At step 16 the UE shall not respond to paging with TMSI.
1.5 At step 18 the UE shall reject a MO CM connection.
1.6 At... |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2.2 Location updating / rejected / PLMN not allowed | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2.2.1 Definition | |
4251e2eb3ecde7c73983ce7a4175ddf3 | 34.123-1 | 9.4.2.2.2 Conformance requirement | 1) If the network reject a location updating from the UE with the cause "PLMN not allowed" the UE shall:
1.1 not perform periodic updating;
1.2 not perform IMSI detach when switched off;
1.3 not perform IMSI attach when switched on in the same location area;
1.4 not perform normal location updating when in the same PLM... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.